Viconics VT8000 Series Manuale utente

Version 4

VT8000 Room Controllers

VT8000 ZigBee Pro Module Installation Guide

VCM8000V5045P

028-0425-04_II-VT8000-VCM8000_A4_EN www.viconics.com February 2020

Figure 3

Figure 2

Figure 1

2VT8000 [ZigBee Pro Module Installation Guide ]

Installation

This guide shows you how to install the ZigBee Pro

wireless module with a VT8000 Room Controller.

1. Remove the security screw from the bottom of

the Room Controller cover.

2. Open the unit by pulling on the bottom of the

Room Controller (Figure 1).

3. Carefully turn the Room Controller over to access

the motherboard.

4. Locate the gap in the upper-right corner of the

Room Controller’s motherboard, as well as the

holes indicating where to insert the ZigBee Pro

module into the motherboard (Figure 2).

5. Align the connector pins of the ZigBee Pro

module with the holes on the motherboard.

NOTE: Ensure the pins are aligned correctly to

avoid damaging the ZigBee Pro module.

6. Gently press the ZigBee Pro module into the

Room Controller’s motherboard until it ﬁts snugly

into place.

NOTE: Do not press too hard to avoid damaging

the ZigBee Pro module.

7. Gently align the cover with the top of the base,

and snap it into place from the bottom (Figure 3).

8. Install the security screw.

028-0425-04_II-VT8000-VCM8000_A4_EN www.viconics.com February 2020

3VT8000 [ZigBee Pro Module Installation Guide ]

Quick setup

This short procedure is intended to let you pair a ZigBee sensor with your Room Controller.

It assumes that all the back-end conﬁguration of the stand alone Room Controller acting as

coordinator or the Multi-Purpose Manager (MPM) coordinator for the ZigBee network has

already been done, and it assumes that the user is familiar with the Permit Join function

and the Wireless Ecosystem screen functions.

Procedure

1. Set Permit Join on your Room Controller (or networked MPM coordinator if used) to On.

2. Go to the ﬁrst unused Zone screen in the Wireless Ecosystem section of the Room

Controller’s interface.

3. Insert the battery or remove the pull tab (for contact sensors) to activate the ZigBee

sensor.

4. Verify that the sensor has joined the network, and that on the Zone screen the Paired

ﬁeld status reads Yes.

5. Set the Set function to parameter to the correct setting.

6. Set Permit Join on your Room Controller (or networked MPM coordinator if used) to Off.

7. Conditional to use of door or window contact sensors

a. Go to the ﬁrst screen in the Conﬁguration section of the interface.

b. For window sensor, set UI 16 to Window.

c. For door sensor, set UI 17 to Door Dry.

8. Physically install the sensor.

Troubleshooting

If the short procedure described here is insufﬁcient or an MPM or Room Controller needs

to be conﬁgured, please refer to the VT8000 Room Controllers ZigBee Sensors Integration

Guide available on www.viconics.com.

California Proposition 65

WARNING

CALIFORNIA PROPOSITION 65

This product can expose you to chemicals including Lead, which are known to the State of California to cause cancer and

birth defects or other reproductive harm. For more information, go to

www.P65Warnings.ca.gov.

Failure to follow these instructions can result in birth defects or other reproductive harm.

Altri manuali per VT8000 Series

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Viconics Controllori

Viconics

Viconics VT7225 series Manuale utente

Viconics

Viconics VT7225 series Manuale utente

Viconics

Viconics VC3000 Series Manuale utente

Viconics

Viconics VT8600 Series Manuale utente

Viconics

Viconics VT7600 Series Manuale utente

Viconics

Viconics ZigBee Pro VT8000 Series Manuale utente

Viconics

Viconics VT8000 Series Scheda tecnica

Viconics

Viconics R851V Series Manuale utente

Viconics

Viconics VTR7300 Series Manuale utente

Viconics

Viconics R820 REV2 Series Manuale utente

Viconics

Viconics VT76 Series Manuale per l'uso e la cura

Viconics

Viconics VT8000 Series Manuale utente

Viconics

Viconics COV-PIR-FCU-C-5000 Manuale utente

Viconics

Viconics VZ7260 5 00B Series Guida utente

Viconics

Viconics VTR7300 Series Manuale utente

Viconics

Viconics VTR7300 Series Manuale utente

Viconics

Viconics VT7600F Series Manuale utente

Viconics

Viconics VZ7656F1000B Manuale utente

Viconics

Viconics R850 Series Manuale utente

Viconics

Viconics VT8000 Series Manuale utente

Viconics

Viconics VTR8300 Series Guida utente

Viconics

Viconics VT7200 Series Manuale utente

Viconics

Viconics VZ8250 Manuale utente

Viconics

Viconics VT7600E Series Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente