Vermeer SC362 Manuale utente

SC362 Stump Cutter

SC362_o1_00

Serial No. 101 -

Order No. 105400CT8

Cabled Assembly Order No. 163708565

Operator’s

Manual

Introduction SC362 Stump Cutter

Introduction

This manual explains the proper operation of your machine. Study and understand these instructions thoroughly before operating or

maintaining the machine. Failure to do so could result in personal injury or equipment damage. Consult your Vermeer dealer if you

do not understand the instructions in this manual, or need additional information.

The instructions, illustrations, and specifications in this manual are based on the latest information available at time of publication.

Your machine may have product improvements and features not yet contained in this manual.

Vermeer Corporation reserves the right to make changes at any time without notice or obligation.

Operation instructions are included in the two Operator’s Manuals provided with the machine. The tethered (cabled)

manual must remain attached to the machine for ready reference. Store it in the manual storage box when not in use.

Lubrication and maintenance procedures are in the Maintenance Manual provided with the machine. Refer to it for all

lubrication and maintenance procedures.

Additional copies of the manuals, and Operations and Safety video, are available from your dealer. Reorder numbers are listed on the

front covers of the manuals and on the video.

Copies of this manual are available in Spanish from your dealer. Other languages may also be available.

Se dispone de ejemplares de este manual en español.

NOTICE TO OWNER

You are requested to notify Vermeer Corporation when you have purchased a used Vermeer machine. Notify the Customer Data

Department by telephone: 800-829-0051 or 641-628-3141; email: customerdata@vermeer.com; internet: www.vermeer.com or

www.vermeerag.com; or letter: Customer Data Dept., Vermeer Corporation, PO Box 200, Pella IA 50219 USA. Upon request, an

owner of a used Vermeer machine will receive one free set of Operator’s, Maintenance and Parts manuals.

SC362 Stump Cutter Introduction

Orientation: Forward travel of this machine is away from the cutter wheel. Right and left sides are determined when facing in the

direction of forward travel.

TRADEMARKS

VERMEER, VERMEER Logo, AUTOSWEEP, and YELLOW JACKET are trademarks of Vermeer Manufacturing Company.

VANGUARD and BRIGGS & STRATTON are trademarks of Briggs and Stratton Corporation.

FORWARD

FORWARDDIRECTION

Introduction SC362 Stump Cutter

VERMEER NEW INDUSTRIAL EQUIPMENT LIMITED WARRANTY

(EFFECTIVE AUGUST 1, 2013) WARRANTY PERIOD: 12 Months / 1000 Hours

Vermeer Corporation (hereinafter “Vermeer”) warrants each new Industrial product of Vermeer’s manufacture to be free from defects

in material and workmanship, under normal use and service for one (1) full year after initial purchase/retail sale or 1000 operating

hours, whichever occurs first. This Limited Warranty shall apply only to complete machines of Vermeer’s manufacture, parts are

covered by a separate Limited Warranty. EQUIPMENT AND ACCESSORIES NOT OF VERMEER’S MANUFACTURE ARE

WARRANTED ONLY TO THE EXTENT OF THE ORIGINAL MANUFACTURER’S WARRANTY AND SUBJECT TO

THEIR ALLOWANCE TO VERMEER ONLY IF FOUND DEFECTIVE BY SUCH MANUFACTURER.

EXTENDED WARRANTY OPTIONS ARE AVAILABLE FOR PURCHASE WARRANTY TERMS During the Limited

Warranty period specified above, any defect in material or workmanship in any warranted item of Vermeer Industrial Equipment not

excluded below shall be repaired or replaced at Vermeer’s option without charge by any authorized independent Vermeer dealer. The

warranty repair or replacement must be made by a Vermeer independent authorized dealer at the dealer’s location. Vermeer will pay

for replacement parts and such authorized dealer’s labor in accordance with Vermeer’s labor reimbursement policy. Vermeer reserves

the right to supply remanufactured replacement parts as it deems appropriate.

RETAIL PURCHASER RESPONSIBILITY: This Limited Warranty requires proper maintenance and periodic inspections of the

Industrial Equipment as indicated in the Operator’s/Maintenance Manual furnished with each new Industrial Equipment. The cost

of routine or required maintenance and services is the responsibility of the retail purchaser. The retail purchaser is required to keep

documented evidence that these services were performed. This Vermeer New Industrial Equipment Limited Warranty may be

subject to cancellation if the above requirements are not performed. Vermeer Industrial Equipment with known failed or defective

parts must be immediately removed from service.

