Vibe OPTIVWT5-V8 Guida alla configurazione

OPTIVWT5-V8

OPTI8VWT5-V0

OPTI8VWT5.1-V0

Volkswagen Transporter T5 & T5.1 (2003-2015)

OPTIVWT6-V9

OPTI8VWT6-V0

Volkswagen Transporter T6 (upto 2019)

OPTIVWT6.1-V0 6.5”VERSION ONLY

VEHICLE SPECIFIC AUDIO UPGRADES

High Efficiency OEM Speaker System

Introduction

Volkswagen Transporter T5 & T5.1 (2003-2015)

Volkswagen Transporter T6 & (2015-2019)

Volkswagen Transporter T6.1 (upto 2019) –6.5”ONLY

This VIBE Optisound speaker kit has been specifically designed as a direct speaker and

tweeter upgrade for the Volkswagen T5 & T5.1 & T6 & T6.1

Using super-efficient speaker technology combined with everything you need in one box,

upgrading your speakers and getting a massive improvement in sound and performance

couldn’t be easier. The kit includes all installation parts required, plus additional sound

enhancing components to give the best listening experience possible.

Using the 8”in your T5. Please note some T5 vehicle require the later larger T5.1

speaker adapter please check before installation which one you need.

Box Contents:

2 x OPTI6C or OPTI8C Woofers

2 x Tweeters

2 x VW Speaker Adapter brackets

2 x VW Tweeter Adaptors Brackets

2 x VW Wiring Adapter Cables

2x VW Tweeter Connectors

2 x VIBE Wave diffuser

*6.5” version Only

2 x Anti VIBE sound deadening

2 x Silicone Speaker Baffles*

*6.5” version Only

1 Pair Tweeter fittings

4 x T-Crimp Connectors

4 x Bullet Connectors

Specifications:

OPTI6C

Configuration –2-way

Speaker Size –6.5” (165mm)

Peak/RMS Power –270W/90W

Sensitivity –94dB

Frequency Response –54Hz –20kHz

Impedance –4Ω

Mounting Depth –2.4” (61mm)

OPTI8C

Configuration –2-way

Speaker Size –8” (200mm)

Peak/RMS Power –270W/90W

Sensitivity –94dB

Frequency Response –54Hz –25kHz

Impedance –4Ω

Tools Required:

- T25 Torx Screwdriver

- Trim Removal Tools (VIBE CLTRT-V7)

- T15 Socket & Ratchet

- Drill

- 5mm Drill Bit

- Pliers

- Wire Strippers

- Wire Crimpers

Removing the Door Card

1. To access the door speaker, first

carefully remove the door card. This is

secured with 6 x T25 Torx screws and

plastic panel clips. Ensure all screws and

clips are correctly removed and retained

for re-installation

2. Using a trim removal tool, remove the

plastic trim from the centre of the door

handle then remove the two T25 Torx

screws located behind. (We recommend

using the VIBE CLTRT-V7 trim removal

tools available from any VIBE authorised

dealer)

3. With the Torx screws removed, remove

the handle completely from the door

card.

4. Remove the single T25 Torx screw

located in the centre of the door card

5. Remove the three T25 Torx screws

located along the bottom edge of the

door card. Once removed, use a trim

removal tool to carefully release the

plastic clips securing the door card to

the door

6. With the door card fully released from

the door, unplug the window/door

switches, and release the door opening

cable. This is released by unclipping the

front edge and sliding it back out of its

locating channel. Once released,

unhook the metal cable

7. Once the door card is removed fully,

store safely to avoid damage.

Removing the Door card continued…

15.The factory speaker is secured to the

door using rivets. To remove the

speaker, drill out the rivets using a 5mm

drill bit. Take care not to damage the

vehicle and ensure protective eyewear

is worn. Once all rivets are removed,

unplug the speaker, and remove.

Note: Ensure the window is in the up

position when drilling the rivets.

