VFTech GNOM Super PRO Manuale utente

Underwater remotely
operated vehicle for inspections
GNOM Super PRO
Operators manual
VFTECH s.r.o.
Vapenicka 24, 971 01 Prievidza, Slovakia
Tel/Fax +421 46 54264 56
http://www.vftech.sk

v03/2017
2
TABLE OF CONTENTS
Warning !!!
Voltage on cable 180VDC!
Do not touch the cable in a water during operation!
If any damages happen on a shield of cable it must be repaired or
changed !
Attention! AC power maximum 240V !
1. Description 3
1.0 Introduction 3
1.1 Purpose 4
1.2 Design 5
1.3 Technical specifications 7
2. User’s manual for operation with GNOM 8
3. Keys and Buttons at the control panel 14
4. Screen modes 17
5. Calibration 18
6. Maintenance operation 19
7. Safety requirements 20
8. Warranty statement 21
9. Examples of linking modules 22
10. Appendix 23

v03/2017
3
1. DESCRIPTION
1.0 INTRODUCTION
ВНИМАНИЕ!
Warning!
Achtung!
ELECTRIC DANGER 230V/50Hz
Read carefully this instruction
Ask for assistance of a qualified electricians
Underwater remotely controlled vehicle GNOM is connected to AC 230 V / 50 Hz power supply and
poses a potential hazard (electric shock or fire).
Underwater vehicle "GNOM" belongs to the category of electromechanical products.
Installation, operation and maintenance of these products must be performed by qualified and
competent persons, acquainted with this user manual.
Buyers and attendant facilities "GNOM" must abide operating instructions to ensure their own
safety, the safety of people around and to minimize the risk of potential damage of the module
when working under water.
The guide should always be available to all persons involved in organization and implementation of
operations with the GNOM modules.
Unless the assembly GNOM is used according to manual, then it meets international standards:
Safety IEC 60065 (GOST R IEC 60065-2002)
Electromagnetic compatibility IEC 61000-6-1-99 (GOST R 51317.6.1, GOST R 51317.6.3-99)
In addition to these general principles, the laws and regulations applicable in each country as well as
the rules and regulations applicable at the place of work with the underwater modules should be
respected.
Sale or transfer of module "GNOM" to the other person may be exercised only with delivery of
operating instructions. In this case the potential risks in the operation of the gnome passes to the
buyer (attendants).
This guide GNOM together with operating instruction is intended to inform the user in order to
ensure correct and safe use of GNOM.

v03/2017
4
1. DESCRIPTION
1.1 PURPOSE
The product "GNOM" is designed for underwater works. Inspection and control of premises
located under water in coastal and inland waters, as well as in the control of reservoirs and
water works.
The main advantage of remotely operated vehicle is that you can see underwater full-
featured video
Command of underwater module is executed by operator from the shore (or the vessel) by
means of the control module, which is a part of the kit.
The modern computer and telecommunication technologies are used in the device, and
made it easy in handling, compact, light and inexpensive.
These solutions allowed to use thin (only 10 mm diameter) and flexible communication
cable for transmission data, power and video signals to/from vehicle. The special Kevlar
threads have been used to improve the cable's tensile strength. Because of this fact, the
device keeps the highest degree of stabilization what is very important for inspections. The
vehicle has a good maneuverability and can easily turn on the spot.
High-effective electric motors with magnetic couplings and hi-tech electronics are used in
the vehicle, provide the fast speed of the GNOM with low power consumption.
One of the most important features of this device is a possibility to operate it from PC and
via Lan/Internet.
The GNOM, in essence, an underwater helicopter with the video-camera which moves in
any direction according to the operator's instructions.
For update info please visit our web site www.vftech.sk

1.2 DESING
ROV GNOM S
uper PRO
1 – ROV GNOM Super PRO
, 2
ROV GNOM S
uper Pro
1 – ROV GNOM Super PRO
2 – Control box with joystick
3 – Hand reel with tether
4 – Joystick
5 – LCD monitor
WARNING:
Producer reserves the right to change the scope of delivery with
maintaining the functionality and technical specifications for
sets
Main features
Color High Resolution video
3 (5)
thrusters, adjustable speed
Slow/fast mode, tilting vehicle mode
LEDs lights
Flexible thin cable
Device is fitted out with the depth gauge, autodepth mode
Heading (co
mpass), autoheading
Videotext overlays with graphics
On screen menus
Easy game joystick control
Digital data channel
PC interface, Lan/Internet web video/control (option)
All packed in 2 cases, hand carried
v03/2017
1. DESCRIPTION
uper PRO
full complete set + options
, 2
– Control box waterproof case integrated, 3 –
hand reel with sleep ring, 4
5 –LCD monitor 15", 6 – grabber
uper Pro
basic complete set
WARNING:
Producer reserves the right to change the scope of delivery with
maintaining the functionality and technical specifications for
Color High Resolution video
-
camera with tilt servo and digital zoom
thrusters, adjustable speed
Slow/fast mode, tilting vehicle mode
Device is fitted out with the depth gauge, autodepth mode
mpass), autoheading
Videotext overlays with graphics
Easy game joystick control
Digital data channel
PC interface, Lan/Internet web video/control (option)
All packed in 2 cases, hand carried
5
full complete set + options
hand reel with sleep ring, 4
– joystick,
camera with tilt servo and digital zoom