SC362 Stump Cutter Introduction

EXCLUSIONS AND LIMITATIONS

The warranties contained herein shall NOT APPLY TO:

1) Any defect which was caused (in Vermeer’s sole judgment) by other than normal use and service of the Industrial Equipment,

or by any of the following; (i) accident (ii) misuse or negligence (iii) overloading (iv) lack of reasonable and proper maintenance

(v) improper repair or installation (vi) unsuitable storage (vii) non-Vermeer approved alteration or modification (viii) natural

calamities (ix) vandalism (x) parts or accessories installed on Industrial Equipment which were not manufactured or installed

by Vermeer authorized dealers (xi) the elements (xii) collision or other accident.

(2) Any Industrial Equipment whose identification numbers or marks have been altered or removed or whose hour meter has

been altered or tampered with.

(3) Any Industrial Equipment which any of the required or recommended periodic inspection or services have been performed

using parts not manufactured or supplied by Vermeer or meeting Vermeer Specifications including, but without limitation,

engine tune-up parts, engine oil filters, air filters, hydraulic oil filters, and fuel filters.

(4) New Industrial Equipment delivered to the retail purchaser in which the equipment/warranty registration has not been

completed and returned to Vermeer within ten (10) days from the date of purchase.

(5) Any defect which was caused (in Vermeer’s sole judgment) by operation of the Industrial Equipment not abiding by standard

operating procedures outlined in the Operator’s Manual.

(6) Engine, battery, and tire Limited Warranties and support are the responsibility of the respective product’s manufacturer.

(7) Transportation costs, if any, of transporting to the Vermeer dealer. Freight costs, if any, of transporting replacement parts to

the Vermeer dealer.

(8) The travel time of the Vermeer dealer’s service personnel to make a repair on the retail purchaser’s site or other location

(9) In no event shall Vermeer’s liability exceed the purchase price of the product,

10) Vermeer shall not be liable to any person under any circumstances for any incidental or consequential damages (including but

not limited to, loss of profits, out of service time) occurring for any reason at any time.

(11) Diagnostic and overtime labor premiums are not covered under this Limited Warranty Policy. Oils and fluids are not covered

under this Limited Warranty.

Introduction SC362 Stump Cutter

(12) Depreciation damage caused by normal wear, lack of reasonable and proper maintenance, failure to follow operating

instructions, misuse, lack of proper protection during storage.

(13) Accessory systems and electronics not of Vermeer’s manufacture are warranted only to the extent of such manufacturer’s

respective Limited Warranty if any.

(14) Down hole toolage is not covered under this warranty.

(15) Wear items which are listed by product group below:

ENVIRONMENTAL:Bearing Seals, Bearings, Belts, Brake Pads, Bolts/Torqued Parts, Chain, Clutches, Clutch Components,

Curtains, Cutter Wheels, Discharge Conveyor Belts, Fuel Filters, Hammers, Hoses, Infeed Conveyor Belts, Infeed Conveyor Chains,

Knives, Oil Filters, Pockets, Rods, Rollers, Rotor Plates, Screens, Service Items, Shear Bar/Bedknife, Sprockets, Teeth, Wear Blocks,

Wear Strips, Tips, Tip Mounts, Track Chain, Track Rollers, Rubber Tracks, Rubber Grouser Bars, Rubber Track Bands, Track

Sprockets, Track Pads, Winch Cable, Windshield Wiper Parts, Lights, Antenna.

TRACK:Base Plates, Boom Wear Items, Buckets, Cable Fingers, Conveyor Belts, Clutches, Cups, Digging Chain, Digging Rims,

Drums, End Idler, Flashings, Pins and Bushings, Pivot Rings, Plastic Wear Strips, Rooter Bands, Scraper Knives, Sprockets, Teeth,

Track Chain, Track Rollers, Trench Cleaner (Crumber), Trip Cleaners, Truck Rollers, Wear Plates.

TRENCHLESS:Brushes, Clamping Vise Parts, Dies, Drive Chuck, Earth Stakes, Fan Belts, Jaws, Leaf Chain, Lights On Light

Kits, Packing Assemblies, Rod, Rod Loader Parts, Rollers, Tooling, Track Chain, Track Guides, Track Idlers, Track Pads, Track

Sprockets, Valve Seats, Wear Bars, Wear Blocks, Water Hoses, Water Swivels, Wear Bars.

UTILITY PRODUCTS: Augers, Belts, Bearings, Booms, Brake Pads, Bucket, Bushings, Chains, Clutches, Conveyor Belts, End

Rollers, Flashings, Pins, Pivot Rings, Plow Blades, Rubber Shielding, Sprockets, Teeth, Tires, Track Chain, Track Idlers, Track

Sprockets, Trench Cleaner (Crumber).

