Vermeer SC252 Manuale utente

Vermeer SC252 & SC292

Upgrade Wheel Assembly

If you have any questions or concerns, please call 1-800-473-3683

BEFORE YOU BEGIN

Read these instructions completely and

carefully

Note to installer –Be sure to leave

these instructions for the consumer’s use

Note to consumer –Keep these

instructions with your Owner’s Manual for

future reference

Skill level –Installation of the wheel

requires intermediate mechanical skills.

Proper installation is the responsibility of the

installer. Product failure due to improper

installation is not covered under any

warranty

IMPORTANT - Before you continue,

please check the packing list to make sure it

matches the contents of the boxes.

Disconnect Power

to machine to prevent any machine

components from moving before proceeding.

Failure to do so could result in death or

serious injury.

FOR YOUR SAFETY read and

observe all CAUTIONS and

WARNINGS shown throughout

these instructions. While

performing the installations that

are described in this booklet, gloves

& safety glasses or goggles should

be worn at all times.

Installation Preparation

Green Manufacturing, Inc.

9650 Packard Rd

Morenci, MI 49256

Phone 800.473.3683 • Fax 517.458.1550

TOOLS SUPPLIED:

½” Drive, ½” 6pt Impact Allen Wrench Socket

TORQUE SETTINGS:

900 Series Nut: 35ft. lbs. (47Nm)

LoPro™Bolt (lubricated with Green-Seize™): 180 to 200ft. lbs. (244 Nm)

TOOLS YOU WILL NEED:

5/8” Socket Wrench

½” Drive Torque Wrench

Green-Seize™

MANUFACTURER’S PARTS LIST:

Part Number

Description

926-WS2

900 Series Wearsharp™ 2-Sided Tooth, For Wheels 22" & Smaller

900LP-A

900 Series LoPro™ Pocket - Angle

LP-200

2” LoPro™ Bolt

ALLENWRENCH-SOCKET

½” Drive, ½” 6pt Impact Allen Wrench Socket

Table of Contents

Assembly Instructions........................................................................ 4

Upgrade Assembly Diagram............................................................... 7

Greenteeth® Guarantee..................................................................... 8

Material Safety Data Sheet ................................................................ 9

Assembly Instructions

1. Locate the pocket set with straight pockets on your wheel. Make sure to refer to the Upgrade

Assembly Diagram found on page 7 for the next 28 steps.

2. Remove one set of straight pockets (Notice you will be leaving this area blank).

3. Proceed to the pocket set below the removed pocket set in step 2. This should be an angle

pocket set.

4. Remove the one set of angle pockets (Notice you will be replacing this pocket set with an angle

pocket set).

5. Clean both sides where the pockets contact the wheel, with a wire brush. Be sure to remove

all dirt and debris so the pocket is seated tightly against the wheel.

6. Apply Green-Seize™ to the threaded end of two LoPro™ bolts.

7. Starting with the angle pocket install a LoPro™ bolt into the

counter-bored hole and then do the same of adjacent pocket

of that set.

8. Slide the LoPro™ bolts through the empty holes in the wheel

and thread them into the adjacent pocket’s threaded holes.

For now, firm up the LoPro™ bolts until pockets are seated.

(Figure 1.1)

9. Proceed to the pocket set below the new pocket set installed

in step 8. This should be an angle pocket set.

10. Remove the one set of angle pockets (Notice you will be

leaving this area blank).

11. Proceed to the pocket set below the removed pocket set in step 10. This should be an angle

pocket set.

12. Remove the one set of angle pockets (Notice you will be replacing this pocket set with an angle

pocket set).

13. Clean both sides where the pockets contact the wheel, with a wire brush. Be sure to remove

all dirt and debris so the pocket is seated tightly against the wheel.

14. Apply Green-Seize™ to the threaded end of two LoPro™ bolts.

15. Starting with the angle pocket install a LoPro™ bolt into the counter-bored hole and then do

the same of adjacent pocket of that set.

16. Slide the LoPro™ bolts through the empty holes in the wheel and thread them into the

adjacent pocket’s threaded holes. For now, firm up the LoPro™ bolts until pockets are seated.

(Figure 1.1)

17. Proceed to the pocket set below the new pocket set installed in step 16. This should be a

straight pocket set.

Figure 1.1

18. Remove the one set of straight pockets (Notice you will be leaving this area blank).

19. Proceed to the pocket set below the space left empty in step 18. This should be an angle pocket

set.

20. Remove the one set of angle pockets (Notice you will be leaving this area blank).

21. Proceed to the pocket set belowthe space left empty in step 20. This should be an angle pocket

set.

22. Remove the one set of angle pockets (Notice you will be replacing this pocket set with an angle

pocket set).

23. Clean both sides where the pockets contact the wheel, with a wire brush. Be sure to remove

all dirt and debris so the pocket is seated tightly against the wheel.

