Victor SMART-KILL M1 Manuale utente

SMART-KILL™

USER GUIDE

Electronic Traps

View additional languages at:

www.victorpest.com/smart-kill-instructions

Victor®Smart-Kill™ Electronic Mouse Trap

Model: M1

Victor®Smart-Kill™ Electronic Rat Trap

Model: M2

Manufactured for:

Woodstream Corporation

69 N. Locust Street, Lititz, PA 17543

800-800-1819

Woodstream Canada Corporation

25 Bramtree Ct. Unit 1

Brampton, ON L6S 6G2

800-800-1819

FCC COMPLIANCE:

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE

FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE,

AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING

INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

WARNING: Changes or modications to this device not expressly approved by Woodstream

Corporation could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/TV technician for help.

RF Exposure:

This equipment complies with FCC and IC radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated with a minimum

distance of 20cm between the radiator and your body.

Industry Canada:

This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to

the following two conditions: (1) This device may not cause interference; and (2) This device

must accept any interference, including interference that may cause undesired operation of

the device.

WARNING: Electric Shock and Spark Hazards

Ignition: Use indoors ONLY on dry, clean surfaces. Do not use near unvented ammable

vapors, liquids, or combustible solids. Do not use in barns, stables, or similar wet or dusty

locations.

High Voltage: Keep out of reach of children and pets. Use only dry hands or rubber gloves to

handle. Power OFF and separate units before baiting. Do not touch metal plates when device

is powered on.

Electromagnetic Waves: Keep pacemakers and life support devices at least one foot

away. Consult your heart doctor if you receive a shock. Failure to read and heed all warnings

and directions may cause electric shock, re, or serious injury. Read and follow all label

instructions.

EU Declaration of Conformity: Hereby, Woodstream Corporation declares that the radio

equipment type Victor Smart Kill M1 and Victor Smart Kill M2 is in compliance with Directive

2014/53/EU. The full text of the EU declaration of conformity is available at the following

internet address: www.victorpest.com/eu_doc

This device operates in the 2.4 GHz ISM band. Maximum transmitted power: 19.85 dBm

Please read and follow all warnings and safety instructions!

This appliance is not to be used by persons with reduced physical, sensory or mental

capabilities or lack of experience and knowledge unless they have been given supervision

or instruction concerning use of the appliance in a safe way and understand the hazards

involved. Children shall not play with the appliance. Cleaning and user maintenance shall not

be performed by children

This symbol on the product means that used electrical and electronic products should

not be mixed with general household waste. For proper treatment, recovery and

recycling, please take this product(s) to designated collection points where it will be

accepted free of charge. Please contact your local authority for further details of your

nearest designated collection point. Penalties may be applicable for incorrect disposal

of this waste, in accordance with your national legislation.

MOUSE TRAP BATTERIES: 4 AA batteries are needed to operate this trap. Insert and

remove batteries as indicated in the instructions. Non-rechargeable batteries are not to

be recharged. Rechargeable batteries are to be removed from the appliance before being

charged. Different types of batteries or new and used are not to be mixed. Batteries are to

be inserted with the correct polarity as indicated in the battery compartment. Exhausted

batteries are to be removed from the trap and safely disposed of. If the trap is to be stored

unused for a long period, the batteries should be removed. The supply terminals are not to be

short-circuited.

RAT TRAP BATTERIES: 4 C batteries are needed to operate this trap. Insert and remove

batteries as indicated in the instructions. Non-rechargeable batteries are not to be recharged.

Rechargeable batteries are to be removed from the appliance before being charged. Different

types of batteries or new and used are not to be mixed. Batteries are to be inserted with

the correct polarity as indicated in the battery compartment. Exhausted batteries are to be

removed from the trap and safely disposed of. If the trap is to be stored unused for a long

period, the batteries should be removed. The supply terminals are not to be short-circuited.

You Will Need:

•A smart phone, tablet or similar connected mobile device.

•Broadband internet connection. Do NOT use a phone/tablet hot spot.

•A strong Wi-Fi signal where trap will be placed.

•Password for your home network.

•A Victor®Smart-Kill™ trap.

•A set of brand new batteries (4 “AA” for the mouse trap, 4 “C” for the rat trap).

Important Notes

•Once a rodent is caught, a notication is sent to your connected device if it is connected to

the Victor®Pest App.

•A notication is sent to your mobile device when the battery life of the trap is low. Replace

batteries when you receive this notication.

•You can share your experience through social media within the App.

•The trap will still operate without being connected to Wi-Fi. However, you will not receive

notications upon catching a rodent and will need to regularly check the trap.

•Visit: www.victorpest.com/electronics for customer support.