PARTS WARRANTY:

Parts replaced in the warranty period will receive the balance of the first year New Industrial Equipment Limited Warranty, during

the first (12) months or 1000 hours, whichever comes first. Replacement parts after the original machine warranty, are warranted to

be free from defects of material for ninety (90) days or the part will be repaired or replaced, without labor coverage for removal and

reinstallation.

SC362 Stump Cutter Introduction

EXCLUSIONS OF WARRANTIES: EXCEPT FOR THE WARRANTIES EXPRESSLY AND SPECIFICALLY MADE

HEREIN, VERMEER MAKES NO OTHER WARRANTIES, AND ANY POSSIBLE LIABILITY OF VERMEER

HEREINUNDER IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING, BUT

NOT LIMITED TO, ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

VERMEER RESERVES THE RIGHT TO MODIFY, ALTER AND IMPROVE ANY PRODUCT WITHOUT INCURRING ANY

OBLIGATION TO REPLACE ANY PRODUCT PREVIOUSLY SOLD WITH SUCH MODIFICATION. NO PERSON IS

AUTHORIZED TO GIVE ANY OTHER WARRANTY, OR TO ASSUME ANY ADDITIONAL OBLIGATION ON VERMEER’S

BEHALF.

NO DEALER WARRANTY. The selling dealer makes no warranty of its own and the dealer has no authority to make any

representation or promise on behalf of Vermeer or to modify the terms or limitations of this warranty in any way.

ELECTRONIC SIGNATURES. Each of the parties hereto expressly agrees to conduct transactions by electronic means.

Accordingly, the parties agree and intend that all electronic transmissions including, without limitation, electronic signatures, shall

be considered equivalent to an original writing as provided under Iowa law, as it may be amended from time to time.

MANUFACTURED BY:

VERMEER CORPORATION

Pella, Iowa 50219 USA

This page intentionally left blank.

SC362 Stump Cutter Receiving and Delivery Report i

Receiving and Delivery Report

DEALER PREP

Check or perform the following:

___ Check machine for shortage or damage in transit.

Engine

___ Check oil level of the engine, with engine level.

___ Check condition of the air cleaner.

___ Check electrolyte level of the battery.

___ Check engine for proper operation.

Hydraulics

___ Check level of the hydraulic fluid.

___ Check control levers for proper operation.

___ Check all hydraulic components for leaks or damage.

General

___ Check drive belts for proper tension.

___ Check ground drive chain for proper tension.

___ Check all shields for installation and condition.

___ Check machine for proper lubrication.

___ Check condition of all safety signs and decals.

___ Check all phases of operation.

___ Check for loose hardware.

ii Receiving and Delivery Report SC362 Stump Cutter

___ Check protective curtains for installation and condition.

___ Check tires for proper air pressure: 50 psi (340 kPa)

___ Check cutter wheel Yellow Jacket pocket bolts for proper torque: 200–215 ft-lb (271–291 Nm).

___ Check that the neutral start function operates properly

___ Check that Operator Presence system and indicator lights operate properly.

Indice

Altri manuali Vermeer Taglierina

Vermeer

Vermeer SC30TX Manuale utente

Manuali Taglierina popolari di altre marche

Milwaukee

Milwaukee HEAVY DUTY M12 FCOT Manuale utente

Makita

Makita DCS552 Manuale utente

SignWarehouse.com

SignWarehouse.com Bobcat BA-60 Manuale utente

Makita

Makita 4112HS Manuale utente

GEISMAR STUMEC

GEISMAR STUMEC MTZ 350S Manuale utente

Hitachi

Hitachi CM 4SB2 Guida alla risoluzione dei problemi

Dexter Laundry

Dexter Laundry 800ETC1-20030.1 Manuale utente

GCC Technologies

GCC Technologies AFJ-24S Manuale utente

DeWalt

DeWalt XR LI-ION DCS350N Manuale utente

Baudat

Baudat ES1 Manuale utente

Mafell

Mafell ZAF 200 Guida

Makita

Makita 4100NH Manuale utente

Formax

Formax FD 574 Manuale utente

EINHELL

EINHELL TE-MA 1500 Manuale utente

Husqvarna

Husqvarna Cut-n-Break K 760 Manuale utente

CLEAN ROOM DEVICES

CLEAN ROOM DEVICES CRD130SS Manuale utente

TRI tool

TRI tool 301A Manuale utente

Roller

Roller King 1 1/4 Manuale utente