16.Ensure the door panel is clean and free

from grease and dirt. Apply the self-

adhesive sound deadening to the door

panel directly behind the speaker as

shown. For maximum coverage cut the

sound deadening in half and place

above and below the door

strengthening bar

11.Affix the self-adhesive wave diffuser

directly behind the speaker. Ensure

its firmly secured as not to obstruct

the window when open.

10.Fix the speaker bracket to the door

panel by lining up the securing holes

and using nuts & bolts or

screw/rivets (not provided) to secure

the mounting bracket to the door

Replacing the Door Speakers

12.Connect the speaker wiring adaptor

and make a small hole in the rubber

grommet. Pass the speaker wires

through the grommet into the door

cavity. Ensure the wiring is kept tight

against to door skin as to not

obstruct the window when lowered

down

13.Insert the silicon baffle into the

speaker adaptor and line up the

securing holes. (6.5” version only)

14.Connect the speaker spade terminals

to the woofer ensuring the polarity is

correct (Red Positive +, Black

Negative -) Line up the holes and

silicone baffle and use the screws

provided to secure to the speaker

adaptor

Test the speaker and re-install the

door card. Re-installation is a

reversal of the removal process.

NOTE Please check the window does

not catch the Speaker on the 8” kit

when full down. If it does please add

a 2 mm spacer or foam gasket to the

back of the speaker. Extra Sound

deadening included which can be

fitted under the adapter and

speaker if need (8” version only)

Replacing the Door Speaker continued…

15.To remove the factory tweeter (if fitted)

first use a trim removal tool to remove

the dash cover. Lift the front edge first

and remove completely

16.Remove the tweeter (if fitted) by

removing the two T15 Torx screws

securing the tweeter mount to the dash

and unplugging the tweeter connector.

Safely retain the mounting screws for

reinstallation

17.Before fitting the new tweeters, please

make sure the crossover or capacitor is

used to protect the tweeter. (See

Section 21 for details.)

Secure the OPTI1C tweeter to the new

tweeter mount using the metal locking

ring provided.

18.For vehicles that are not fitted with

factory tweeters in the dash, the OPTI1C

tweeter wires will need to be routed to

behind the stereo. Connect the T Crimp

connecters as shown to the Tweeter

wires and clamp closed using pliers or

similar.

Please make sure the included

crossover is used. This can vary from

the kit order from inline to separate

yellow cap. This should be used on the

positive cable

Replacing the Tweeter T5 kit Dash Board Placement (T6 Fitting See 15B)

Vehicles WITHOUT factory fitted Tweeters

19.Connect the T-Crimp connectors to the

stereo front speaker output wires. Take

special care to ensure the polarity is

correct so power correctly flows

through the tweeter crossover. If unsure

refer to your stereo user guide or wiring

diagram. (Tweeter wiring, Black/White –

Positive +, Black –Negative -)

Note: Failure to complete this step

correctly may result in damage to the

tweeter

20. Add the bullet connectors provided to

the tweeter connector provided taking

note of the polarity. Red connects to the

tweeter wire (black/white) and black

connect to the tweeter wire (black)

21. Cut back the tweeter wiring ensuring

the crossover/capacitor remains in-line

with the positive wire (Black/White).

Add the blue bullet connectors provided

and connect to the tweeter connector.

Ensure the Polarity is correct and

connected as below

Tweeter Tweeter Connector

Black/White to Red

Black to Black

Note: Failure to complete this step

correctly may result in damage to the

tweeter

22. Reconnect the tweeter in the vehicle

and secure the tweeter mount using the

T15 screw previously removed. Test for

correct operation and refit the dash

cover

Vehicles WITH factory fitted Tweeters

15B. To gain access the tweeter on the T6

the A pillar needs removing.

A trim tool is recommended to remove

these to avoid breaking anything.

16B. Once removed the Tweeter is now

able to be removed. These are plastic

welded into place from factory and can

easily be removed with the use of heat and

a small amount of pressure.