Trouble Shooting:

STOP! If you have questions or problems with your purchase do not return

it to the retail store. Please contact us directly for immediate assistance at

1-855-5-VICTOR.

Modern routers usually have a selection for the operating frequency.It is most typically

2.4GHz (the default setting) or 5GHz.

2 3

Frequently Asked Questions

•Where should I place my trap?

Traps can be placed anywhere indoors. Place trap against a wall where rodent activity is

frequently seen.

•Where is my trap/QR code?

The QR code is located on the bottom of the mouse trap and the back of the rat trap.

•What kind of bait should I use?

The best baits are high in fat and protein, such as peanut butter or hazelnut spread.

•How much bait do I need?

The trap has a bait cup that shows you exactly how much bait to use. Do not overll the

bait cup. Do not place bait on the metal plates. Doing so may interfere with the electrical

functionality and your trap may not work unless you completely clean the bait off.

Network Speed:

The Gigahertz (GHz) range that a wireless device is using does not necessarily determine the

maximum speed of the Wi-Fi.A Wireless-A device that runs on the 5 GHz band can also

support a maximum data rate of up to 54 Mbps, which is exactly the same data rate that a

Wireless-G device running on the 2.4 GHz band supports.

Range:

The 5 GHz band has a shorter range compared to a 2.4 GHz band. Because in radio

frequencies, the higher the frequency the shorter its range. In other words, if you are using

a lower frequency like the 2.4 GHz, the distance it will cover will be greater than the 5 GHz

band.

Band 2.4 GHz 5 GHz

Channel Three non-overlapping

channels

23 non-overlapping

channels

Standard Wireless-B, G, and N Wireless-A, N, and AC

Network Range Wider Range Shorter Range

You may need to check your Wi-Fi signal strength. Do this by making sure your mobile device

is connected to your Wi-Fi network. Hold your mobile device in the place where your Victor®

Smart-Kill™ trap will be stationed and check the Wi-Fi signal strength.

If you see:

Wi-Fi signal is strong. You’re all set!

Wi-Fi signal is weak. Your Victor®Smart-Kill™ trap will likely connect to your

Wi-Fi network, but connection may be intermittent.

No Wi-Fi signal:

Try one of the following:

• Move your router closer to your Victor®Smart-Kill™ trap.

•Buy a Wi-Fi range extender.

Indications that the trap did not successfully connect to Wi-Fi during setup:

•A network/server error has occurred if the blue Wi-Fi light and the red Victor®“V” light stay

on for 5 seconds. Power the trap off and start over.

•A password error has occurred if the blue Wi-Fi light and the red Victor®“V” light blink for 5

seconds. Re-enter password. Note that passwords are case sensitive.

1. Press Power Button

Press the power button to turn the trap on. The Victor®“V” will blink green 3 times.

2. Press and Hold Wi-Fi Button for 5 Seconds

The Wi-Fi button will blink blue 10 times while the trap is connecting.

3. Scan Trap Code

Center the trap’s code in the window on the screen. The trap code is the QR code located

on the bottom of the mouse trap and the back of the rat trap. See FAQ page for images of

QR code locations.

1 2

•How do I dispose of a caught mouse?

Press the power button to turn the unit “OFF”. Open the kill chamber door and properly

discard rodent. Clean and bait trap after each use for most effective results. Press the

power button to turn the unit back on. The trap will automatically reconnect to Wi-Fi.

Opening and closing the kill chamber door will re-arm the mouse trap if it has not been

powered “OFF”.

•How do I dispose of a caught rat?

Press the power button to turn the unit “OFF.” Properly discard rodent. Clean and bait trap

after each use for most effective results. Press power button to turn the unit back on. The

trap will automatically reconnect to Wi-Fi.

Getting Started: Android Devices

1. Download the free Victor®Pest App from the Apple App Store®or Android Google Play™

store. Check that the unit is turned “OFF” by making sure the power button is not pressed

down. Insert batteries into the battery compartment and launch the Victor®Pest App.

2. Connect your trap by following the instructions on screen. Step by step instructions are

also in this guide.

3. Once the power button and Wi-Fi button have been pressed during the initial setup, users

will have 5 minutes to successfully nish. Once 5 minutes have passed, the user should

power the trap off and start over if setup was not successful.

Android Devices

Important Note: Some screens, instructions and settings may differ slightly

depending on what device you are using.

4. Connect Mobile Device to Trap

Go to Wi-Fi settings on your device by pressing the red “GO TO SETTINGS” button.

Select the trap, which is VICTOR followed by 15 alphanumeric digits.(Ex: VICTOR-

WM170818BE00004). Press “Connect”, then press the back button.