v03/2017
6
1. DESCRIPTION
1. Polypropylene frame
2. Main hull section
3. Horizontal thrusters
4. Laterial thrusters
5. Vertical thrusters
6. Flotation blok
7. Sector sonar
8. MicroNAV
9. Lights
10. Manipulator
11. Camera
The system consists of the GNOM underwater vehicle, reel with cable and power supply unit.
Underwater module is protected by polypropylene frame , two waterproof metal casings (hulls) ,
terminated by transparent windows for video cameras (front and rear).
Power modules, control electronics, compass and pressure sensor are mounted inside casings.
The underwater module is powered by five thrusters, fixed to the frame: two horizontal , the two lateral ,
and one vertical .
On the frame can be installed LED light (the number of LEDs can be varied), the manipulator ⑩, a circular
sector-Sonar .
To ensure buoyancy near neutral buoyancy a float is attached on the frame .
The underwater unit is connected to the control unit with cable which ensure supply of underwater unit ( 180
V), the information from the sensors and video signal from video camera.
The tether is on reel with the slip rings what ensure that you can wind /unwind the cable during operation.
The cable is reinforced with Kevlar fiber to increase the mechanical strength.
The power supply/control module is stored in another waterproof case and consists of a power module and
control electronics. In the case there is also integrated 15 "monitor. On display you can see video pictures of
the underwater module.
On demand it is possible to supplement the system with a video grabber to record a video that you can watch
on the monitor and analyze afterward.

v03/2017
7
1. DESCRIPTION
1.3 TECHNICAL SPECIFICATION
Speed:
horizontal motion, up to 4.0 m/s
vertical motion, up to 0.5 m/s
(above numbers depend on a length of pooling cable)
Max operating depth 150 m ( option 500m )
Power voltage 100-230VAC
Operating temperature range from -5…+45°C
Operating environment humidity, up to 100%
Weight of the vehicle 15 kg
Full weight of the system 45 kg
Dimensions of vehicle 450x300x280mm
Cable:
diameter 10 mm
length up to 200m ( option 500 m )
Tensile strength - 200 kg, damage to function of comes at a force of larger than 50 kg.
Options:
Rear camera with LEDs (color or b/w with IR lights)
Additional lights
Laser pointers
Grabber
Slip ring cable reel
LCD 8-15" built in case
Sector sonar Micron, Tritech
MicroNAV

v03/2017
8
2. USER’S MANUAL FOR OPERATION
Requirements for location and climatic conditions of use
2.1 Conditions and procedure operation at aplication site should minimize the risk of dangerous situations
and possible damage of underwater module GNOM during all work time.
Electrical socket, control unit and cable assemblies (reel) must be protected:
• from direct exposure to precipitation (rain, snow, dew)
• from harmful effects by animals, rodents and insects
• from fall in water and immersion in water
• from the careless treatment of other person
NOTE: If the ambient temperature exceeds + 20 ° C, the control unit must be protected against overheating
by solar radiation.
2.2 At the first signs of impending storm is required to cease immediately underwater operations and unplug
the device from power supply (socket).
It is forbidden to keep the device connected to electricity after termination of work. After end of work always
remove the power plug from the outlet.
2.3 Gnome is designed for use in following climatic conditions:
• air temperature: from -20 ° C to 45 ° C;
• Relative humidity (non-condensing): max 98%
• Atmospheric pressure, mm Hg. : From 630 to 800
2.4 The communications between control unit and underwater module via cable is guaranteed at air
temperature from -- 20 ° C to +45 ° C and a water temperature of -5 ° C to +45 ° C.
2.5 Electrical Characteristics
2.5.1 Supply voltage 230 VAC, 50 Hz.
Power / control module operates in the range of supply voltage from 198V ~ to ~ 242v
2.5.2 Total consumption for "GNOM" depends on the configuration of assembly et does not exceed 2000W.
2.5.3 Supply voltage in network must be in compliance with specification GOST 13109-97 and allowable pulse surges
from lightning and other switching phenomena refers to category II (up to 2.5kV)
2.5.4 Connection of kit GNOM to network (source) is made via three-wire power cable.
CAUTION:
A network cable is included in delivery kit.
Never substitute cable by another cable with unknown parameters, respectively without its control!
2.5.5 Power of underwater module is realized from power / control module assembly. Supply voltage of underwater
module is 180 V DC. The module is connected to the power supply via the cable (10 mm) which comes on the reel.
Operating current of underwater module is not higher than 10A.

v03/2017
9
2. USER’S MANUAL FOR OPERATION
The characteristics and a security parameter
2.6.1 Mode of protection against electric shock from the electrical power supply in 1st Class is guaranteed by
following measures:
- Reinforced insulation, power module mounted in plastic waterproof case
- Protection of "grounding" of all conductive parts through PE conductor in AC power module cable
- Mains fuse in interior of the power / control module – on the phase conductors.
2.6.2 Parameters of insulation between conductors of connector module (connected in parallel) and exposed
metal housing parts:
- Insulation resistance at least 20 MOhm at voltage of 500 V DC - measured at relative air humidity 75% and
temperature between + 16
C and + 24
C
- Electric strength - not less than 2120 V DC.
2.6.3 resistance between PE-pin socket module and metal parts of the module - no more then 0.1 Ohm at
current charge 25A.
2.6.4 Another mode of protection against electric shock is to use a earth-leakage breaker in the route of the
line voltage 230V.
Residual current device provides two-pole disconnect of underwater module under partial or total damage of
insulation. Fault current for protection of live parts is 30 mA.
2.6.5 Major critical module components that provide functions against electric shock include:
- AC power cable to the power / control unit
- Fuses
- Plug the AC filter
- Earth-leakage breaker
- The residual current device
- Power - communications cable (between underwater module and power / control module)
WARNING: Replacement of critical components is permitted only for the types mentioned in the
documentation of GNOM and with a valid certificate from the manufacturer.
Measures to ensure security in preparation for the work and operation with GNOM
Classification of persons who may handle with electrical product.
Classification of persons referred to in accordance with the recommendations based on IEC International
Electrotechnical Vocabulary (IES), IEC 61140, IEC 60065.
Qualified person (specialist) - a person who has appropriate education and work experience, allowing him to
avoid and exclude the risk that electrical equipment may create (IES 826-09-01).
Educated person - a person who has undergone specialized training for work on a specific device in
accordance with safety regulations.
Instructed person - a person who has been briefed with the device using or operating under the supervision of
a qualified person which allows to avoid danger and eliminate risks that electrical equipment may create (IES
826-09-02).
Simple person - a person who is neither a qualified person nor an instructed person (IES 826-0903).
Operator - a person performing work at the production facilities in line with its purpose, operating

v03/2017
10
2. USER’S MANUAL FOR OPERATION
instructions and is a qualified, trained or instructed person.
Unauthorized person - a person invited or bystanders.
CAUTION!
To minimize the risk of damage the modules "Gnom" and unsafe situations, do not let children, mentally unstable or
extremely behaving persons operate the underwater module.
2.7.1 Connection to the electricity network 230V
The electrical outlet to which you connect GNOM, or extension cable with splitters, must be completely intact and
construction-technically compatible.
A1: Supply voltage 230V AC for additional devices must be made only by means of a cord with power strips in
accordance with the requirements and restrictions specified in the instruction manual.
A2: WARNING!
By working directly with underwater module it is forbidden to connect to a power strip any heating and lighting
equipment as well as various power tools.
Compliance with the requirements of paragraphs A1, A2 ensure the preservation of security and improvement of
electromagnetic compatibility system.
2.7.2 WARNING!
You can not connect to the GNOM and other devices (accessory) to the mains with the following problems:
• Wrong - incorrect wire connections L and N conductors in the appropriate slot.
• without protective earthing conductor.
Note. Checking the correct wiring connections (phase conductor - L) inspects the operator. (E.g. by phase tester)
2.7.3 WARNING!
It is not allowed to repeatedly turn on and off line voltage 230 V at intervals shorter then 5 seconds.
2.7.4 Before starting work as well as during operation, it is necessary to carry out a performance test to detect any
defects reducing the level of safety equipment.
Check:
- Damage (wearing) of contacts, insulators and conductors power cords.
- Increased heating or overheating of connectors insulating material.
2.7.5 Identification and removal of defects in paragraphs 2.7.2 and 2.7.3 should be carried out in the presence of a
qualified person.
2.7.6 Checking the Residual current device
Carry out before any underwater operation at the new location as follows:
• If the requirements of paragraph 2.7.1 are met and connect to the power supply only power module
• Switch on mains voltage button on the control panel
• After 5 seconds press the "TEST" button on the residual current device. It would immediately lead to a safe shutdown
of module
• Switch off the mains voltage button on the control panel. Switch on the current circuit breaker
• Again switch on the power supply button on the control panel. Residual current device must remain switched on.
Indice
Altri manuali VFTech Strumento analitico


















