Vertiv Geist PFS-100 Manuale utente

GEIST™ POWER FAILURE SENSOR

Quick Installation Guide

VM1055/590-2254-501A 1

Part Number:

PFS

Description

The Power Failure Sensor (PFS) is

used to monitor voltage presence

(grid/city power) on a circuit

through the I/O ports of a remote

environmental or power +

environmental monitor. If voltage

drops to zero, the monitored I/O

reading drops below 10.

NOTE: To monitor the loss of ‘grid-

supplied’ power, connect the

PFS-100 directly to that power

source before any UPS systems.

NOTE: In order to monitor and

report the PFS signal state during a

power loss, the remote monitoring

unit itself, as well as any switches

or routers within the data path of

the unit, must be backed up by

UPS power. If any of these units

lose power during a power outage,

appropriate remote alarm reporting

cannot take place.

Installation

1. Using only an approved AC

adaptor, plug the adaptor into

the desired ‘grid-supplied’

power location. Do not plug the

adaptor into the PFS-100

sensor body yet.

2. Route the sensor body wire

with the two stripped ends to

the remote monitoring unit.

Connect the ends to the I/O

port on the remote monitoring

unit. The solid black wire

connects to Common (-) and

the striped black wire connects

to the desired Input (1, 2 or 3).

3. Plug the approved AC adaptor

into the PFS-100.

NOTE: During initial setup, one

PFS-100 LED turns on and one

flashes for approximately 35

seconds. After that time, a third

Power Failure Sensor

GeistTM Power Failure Sensor

SPECIFICATIONS

Sensor Input Output

PFS-100 4.5-6 VDC 3.4-5 VDC

Power Adaptor Input Output

PFS-100 US, PFS-100 UK,

PFS-100 UN 100-240 VAC 50/60 Hz 6 VDC

GeistTM Power Adaptor Options

PFS-100 US

PFS-100 UK

PFS-100 UN

To contact Vertiv Technical Support: visit www.VertivCo.com

trademarks or registered trademarks of their respective owners. While every precaution has been taken to ensure accuracy and completeness herein, Vertiv Co. assumes no

responsibility, and disclaims all liability, for damages resulting from use of this information or for any errors or omissions. Specifications are subject to change without notice.

GEIST™ POWER FAILURE SENSOR

Quick Installation Guide

2 VM1055/590-2254-501A

LED turns on and the flashing

LED stays solid on, indicating

that the sensor is ready.

4. Use the remote monitoring unit

to test the sensor. With the

PFS-100 plugged in, the I/O

reading is >50. When the

PFS-100 is unplugged or the

circuit loses power, this value

drops below 10.

5. On the remote monitoring unit,

click the Configuration icon,

change the sensor label and

click Save. Complete this step

before installing additional

sensors.

6. As data is analyzed over time,

you can determine steady state

conditions and set alarms

accordingly.

Power Failure Sensor

GeistTM PFS-100 Wiring Configuration

Remote monitoring unit

Analog Inputs

C 1 2 3 C

Power source to

be monitored

PFS-100

power

adaptor

PFS-100

Black Black

striped

Questo manuale è adatto per i seguenti modelli

Altri manuali Vertiv Accessori

Vertiv

Vertiv SmartRow DCR Istruzioni di installazione e manutenzione

Vertiv

Vertiv GEIST SwitchAir SA1-02005 Manuale utente

Vertiv

Vertiv GEIST SwitchAir SA2-002 Manuale utente

Vertiv

Vertiv Liebert CRV CCD10 Manuale utente

Vertiv

Vertiv Liebert CRV Guida utente

Vertiv

Vertiv Liebert THW420 Istruzioni per l'installazione

Vertiv

Vertiv OC 4020009 Manuale utente

Vertiv

Vertiv Liebert Mini-Mate2 Manuale utente

Vertiv

Vertiv GEIST SwitchAir SA2-003 Manuale utente

Vertiv

Vertiv Liebert DSE500 Istruzioni di installazione e manutenzione

Vertiv

Vertiv GEIST SwitchAir SA2-004 Manuale utente

Vertiv

Vertiv Liebert Xtreme Density Series Guida

Vertiv

Vertiv Liebert CRV300 Manuale dell'operatore

Vertiv

Vertiv VRC-S Manuale utente

Vertiv

Vertiv Liebert CRV Istruzioni di installazione e manutenzione

Vertiv

Vertiv GEIST SwitchAir SA1-03001 Manuale utente

Vertiv

Vertiv GEIST SwitchAir SA2-006 Manuale utente

Manuali Accessori popolari di altre marche

Hillco

Hillco 2810 Manuale utente

Siemens

Siemens QSA2700D Manuale dell'operatore

Contours

Contours ZY024 Manuale utente

Saivod

Saivod VS621 Manuale utente

Virtuox

Virtuox VirtuCLEAN 2.0 Manuale utente

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuale utente

Z-Wave

Z-Wave HSD-200Z Manuale utente

turck

turck FMX-IM-2UPLI63FX Manuale utente

Decagon Devices

Decagon Devices 10HS Manuale utente

UPPAbaby

UPPAbaby Cup Holder Manuale utente

Elko

Elko SmartSensor Leakage Wireless Manuale utente

Grizzly

Grizzly H8371 Manuale utente

Panasonic

Panasonic HG-T Series Manuale utente

IFM Electronic

IFM Electronic Efector 250 Series Guida di riferimento

DigiDesign

DigiDesign 888/24 I/O Manuale utente

PROZIS

PROZIS QUAY Manuale utente

patagonia

patagonia PSI Vest Manuale utente

SFC Energy

SFC Energy EFOY GO! Manuale utente