4 4

3. Scan Trap Code (Continued)

If you have trouble successfully scanning the code, try changing the distancte between

the trap and mobile device. Alternatively you can enter the 15 digit alphanumeric code

manually by pressing the “ENTER CODE MANUALLY” text found on the bottom of the

screen. Enter the serial number found next to the QR code on your trap.

5 5

6. Connected

A notication appears when the trap successfully connects. Press the red “Next” button

and continue to step number 8

7. Unable to Connect

If your trap did NOT successfully connect, go to the Settings menu of your mobile device,

then select the Wi-Fi option.Select more options (often can be found by pressing the

options button in the top right corner) then select “Saved Networks.”

6 6

5. Connect Trap to Wi-Fi

Select the Wi-Fi network to connect the trap to.

Enter the network password for the Wi-Fi network, then press the red “Connect” button. It

may take up to 1 minute to connect.

7 7

7. Unable to Connect (Continued)

Find the trap name

(Ex: VICTOR-WM170818BE00004) and select it.

Select “FORGET.”

Power trap off, then repeat steps 1 through 7. If the trap still does not connect, visit the

Trouble Shooting section or call 1-855-5-VICTOR for immediate assistance.

8. Name Your Trap

After successful connection, name the trap and press the red “Next” button.

9. Bait and Place Trap

Swipe through the three instruction screens on baiting and placing the trap, then press

the red “Done button. Visit the Frequently Asked Questions section for more information on

baiting and placing the trap.

8 9

1 2

10. Monitor Trap

Stay up to date on trap activity from anywhere via your mobile device.

Getting Started: iOS Devices

1. Download the free Victor®Pest App from the Apple App Store®or Android Google Play™

store. Check that the unit is turned “OFF” by making sure the power button is not pressed

down. Insert batteries into the battery compartment and launch the Victor®Pest App

2. Connect your trap by following the instructions on screen. Step by step instructions are

also in this guide.

3. Once the power button and Wi-Fi button have been pressed during the initial setup, users

will have 5 minutes to successfully nish. Once 5 minutes have passed, the user should

power the trap off and start over if setup was not successful.

iOS Devices

Important Note: Some screens, instructions and settings may differ slightly depending

on what device you are using.

1. Press Power Button

Press the power button to turn the trap on. The Victor®“V” will blink green 3 times.

2. Press and Hold Wi-Fi Button for 5 Seconds

The Wi-Fi button will blink blue 10 times while the trap is connecting.

3. Scan Trap Code

Center the trap’s code in the window on the screen.The trap code is the QR code located on

the bottom of the mouse trap and the back of the rat trap. See FAQ page for images of QR

code locations.

3. Scan Trap Code (Continued)

If you have trouble successfully scanning the code, try changing the distance between the

trap and mobile device. Alternatively you can enter the 15 digit alphanumeric code manually

by pressing the “ENTER CODE MANUALLY” text found on the bottom of the screen. Enter the

serial number found next to the QR code on your trap.

4. Connect Mobile Device to Trap

Go to Wi-Fi settings on your device by pressing the red “GO TO SETTINGS” button.

Select the trap, which is VICTOR followed by 15 alphanumeric digits. w(Ex: VICTOR-

WM170818BE00004). Press the back button on the device’s top menu bar to return to the

Victor®Pest App.

Questo manuale è adatto per i seguenti modelli

Indice

Lingue:

Altri manuali Victor Controllo dei parassiti

Victor

Victor M241 Manuale utente

Manuali Controllo dei parassiti popolari di altre marche

Woodstream

Woodstream Victor RZC001-4 Manuale utente

Gardigo

Gardigo 90160 Manuale utente

Bird-X

Bird-X Super Broadband PRO Manuale utente

Bird-X

Bird-X Super BirdXPeller Pro Manuale utente

Radarcan

Radarcan PORTABLE MOSQUITO REPELLER Manuale utente

DynaTrap

DynaTrap DT0500IN Manuale utente

BRC

BRC FLYinBOX 20 Manuale utente

ECOstyle

ECOstyle Cat & Dog free 200 m2 Manuale utente

Bell LABORATORIES

Bell LABORATORIES PULSE MOUSE IQ Manuale utente

Gimenez Ganga

Gimenez Ganga Saxun 27 Vertical Manuale utente

Silverline

Silverline gardenSystem Cat & Dog Free 200 Manuale utente

Segula

Segula 50520 Manuale utente

Isotronic

Isotronic Spacedog II Manuale utente

Radarcan

Radarcan radarhealth RH-105 Manuale utente

Heitronic

Heitronic 90111 Manuale utente

Beamshot

Beamshot BR100 Manuale utente

Kerbl

Kerbl UltraStop Rat&Mouse Manuale utente

Weitech

Weitech WK0025 Manuale utente