Vetta C350 Manuale utente
1
CYCLE COMPUTER OWNER'S MANUAL
ENGLISH
2
INTRODUCTION
Congratulations on your purchase of the new Vetta C-350 cycle computer. The C-350 is designed for the
cycling enthusiast with the features that support a serious training program, whether you are a road cyclist,
offroad cyclist, or triathlete. The Vetta two button design allows for easy programming and
operation. This C-350 model model offers seven functions, including elapsed time, average and maximum
speed, and trip distance. The wireless feature of the C-350 keeps the lines of your bike clean and free of
wires and helps to make installation a snap.
COMPONENT ILLUSTRATIONS
Head Unit Wireless Sensor
and Bracket
Bracket Battery MagnetTransmitter
Battery
3
FUNCTION LIST
SPEEDOMETER (S) (Mile/h or km/h)
Tells you your current speed on the upper line of the display screen at all times.
CUMULATIVE ODOMETER (O)
Tells you your cumulative distance until you perform an all clear total reset, the
battery is changed, or the unit passes 9999.9 mi. or km.
TRIP ODOMETER (D)
Tells you the distance for your current ride from 0 to 999.99 mi. or km. Automati-
cally resets after 999.99 mi. or km. Trip odometer will commence automatically
when the bicycle wheel rotates. To reset the trip odometer to zero at the end of your
ride, press the “SET” and “MODE” buttons simultaneously.
ELAPSED TIME (T)
Elapsed time begins when the wheel begins to rotate. It starts automatically
4
when the wheel is set into motion and stops when the wheel stops for over
four seconds. When one hour of riding time has elapsed, the clock display will
automatically display the time as hours and minutes. When ten hours of rid-
ing time have elapsed, the clock will return to 0:00:00. Average speed will
show an “E” for error. Distance (D) and maximum speed (M) will continue to
accumulate. To clear the elapsed time press the “SET” and “MODE” buttons
while in the elapsed time mode.
MAXIMUM SPEED (M)
Maximum speed is your highest attained speed on your current ride. It is stored
and displayed until an all clear reset is performed or the battery changed.
AVERAGE SPEED (A)
Your average speed is calculated using your true ride time and trip distance. The
minimum unit displayed is 0.1 km/h or mile/h.
5
DIGITAL 12/24 HOUR CLOCK
Gives you the time of day in a 12 or 24 hour format. To display the clock, press the
“MODE” button for one second. To change between the 12 and 24 hour clock, press the
“MODE” button for three seconds while in the clock mode. Press the “MODE” button
again to return to odometer mode.
6
RESETTABLE ODOMETER
The cumulative odometer on the C-350 can be preprogrammed to any desired mileage. This feature allows
you to retain your cumulative mileage when replacing batteries or allows you to lie about your mileage to
impress your friends.
AUTO POWER SAVING MODE (AUTO START-STOP)
As a battery saving device, Vetta computers will automatically shut down after 10 minutes of non-use. Your
C-350 will automatically restart itself as soon as the unit receives input from the wheel.
AUTO SCAN
Once it is activated, this feature scans all display modes at 3 second intervals. To activate this feature, press
the “SET” button while in the trip distance mode. To deactivate the Auto Scan mode press either the “SET”
or “MODE” button.
ALL CLEAR TOTAL RESET
To completely clear the unit of all information, press the “SET” and “MODE” buttons for 10 seconds. The
unit will return to the programming mode with the flashing km/h symbol displayed. The unit is now ready
to reprogram. Do not clear the computer unless you need to reprogram the unit.
FEATURE LIST
7
The C-350 computers use a common LR44 1.5v button cell battery. Replacement
batteries are available at most camera shops and from your Vetta retailer. Under
normal usage a battery should last approximately one year.
NOTE: Most prob-
lems that occur with cycle computers are caused by dead or weak batteries. If
you are having problems with your computer's operation, check and replace the
battery first.
STEP 1
Remove the battery cover from the bottom of the computer by turning the
battery cap counterclockwise with a coin.
STEP 2
Install the battery into the battery compartment with the positive (+) side of the
battery facing the compartment door. Be careful when you are installing the
battery not to bend any of the battery contacts.
STEP 3
Screw the battery cap firmly into place. Make sure that the rubber o-ring seal
does not get pinched or distorted in this operation as this may compromise the
waterproofing of the unit.
BATTERY INSTALLATION
LR44 1.5v Battery
8
CR2032 3v Battery
INSTALLATION OF TRANSMITTER BATTERY
The transmitter comes from the factory with the CR2032 3v battery installed.
STEP 1
To replace the battery, first remove the battery cap on the top of the transmitter
with a coin. Remove the old battery and dispose of properly.
NOTE: Check the
inside of the transmitter for corrosion. If corrosion is visible, replace the
transmitter with a new unit.
STEP 2
Install a new battery in the transmitter battery compartment with the positive (+)
side facing the opening and reinstall the battery cap.
Make sure that the battery cap is tight to prevent moisture from
entering the transmitter unit. An improperly installed battery can damage the
transmitter.
CAUTION
9
WARNINGS AND CAUTIONS
Vetta encourages you to ride safely. Wear a helmet every time you ride, use front and rear
lights at night, and always keep your eyes on the road ahead of you.
Vetta cycle computers are sophisticated electronic instruments. Vetta recommends that this
product be installed only by a qualified bicycle retailer. Failure to read these instructions and improper
installation of this device may void the warranty. If you are in doubt about any aspect of the installation
or operation of this product, consult your local bicycle retailer for clarification.
CAUTION
CAUTION
“SET” BUTTON (LEFT)
The “SET” button confirms, resets, or clears numbers.
“MODE” BUTTON (RIGHT)
The “MODE” button starts, stops, or moves in a loop sequence from one function
to another.
BUTTON FUNCTIONS
10
SETTING MILES/HOUR OR KILOMETERS/HOUR
After the battery is installed, all of the displays will be illuminated. km/h will then
appear on the screen.
STEP 1
Press the “MODE” button to switch between miles and kilometers.
STEP 2
When your selection has been made, press the “SET” button to confirm your
selection and move to the wheel circumference selection mode.
PROGRAMMING THE COMPUTER HEAD
Now that you are familiar with the features of your Vetta C-350 cycle computer, you are ready to begin pro-
gramming the unit specifically for your bike. Take a few minutes to familiarize yourself with the buttons and
their functions before you proceed to program the unit.
Indice