Please refit in reverse. A glue gun may be

needed at this point

17B. The tweeters are to be fitted into the

original place and plug into the original

position.

These can be soldered and wrapped or use the

supplied Bullet connectors.

See point 20 and 21 for full details.

Note: Failure to complete this step

correctly may result in damage to the

tweeter which is not covered by

warranty.

Replacing the Tweeter T6 A Pillar

T6 with factory fitted Tweeters

Tel: 0121 311 9090 Email: info@midbass.co.uk

Warranty

All VIBE products carry a full 12-month warranty, valid from the date of the original

receipt and proof of purchase (UK only). The original receipt and packaging should

be retained for the full 12-month period. If the product develops a problem at any

stage during the warranty period, it should be returned to the point of purchase,

complete and in its original packaging.

A full description of VIBE’s warranty information can be found on our website.

What is not covered

- Damage to a product due to improper installation

- Subsequent damage to other components

- Damage caused by exposure to moisture, excessive heat, chemical cleaners

and / or UV radiation

- Damage through negligence, misuse, accident, or abuse. Repeat returns for

the same fault may be considered abuse

- Any cost or expense related to the removal and / or re-installation of the

product

- Damage caused by amplifier clipping or distortion

- Items repaired or modified by any unauthorised repair facility

- Return shipping on non-defective items

- Products returned without a return’s authorisation number

- Damage to product by sealant use.

International Warranty

Contact your international VIBE dealer or distributor concerning specific procedure

for your country’s warranty policies. www.vibeaudio.co.uk

Questo manuale è adatto per i seguenti modelli

Altri manuali Vibe Altoparlanti per auto

Vibe

Vibe Slick 3C-V2 Manuale utente

Vibe

Vibe SLICK SQ Series Manuale utente

Vibe

Vibe blackDeath Series Manuale utente

Vibe

Vibe SLICK PRO 37T Manuale utente

Vibe

Vibe 69 Coaxial PULSE69-V4 Manuale utente

Vibe

Vibe BLACKAIR6C-V0 Manuale utente

Vibe

Vibe SEK10 Manuale utente

Vibe

Vibe OPTISOUNDMERC4-V2 Manuale utente

Vibe

Vibe OPTISOUNDBMW8-V4 Manuale utente

Vibe

Vibe BlackDeath PRO-8M Manuale utente

Vibe

Vibe BlackAir 5 Manuale utente

Vibe

Vibe BLACKAIR PRO 4.5T Manuale utente

Vibe

Vibe BLACKDEATH PRO 3T Manuale utente

Vibe

Vibe SA-k Series Manuale utente

Vibe

Vibe qb69 Manuale utente

Vibe

Vibe BlackAir 5 Manuale utente

Vibe

Vibe PULSE6C-V4 Manuale utente

Manuali Altoparlanti per auto popolari di altre marche

Blaupunkt

Blaupunkt GTt 300 Scheda tecnica

Boston Acoustics

Boston Acoustics SX55 Manuale utente

Kenwood

Kenwood KFC-W212 Manuale utente

VR3

VR3 Elite VRS653 Manuale utente

Premier

Premier TS-W3001D4 Manuale utente

Infinity

Infinity 6530cx Manuale utente

Focal

Focal K2 Power 165 KRX3 Manuale utente

Precision Power

Precision Power PPI4.2 Manuale utente

Mopar

Mopar 2011-UP Manuale utente

Jensen

Jensen XS Series Manuale utente

Blaupunkt

Blaupunkt GTx Series Manuale utente

AudioBahn

AudioBahn AT60 Manuale utente

Focal

Focal BombA 27 V1 Manuale utente

Blueant

Blueant S1 Manuale utente

Naxa

Naxa NCS-768 Manuale utente

Focal

Focal Polyglass 130 VRS Manuale utente

Boston Mobile Audio

Boston Mobile Audio SR80 Manuale utente

Blaupunkt

Blaupunkt GTx 352 DE Manuale utente