Vicon V920B Series Manuale utente
www.vicon-security.com
XX271-20-00
V920B Series
Bullet Cameras
Vicon Industries Inc. does not warrant that the functions contained in this equipment will meet your requirements or that the
operation will be entirely error free or perform precisely as described in the documentation. This system has not been designed
to be used in life-critical situations and must not be used for this purpose.
Vicon Industries Inc.
Tel: 631-952-2288 Fax: 631-951-2288 Toll Free: 800-645-9116
24-Hour Technical Support: 800-34-VICON (800-348-4266) UK: 44/(0) 1489-566300
Document Number: 8009-8271-20-00
Product specications subject to change without notice.
Issued: 1114
Copyright © 2014 Vicon Industries Inc. All rights reserved.
Quick Guide
V920B Series Quick Installation Guide
V920B Series Quick Installation Guide
1. Description
The information in this manual provides quick installation and setup procedures for the Roughneck®
V920B Series of Bullet Cameras. These units should only be installed by a qualified technician using
approved materials in conformance with federal, state, and local codes. Read these instructions
thoroughly before beginning an installation. Always refer to Vicon’s website to assure you have the
most up-to-date manual, www.vicon-security.com.
The V920B Series of HD IP cameras is designed for demanding security installations. It offers a
number of fixed network camera versions that deliver crisp clear images to fit any installation need.
The V920B cameras are fully compatible with all ViconNet® systems; its ONVIF certification provides
an open-platform for integration into other video management systems.
The housing is designed for easy installation. PoE eliminates the need for power cables, providing a
cost-effective method of installation. The V920B features an auto iris lens that adapts to changing
outdoor lighting; the true day/night camera includes a removable IR cut filter. 32 IR LED illuminators
provide lighting up to 82 ft (25 m). The camera is IP67 rated with that withstands rain.
• Installation Steps
Follow these steps to install the network camera on your local network (LAN):
1. Check the package contents against the list that follows.
2. Connect the network camera.
3. Set an IP address.
4. Set the password.
• Package Component
The system comes with the following components:
Camera unit Installation CD Installation Quick Guide T emplate Sheet Accessory Kit
Optional OSD Controller
Check your package to make sure that you received the complete system, including all components
shown above.
Note: Adapter for12 VDC is not supplied; the optional V920D-OSD OSD Controller can be purchased
separately.
3
V920B Series Quick Installation Guide
2. Installation
For the network camera to operate, it is necessary to connect a network cable for data transmission
and power connection from customer-supplied power supply (if not using PoE).
2.1 Camera Installation
Camera Dimensions
See the diagrams below for the exact dimensions of the network camera.
Unit Dimensions: mm
Parts and Description
4
V920B Series Quick Installation Guide
Sunshield Installation
The unit is shipped without the sunshi eld installed. Use the bolt supplied to secur e the sunshiel d
to the body of the camera.
Base Installation
There are two ways of installing the camera.
3. Route cable through the wall to
mounting base. 1. Route cable through the cable
knockout tab in mounting base.
1) Installation1 (Cable through the wall with the mount base)
PTS1, M5x20 Mounting Screws (3x)
Mounting Base
Plastic Anchors (3x)
Templa t e S h ee t
Wall Loosen the mount screw (M6x16 mm)
A. Drill the mounting hole locations, using the template sheet (or the bottom of the mount
base) as a guide.
B. Insert the supplied plastic anchors into the holes.
C. Connect power cable and network line.
D. Align the screw holes of the mount base with the plastic anchors.
E. Use the mounting screws (M5x20) provided to secure the camera.
F. To adjust the camera position, loosen the mount screw (M6x16) to move the camera.
Retighten the screw when adjustment is complete.
5
V920B Series Quick Installation Guide
2) Installation 2 (Using the cable knockout tab in mount base)
PTS1, M5x20 Mounting Screws (3x)
Mounting Base
Plastic Anchors (3x)
Templa t e S h ee t
Wall Remove the cable knockout tab for
cable entry
A. Drill the mounting hole locations, using the template sheet (or the bottom of the mount
base) as a guide.
B. Insert the plastic anchors into the hole which has just drilled.
C. Connect connection cable and network lines.
D. Fit the screw holes of the mount base into the plastic anchors.
E. Remove the cable knockout tab for the cable entry.
F. Screw up the mount screws (M5x20).
G. To adjust the camera position, loosen the mount screw (M6x16) to move the camera.
Retighten the screw when adjustment is complete.
6
V920B Series Quick Installation Guide
2.2 Connections
Cable Connections
NO Wire Color Description
1 Red: 12 VDC
White: GND
Main Power; 2 pin terminal, 12 VDC 2A (24W) with heater,
or 12 VDC 320mA (3.8W) without heater
2 Black Ethernet; RJ-45 port compatible with 10/100Mbps having PoE
functionality. Modular jack.
Note: Heater requires 12 VDC.
If using PoE, the heater will not operate.
• Connecting to the RJ-45
Connect a standard RJ-45 cable to the network port of the network camera. Generally a
cross-over cable is used for direct connection to PC, while a direct cable is used for connection
to a hub.
A router featuring PoE (Power over Ethernet) can be used to supply power to the camera.
