Veratron OceanLink Series Manuale utente
A2C15587600
OCEANLINK 4.3
MARINE DISPLAY
USER MANUAL
rev. AB
EN
DE
IT
FR
ES
TABLE OF CONTENTS
A2C15587600
TABLE OF
CONTENTS
Safety Information 3
Introduction 5
Installation 6
Connections 9
Electrical Dia rams 11
Gettin Started 15
Data Screens 17
Screen Confi uration 22
System Settin s 24
Sensor Confi urations 28
Alarms 35
Troubleshootin 39
Technical Data 40
Spare Parts, Sensors and Accessories 42
SAFETY INFORMATION
A2C15587600
SAFETY INFORMATION
WARNING
•No smokin ! No open fire or heat sources!
•The product was developed, manufactured and
inspected accordin to the basic safety requirements
of EC Guidelines and state-of-the-art technolo y.
•The instrument is desi ned for use in rounded
vehicles and machines as well as in pleasure boats,
includin non-classified commercial shippin .
•Use our product only as intended. Use of the product
for reasons other than its intended use may lead to
personal injury, property dama e or environmental
dama e. Before installation, check the vehicle
documentation for vehicle type and any possible
special features!
•Use the assembly plan to learn the location of the
fuel/hydraulic/compressed air and electrical lines!
•Note possible modifications to the vehicle, which
must be considered durin installation!
•To prevent personal injury, property dama e or
environmental dama e, basic knowled e of motor
vehicle/shipbuildin electronics and mechanics is
required.
•Make sure that the en ine cannot start
unintentionally durin installation!
•Modifications or manipulations to VDO products can
affect safety. Consequently, you may not modify or
manipulate the product!
•When removin /installin seats, covers, etc., ensure
that lines are not dama ed and plu -in connections
are not loosened!
•Note all data from other installed instruments with
volatile electronic memories.
SAFETY DURING INSTALLATION
•Durin installation, ensure that the product’s
components do not affect or limit vehicle functions.
Avoid dama in these components!
•Only install undama ed parts in a vehicle!
•Durin installation, ensure that the product does not
impair the field of vision and that it cannot impact the
driver’s or passen er’s head!
•A specialized technician should install the product. If
you install the product yourself, wear appropriate
work clothin . Do not wear loose clothin , as it may
et cau ht in movin parts. Protect lon hair with a
hair net.
•When workin on the on-board electronics, do not
wear metallic or conductive jewelry such as
necklaces, bracelets, rin s, etc.
•If work on a runnin en ine is required, exercise
extreme caution. Wear only appropriate work
clothin as you are at risk of personal injury, resultin
from bein crushed or burned.
•Before be innin , disconnect the ne ative terminal
on the battery, otherwise you risk a short circuit. If the
vehicle is supplied by auxiliary batteries, you must
also disconnect the ne ative terminals on these
batteries! Short circuits can cause fires, battery
explosions and dama es to other electronic systems.
Please note that when you disconnect the battery, all
volatile electronic memories lose their input values
and must be repro rammed.
•If workin on asoline boat motors, let the motor
compartment fan run before be innin work.
•Pay attention to how lines and cable harnesses are
laid so that you do not drill or saw throu h them!
•Do not install the product in the mechanical and
electrical airba area!
•Do not drill holes or ports in load-bearin or
stabilizin stays or tie bars!
•When workin underneath the vehicle, secure it
accordin to the specifications from the vehicle
manufacturer.
•Note the necessary clearance behind the drill hole or
port at the installation location. Required mountin
depth: 65 mm.
•Drill small ports; enlar e and complete them, if
necessary, usin taper millin tools, saber saws,
keyhole saws or files. Deburr ed es. Follow the safety
instructions of the tool manufacturer.
•Use only insulated tools, if work is necessary on live
parts.
•Use only the multimeter or diode test lamps
provided, to measure volta es and currents in the
vehicle/machine or boat. Use of conventional test
SAFETY INFORMATION
A2C15587600
lamps can cause dama e to control units or other
electronic systems.
•The electrical indicator outputs and cables
connected to them must be protected from direct
contact and dama e. The cables in use must have
enou h insulation and electric stren th and the
contact points must be safe from touch.
•Use appropriate measures to also protect the
electrically conductive parts on the connected
consumer from direct contact. Layin metallic,
uninsulated cables and contacts is prohibited.
SAFETY AFTER INSTALLATION
•Connect the round cable ti htly to the ne ative
terminal of the battery.
•Reenter/repro ram the volatile electronic memory
values.
•Check all functions.
•Use only clean water to clean the components. Note
the In ress Protection (IP) ratin s (IEC 60529).
ELECTRICAL CONNECTION
•Note cable cross-sectional area!
•Reducin the cable cross-sectional area leads to
hi her current density, which can cause the cable
cross-sectional area in question to heat up!
•When installin electrical cables, use the provided
cable ducts and harnesses; however, do not run
cables parallel to i nition cables or to cables that lead
to lar e electricity consumers.
•Fasten cables with cable ties or adhesive tape. Do not
run cables over movin parts. Do not attach cables to
the steerin column!
•Ensure that cables are not subject to tensile,
compressive or shearin forces.