24. Apply Green-Seize™ to the threaded end of two LoPro™ bolts.

25. Starting with the angle pocket install a LoPro™ bolt into the counter-bored hole and then do

the same of adjacent pocket of that set.

26. Slide the LoPro™ bolts through the empty holes in the wheel and thread them into the

adjacent pocket’s threaded holes. For now, firm up the LoPro™ bolts until pockets are seated.

(Figure 1.11)

27. Proceed to the pocket set below the new pocket set installed in step 26. This should be an

angle pocket set.

28. Remove the one set of angle pockets (Notice you will be leaving this area blank).

29. Install your teeth with the carbide facing down. The

shoulder of the tooth will meet the flat indent of the

pocket and the tooth will not rotate. Insert spacer

over shank Chamfer down then thread one of the

lock nuts onto the top portion of the tooth. Hand

tightening is good for now. Repeat until all teeth are

installed. (Figure 1.2)

30. Make sure the pockets are seated on the wheel and

the bolts are seated in the pockets. Continue

tightening your LoPro™ bolts until they are all

torqued to 180-200 foot lbs. (244 Nm).

31. Before torqueing your tooth down, first make sure that the tooth is seated properly in

the pocket. Then tighten the top nut until the tooth is firmly seated and torqued to

35 ft. lbs. (47 Nm). You may need to hold the tooth in place. Repeat until all teeth are

properly torqued.

Over-tightening the nut will stretch the threads and degrade the fasteners ability to retain the tooth.

Figure 1.2

32. Once all pockets and teeth are torqued properly start the machine engine and engage the

wheel.

33. Ensure there are no noises emanating from the upgrade installation.

Upgrade Assembly Diagram

GREENTEETH™ GUARANTEE

NEW SETUPS AND FIRST TIME CUSTOMERS:

If you purchase a Greenteeth® setup and are not completely satisfied with its performance, please

contact Green Manufacturing at 800.473.3683 to request a return authorization within 30 days of

purchase date for a product refund or exchange.

PRODUCT QUALITY:

We strive to provide exceptional quality product. Our products undergo a stringent quality control

process, however if you feel that there is an issue with the quality of your product, please contact Green

Manufacturing at 800.473.3683 immediately. We will accept unused parts for return or exchange for up

to 30 days from the date of purchase with proof of purchase included with the return.

Greenteeth® is proudly manufactured in the USA by Green Manufacturing, Inc.

Green Manufacturing, Inc.

9650 Packard Rd

Morenci, MI 49256

Phone 800.473.3683 • Fax 517.458.1550

MATERIAL SAFETY DATA SHEET

I - PRODUCT IDENTIFICATION

Trade Name: Tungsten Carbide Chemical Family: Refractory Metal Alloy

Chemical Formula: WC CAS#: 12070-12-1

II - HAZARDOUS INGREDIENTS

Hazardous Components % OSHA/PEL ACGIH/TLV Sec. 302 Sec. 304 Sec. 313

Tungsten Carbide 0-100 N/E N/E No No No

Tungsten compounds 0-100 5 mg/m3 C - 1 0 mg/m3 No No No

HM IS Ratings (0-4): Health: 3 Flammability: 0 Reactivity: 0

HM IS Protective Equipment: H: glasses, gloves, clothing, combo respirator

III - PHYSICAL DATA

Boiling Point: 6000 oC Melting Point: 2820 - 2940 oC

Evaporation Rate: N/A % Volatiles: N/A

Solubility in H2O: Insoluble Vapor Pressure: N/A

Vapor Density: N/E Specific Gravity: 13.6 gm/cc at 18 oC

Appearance and Odor: Grey to black powder, odorless Molecular Weight: 195.86

IV - FIRE AND EXPLOSION HAZARDS DATA

Flash Point: N/A Flammability: Non-Flammable

Explosive Limits: Lower: N/A Upper: N/A

Extinguishing Media: Use suitable extinguishing media for surrounding materials and type of fire.

Special Fire Fighting Procedures: Firefighters must wear full face, self-contained breathing apparatus with full

protective clothing to prevent contact with skin and eyes. Fumes from fire are hazardous. Isolate runoff to prevent

environmental pollution.

Unusual Hazard: Dusts may present a fire or explosion hazard under rare favoring conditions of particle size,

dispersion, and strong ignition source. However, this is not expected to be a problem under normal handling

conditions.

V - HEALTH HAZARD INFORMATION

Routes of Entry: Inhalation, ingestion, skin or eye contact (for dusts, mists, powder, and fume).

Effects of Overexposure: Industrially tungsten does not constitute an important health hazard. Expo sure is related

chiefly to the dust arising out of the crushing and milling operations. Chronic inhalation of the dust may cause lung

damage in humans. Heavy exposure to the dust or the large amounts of the soluble compounds produces changes

in body weight, behavior, blood cells, choline esterase activity and sperm in experimental animals.