Micro SD memory slot
Remove the rear cap on the camera to insert the SD memory card.
• Connecting
the Power
Connect the power of 12 VDC for the network camera. Connect the positive (+) pole to the ‘+’
position (red) and the negative (-) pole to the ‘-’ position (white) for the DC power.
Be careful not to reverse the polarity when connecting the power cable.
A router featuring PoE (Power over Ethernet) can be used to supply power to the camera.
The heater only operates when using the power source of 12 VDC.
If using PoE, the heater will not operate.
If PoE and 12 VDC are both applied, the camera will be supplied with power from PoE.
7
V920B Series Quick Installation Guide
• Connecting Service Monitor Port
Service monitor port is used for easy OSD setup. To make changes from the OSD menu, use the
optional OSD controller.
▶ID & IP assignment
To make changes in the OSD menu, the optional OSD controller (V920D-OSD) can be used to set
Camera Title and IP Address.
1. Connect the OSD Controller to the Service Monitor port of the network camera.
2. Connect Service Monitor and the Video Output port of the OSD Controller.
3. Press the SET button on the controller to access the Main Menu.
4. Change camera ID and IP address as needed. Additionally, the Name (or title) of the camera
can be changed. Use the ↑↓←→ buttons on the controller to change the parameters.
5. Select SAVE or CANCEL to exit the Main Menu.
The Video Output can also be used for easy zoom and focus control when adjusting the lens.
Video Output is restricted to 704x480 (576) resolution.
▶Zoom & Focus Control (Models with motorized lens only)
The camera enters Zoom and Focus control mode when the OSD Controller is connected to the
Service Monitor port.
-. Zoom Control:↑ (Zoom In), ↓(Zoom Out)
-. Focus Control:←(Focus Near), →(Focus Far)
-. Fine Focus: Press and hold the SET button for at least 2 seconds. The camera readjusts
focus automatically.
Note:
The optional V920D-OSD OSD Controller can be purchased separately.
8
V920B Series Quick Installation Guide
2.3 Network Connection and IP assignment
The network camera is designed for use on an Ethernet network and requires an IP address for
access. Most networks today have a DHCP server that automatically assigns IP addresses to
connected devices. By the factory default, your camera is set to obtain the IP address automatically
via DHCP server. If your network does not have a DHCP server the network camera will use
192.168.1.100 as the default IP address.
If DHCP is enabled and the product cannot be accessed, run the “Smart Manager” utility on the CD to
search and allocate an IP address to your products, or reset the product to the factory default settings
and then perform the installation again.
1. Connect the network camera to the network and power up.
2. Start SmartManager utility (Start>All Programs>SmartManager>SmartManager); the main
window displays. After a short while any network devices connected to the network will be
displayed in the list.
3. Select the camera on the list and click right button of the mouse. The pop-up menu below
displays.
4. Select Assign IP. The Assign IP window displays. Enter the required IP address.
Note: For more information, refer to the Smart Manager
User’s Manual.
9
V920B Series Quick Installation Guide
3. Operation
The network camera can be used with Windows® operating system and browsers. The recommended
browsers are Internet Explorer®, Safari®, Firefox®, Opera® and Google® Chrome® with Windows.
Note: To view streaming video in Microsoft® Internet Explorer, set your browser to allow ActiveX
controls.
Note: Some screens may appear different (i.e., color scheme) depending on the firmware version, but
the functionality is the same or similar.
3.1 Access from a Browser
1. Start a browser (i.e., Internet Explorer).
2. Enter the IP address or host name of the network camera in the Location/Address field of the
browser.
3. A starting page displays. Click Live View, Playback or Setup to select corresponding web page.
4. Click Live View for the network camera’s Live View page to appear in the browser.
10
Altri manuali per V920B Series
1
Indice
Altri manuali Vicon Telecamera di sicurezza
Vicon
Vicon Surveyor 282-20-02 Series Manuale utente
Vicon
Vicon V2008-W0950-LPR Manuale utente
Vicon
Vicon Roughneck AI V2008B-W310LPR Manuale utente
Vicon
Vicon Roughneck V894CSHR-VF-C Manuale utente
Vicon
Vicon 360 Multi-Sensor Camera Series Manuale utente
Vicon
Vicon V672-PTZ Manuale utente
Vicon
Vicon Cruiser SN663V-B-EX Istruzioni operative
Vicon
Vicon V9317H Series Manuale utente
Vicon
Vicon V980B Series Manuale utente
Vicon
Vicon XX247-10-01 Manuale utente
Vicon
Vicon V840D Series Manuale utente
Vicon
Vicon V661D-312IR Istruzioni operative
Vicon
Vicon Surveyor MKII Series XX282-20-00 Manuale utente
Vicon
Vicon VC466-DSP Manuale utente
Vicon
Vicon V923-N Manuale utente
Vicon
Vicon ROUGHNECK V-CELL-HD-B Manuale utente
Vicon
Vicon ROUGHNECK V910 Manuale utente
Vicon
Vicon VC5050-DSP Manuale utente
Vicon
Vicon XX264-20-00 Manuale utente
Vicon
Vicon Roughneck V920D Series Manuale