•If cables are run throu h drill holes, protect them
usin rubber sleeves or the like.
•Use only one cable stripper to strip the cable. Adjust
the stripper so that stranded wires are not dama ed
or separated.
•Use only a soft solderin process or commercially
available crimp connector to solder new cable
connections!
•Make crimp connections with cable crimpin pliers
only. Follow the safety instructions of the tool
manufacturer.
•Insulate exposed stranded wires to prevent short
circuits.
•Caution: Risk of short circuit if junctions are faulty or
cables are dama ed.
•Short circuits in the vehicle network can cause fires,
battery explosions and dama es to other electronic
systems. Consequently, all power supply cable
connections must be provided with weldable
connectors and be sufficiently insulated.
•Ensure round connections are sound.
•Faulty connections can cause short circuits. Only
connect cables accordin to the electrical wirin
dia ram.
•
If operatin the instrument on power supply units,
note that the power supply unit must be stabilized
and it must comply with the followin standard: DIN
EN 61000, Parts 6-1 to 6-4.
INTRODUCTION
A2C15587600
INTRODUCTION
OceanLink Master 4.3" is a multifunction display
that lets you monitor en ines and related sensor
parameters. Up to four en ines can be connected
to the display.
The inte rated NMEA 2000 ateway let you
acquire en ine data also via analo sensors or SAE
J1939, to then convert and distribute them on
NMEA 2000 network.
The display mana es up to two resistive sensors,
two capacitive sensors (4-20mA) and one
frequency input for the tachometer.
All data are also distributed on the EasyLink
network to a maximum of 16 52mm OceanLink
au es.
NMEA 2000 connectivity lets you view navi ation
data from other devices on the network, such as
wind, compass, GPS, speed, and depth data.
ARCHITECTURE
Followin is an example of an application with two displays, one used as a ateway and the other as a NMEA
2000 monitor.
INSTALLATION
A2C15587600
INSTALLATION
WARNING
Before startin work, disconnect the ne ative terminal of the battery to avoid the risk of a short circuit. If the vehicle is
equipped with additional batteries, the ne ative terminal of all batteries must also be disconnected if necessary. Short
circuits can burn cables, explode batteries and cause dama e to other electronic systems. Remember that by
disconnectin the battery, all data entered in the temporary electronic memory will be lost and will have to be
repro rammed.
BEFORE THE ASSEMBLY
1. Before startin work, switch off the
i nition and remove the i nition key. If
necessary, remove the main power
switch.
2. Disconnect the ne ative terminal of the
battery. Do not allow the battery to be
reconnected by mistake.
3. When mountin the device in the vicinity
of a ma netic compass, maintain a
protective distance from the compass.
4. Purchase an NMEA 2000 drop cable
with five-pin M12 connector (max drop
cable len th 6 m) and a video cable with
a compatible four-pin M12 connector
(A2C1845710001).
INSTALLATION
A2C15587600
PANEL MOUNTING
WARNING
•Do not drill holes or installation openin s in supportin or stabilizin beams!
•The mountin location must have sufficient clearance behind the mountin holes or openin s.
•Drill small holes with the drill, if necessary, enlar e them usin a conical cutter, scroll saw, tail saw or file and finish
them. Deburr the ed es. It is essential to observe the safety instructions of the tool manufacturer.
1. If installed, remove the bezel [A].
2. Drill a hole in the panel usin the drillin
template (see next pa e of this
document) and considerin the device
dimensions [B].
3. Thread the cables throu h the hole and
connect the connectors.
NOTE: screw in M12 connectors with care.
If they screw with difficulty, remove and
screw them back in.
4. Insert the device from the front and
ti hten the four screws [C].
5. Remove the protection film from the
display and make sure it is clean and dry.
6. Install the bezel with the sun cover.
A
B
C
INSTALLATION
A2C15587600
CONNECTIONS
A2C15587600
CONNECTIONS
ENGINE CONNECTOR [A]
Pi No. Wire color Descriptio
1 Red KL. 30 – Battery power 12 / 24 V
2 Black KL. 31 - Ground
3 White Alarm output
4 Green Frequency sensor si nal - RPM
5 Blue SAE J1939 – CAN L
6 Blue / White SAE J1939 – CAN H
7 Yellow KL. 15 – I nition positive
8 Grey Resistive sensor input
9 Brown Resistive sensor input
10 Oran e KL.58 – Illumination Day/Ni ht
11 Li ht Blue 4-20 mA sensor input
12 Violet 4-20 mA sensor input
Molex MX150 12-poles connector, cable view
and wire harness A2C1507870001 (included)
CONNECTIONS
A2C15587600
NMEA 2000® CONNECTOR [B]
Pi No. Descriptio
1 Shield
2 NET-S (V+)
3 NET-C (V-)
4 NET-H (CAN H)
5 NET-L (CAN L)
Micro-C M12 5 poles plu
male, cable view
EASYLINK CONNECTOR [C]
Pi No. Descriptio
1 12V Power
2 EasyLink Data
3 GND
AMP SuperSeal 1.5 3 poles plu
female, cable view
Altri manuali per OceanLink Series
1
Questo manuale è adatto per i seguenti modelli
2
Indice
Lingue:
Altri manuali Veratron Monitor