Acute Effects:

Inhalation: Toxic by inhalation. May cause irritation to the mucous membranes, coughing, dyspnea, soreness in

the chest, weight loss, hemoptysis, bronchitis, asthma, pulmonary fibrosis and radiological changes in the lungs.

Ingestion: May cause irritation to the gastrointestinal tract and diarrhea.

Skin: May cause irritation.

Eye: May cause irritation.

Chronic Effects:

Inhalation: May cause damage to the lungs.

Ingestion: No chronic health effects recorded.

Skin: May cause dermatitis, sensitization and eczema.

Eye: May cause conjunctivitis.

Medical Conditions Generally Aggravated by Exposure: Pre-existing respiratory and skin disorders.

Target Organs: May affect the respiratory system.

Carcinogenicity: NTP: No IARC: No OSHA: No

EMERGENCY AND FIRST AID PROCEDURES:

INHALATION: Remove victim to fresh air. Keep warm and quiet, give oxygen if breathing is difficult and seek

medical attention.

INGESTION: If conscious, give 1-2 glasses of milk or water and induce vomiting (Never induce vomiting or give

anything by mouth to an unconscious person). Seek medical attention.

SKIN: Remove contaminated clothing from affected area, brush material off skin. Wash affected area with mild

soap and water. Seek medical attention if symptoms persist.

EYE: Flush eyes with lukewarm water, lifting upper and lower eyelids, for at least 15 minutes. Seek medical

attention if symptoms persist.

VI - REACTIVITY DATA

Stability: Stable

Conditions to Avoid: None

Incompatibility (Material to Avoid): Chlorine, fluorine, nitrogen dioxide, nitrous oxide, iodine pentafluoride and

lead oxide.

Hazardous Decomposition Products: None recorded.

Hazardous Polymerization: Will not occur

VII - SPILL OR LEAK PROCEDURES

Steps to Be Taken in Case Material Is Released or Spilled: Wear appropriate respiratory and protective equipment

specified in Section VIII. Isolate spill area and provide ventilation. Vacuum up spill using a high efficiency

particulate absolute (HEPA) air filter and place in a closed container for proper disposal. Take care not to raise

dust.

Waste Disposal Method: Dispose of in accordance with all local, state, and federal regulations.

VIII - SPECIAL PROTECTION INFORMATION

Respiratory Protection: NIOSH approved dust, mist, and vapor cartridge respirator.

Ventilation: Use local exhaust ventilation which is adequate to limit personal exposure to airborne dust levels

which do not exceed the appropriate PEL or TLV. If such equipment is not available, use respiratory protection as

specified above.

Protective Gloves: Rubber gloves.

Eye Protection: Safety glasses.

Other Protective Clothing or Equipment: Protective gear suitable to prevent contamination.

IX - SPECIAL PRECAUTIONS

Precautions to Be Taken in Handling and Storage: Store in a tightly sealed container in a cool, dry, well-ventilated

area. Wash thoroughly after handling.

Other Precautions: Implement engineering and work practice controls to reduce and maintain concentration of

exposure at low levels. Use good housekeeping and sanitation practices. Do not use tobacco or food in work area.

Wash thoroughly before eating or smoking. Do not blow dust off clothing or skin with compressed air.

The above information is believed to be correct, but does not purport to be all inclusive and shall be used only as a

guide. Green Manufacturing, Inc. shall not be held liable for any damage resulting from handling or from contact

with the above product.

Altri manuali per SC252

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Vermeer Macinacaffè

Vermeer

Vermeer SC252 Manuale del proprietario

Manuali Macinacaffè popolari di altre marche

Parkside

Parkside PWS 230 C3 Manuale utente

SUHNER ABRASIVE

SUHNER ABRASIVE ASC 9 Manuale tecnico

PTA

PTA P1322 Manuale utente

Crown

Crown CT13313 Manuale utente

Parkside

Parkside 280250 Manuale utente

Climax

Climax VM2150 Series Manuale utente

Jet

Jet JPSG-618M1 Manuale di servizio

Makita

Makita GA4030 Manuale utente

DeWalt

DeWalt DWEN202 Manuale utente

Grizzly

Grizzly G2790 Manuale utente

Fein

Fein MSf843-1a Manuale utente

Bosch

Bosch GWS 14,4 V PROFESSIONAL Manuale utente

RAMSET

RAMSET CBAGR18 Manuale utente

Bosch

Bosch 8-115 Z Manuale utente

STEELE PRODUCTS

STEELE PRODUCTS SP-PB008 Manuale utente

MW TOOLS

MW TOOLS ME15W Manuale utente

Caravaggi

Caravaggi SP 20 Istruzioni operative

SUHNER ABRASIVE

SUHNER ABRASIVE UWK 10-R125 Manuale tecnico