Verkada CD52 Manuale utente

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

[email protected]

All specifications are subject to change without notice

Install Guide

CD52 Outdoor Dome Camera

Document

Document Details

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

[email protected]

All specifications are subject to change without notice

V1.0 (20211208)

(V1.0 first published 20211208)

Firmware

Firmware version can be verified on

Verkada Command command.verkada.com.

Introduction

What’s in the box

What you’ll need

●A working Internet connection.

●802.3af Power over Ethernet (PoE) switch,

or a PoE injector. For operation below

-20° C, use 802.3at PoE.

●A smartphone or laptop

●A #2 Phillips screwdriver or power drill

with a #2 Phillips driver bit

●1/4 inch (6.5mm) drill bit for wall anchors

●1/8 inch (3mm) drill bit for pilot holes

●A Cat5 or Cat6 Ethernet cable with a

0.2-0.25 inch outside diameter

(5-6.5mm)

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

[email protected]

All specifications are subject to change without notice

CD52 Outdoor Camera Mount plate

(Attached to camera)

Mounting template

2 Pole straps Cable gland wrench T10 Security Torx screwdriver

Connect

For easy registration and setup, scan the QR

code on the product.

If you prefer to manually register your product,

please proceed to:

If you prefer to manually register your product,

verkada.com/start

If you prefer to manually register your product,

4 Wall anchors4 M4 x 25mm PH2

wall screws

Conduit adapter

(with 2 screws and anchors)

Desiccant

Introduction

Camera Details

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

[email protected]

All specifications are subject to change without notice

Placement

Mount the camera on a wall or ceiling. Try to

keep the camera 8 to 10 feet above the ground.

For best night vision, avoid overhangs or

obstructions. These may reflect the camera’s IR

illumination and reduce the image clarity in

night mode.

LED Behavior

Solid Orange

Camera is on and booting up.

Flashing Orange

Camera is updating firmware.

Flashing Blue

Camera is recording data but

cannot reach the server.

Solid Blue

Camera is running, connected,

and recording data.

Installation

Cable Gland Assembly 1/2

To seal the Ethernet cable,

disassemble the cable gland and

feed the Ethernet cable through

the baseplate through-hole.

1. Place the rubber seal around the

cable. Push the plastic collar firmly

over the rubber seal until it snaps

into position.

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

[email protected]

All specifications are subject to change without notice

2. Firmly insert the seal and collar

assembly into the pass-through

until it is secured in position.

Installation

Cable Gland Assembly 2/2

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

[email protected]

All specifications are subject to change without notice

4. Gently tighten down the metal nut by hand.

You should still be able to move the cable

back and forth through the gland, but have

enough resistance for it to remain in place.

For detailed installation instructions, visit

www.verkada.com/support

3. Place the metal nut over the

rubber seal and engage the

threads on the pass-through.

Installation

Assembly 1/2

Note

Please keep the protective film adhered to the clear

bubble until completing the final step of installation.

Use the provided T10

Security Torx security

screwdriver to loosen the

screws and lift the cover.

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

[email protected]

All specifications are subject to change without notice

Connect the camera to

an 802.3af/at Power

over Ethernet port on

your network.

Installation

Assembly 2/2

Note

An orange LED on the camera’s Ethernet port will indicate that it is powered and

booting up. A green LED on the Ethernet port will indicate the camera is active.

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

[email protected]

All specifications are subject to change without notice

Gently pull the cable through the

through-hole so it has some

slack, but will not interfere with

the top cover.

Pulling the Ethernet cable too

tight will strain the cable which

may impact data performance.

Too much slack in the Ethernet

cable may create top cover

installation issues.

Firmly tighten using the provided Cable gland wrench.

Installation

Mounting

Note

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

[email protected]

All specifications are subject to change without notice

Note

1. Use the provided T10 security Torx security screwdriver to

loosen the screws and lift the cover. To remove the

mount plate, loosen the mount plate screws and twist

the camera counter-clockwise. Lift the camera vertically

off the base plate and set aside.

2. Use the provided mounting template to mark wall

mount holes. For a junction box mount, use the

mounting template to determine the correct hole

pattern.

3. For a solid material like wood or metal, drill 1/8 inch pilot

holes. Drive mounting screws directly into the pilot holes.

4. For drywall, drill 1/4 inch holes. Insert plastic anchors into

holes and drive mounting screws into anchors.

5. To secure the camera, place it over the mount plate

screws and twist counter-clockwise. Tighten the mount

plate screws with a Phillips screwdriver.

Installation

Adjust

Note

Adjust your camera to the desired viewing angle. Use the online stream to

confirm image orientation.

Image can be flipped 180˚ online in Command.

Default image orientation is indicated by markings on the lens face. Video

orientation is also adjustable from within the Verkada application.

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

[email protected]

All specifications are subject to change without notice

Indice

Manuali Telecamera di sicurezza popolari di altre marche

Okina USA

Okina USA SIR36-870VF650LP Manuale utente

Divio

Divio NDR155PA Manuale utente

Canon

Canon VB-C500D Manuale utente

Easy Access

Easy Access EasyGuard Manuale utente

Vivotek

Vivotek FD9389-EHV-v2 Manuale utente

TUYA

TUYA COSMO W2 Manuale utente

Eusso

Eusso UNC7500-IR Guida all'installazione

urmet domus

urmet domus 1096/204 Manuale utente

VC VC20 series Manuale utente

Axis

Axis Q1614 Manuale utente

ieGeek

ieGeek DD201 Manuale utente

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuale utente

Vicon

Vicon V662-D-1 Istruzioni operative

Grundig

Grundig GCH-K0274P Manuale utente

Lorex

Lorex VANTAGE LBC7032 Manuale utente

4xem

4xem WPT Manuale utente

Samsung

Samsung SCV-3082 Manuale utente

Vitek

Vitek VTC-C544 Manuale utente