Victron energy CCGX Istruzioni operative
2020-11-11 18:40 1/5
Victron Energy - https://www.victronenergy.com/live/
Troubleshooting CCGX to VRM connectivity
This document outlines the procedure to troubleshoot connectivity between a Color Control GX and
the VRM Portal, https://vrm.victronenergy.com/.
Please also read the manual of the Color Control GX on how to setup an internet connection and the
logging to the VRM Portal: https://www.victronenergy.com/live/ccgx:start
Not using a Color Control GX but a Victron Global Remote or Victron Ethernet Remote? See this
document instead:
https://www.victronenergy.com/upload/documents/Manual-Troubleshooting-VGR-connectivity-EN.pdf.
Trouble shooting Remote Console on VRM? See last section in this document.
Step 1 - Verify that the Color Control has received an IP
address
In the menu Settings → Ethernet or Settings → Wi-Fi, State should be ‘Connected’ and there should be
an IP address that does not start with 169:
When using Ethernet and State shows 'Unplugged', verify that the Ethernet network cable is not
faulty: try another one. The two lights at the back of the CCGX, where the Ethernet RJ45 cable plugs
in, should be lit or blinking. Two dead lights indicate a connection problem.
When using Wi-Fi and the menu shows 'No Wi-Fi adapter connected' check the USB connection to the
Last
update:
2016-06-29
01:50
vrm_portal:troubleshooting_ccgx_vrm_connectivity https://www.victronenergy.com/live/vrm_portal:troubleshooting_ccgx_vrm_connectivity?rev=1467157821
https://www.victronenergy.com/live/ Printed on 2020-11-11 18:40
Wi-Fi dongle. Try to remove the dongle and insert it again.
When using Wi-Fi and the State shows 'Failure', it might be that the Wi-Fi password is incorrect. Press
'Forget network' and try to connect again with the correct password.
In case there is an IP address that starts with 169, check whether your network had a DHCP server
running. 99% of all networks have a DHCP server running and it is enabled by default on all well-
known ADSL, cable and 3G routers. If there is no DHCP server running, then the ip address should be
configured manually.
Step 2 - Check connectivity between CCGX and VRM Portal
Navigate to Settings → VRM online portal.
1) Check that 'Log To' is set to 'Internet'. If this is set to 'microSD or USB storage', then the CCGX will
not log directly to the VRM portal using an internet connection, but will log to inserted microSD or USB
storage. The database files on this storage should be uploaded manually on the VRM portal.
2) Check 'Last contact'. If this shows dashes or a time that is much larger than 'Log interval', make
sure that your network has access to the internet. Plugin a laptop and navigate to
https://vrm.victronenergy.com/ for example.
If 'Buffered items' is larger than 0, it means that the CCGX cannot connect to the VRM Portal. All data
is sent using the First in First out principle: the VRM Portal will only show the most up to date
information after all old data has been sent.
Data is sent to the VRM Portal using HTTP POST requests to
http://ccgxlogging.victronenergy.com/log/log.php. In case all above checks have been done, internet
connection is sure to work, and still 'Last contact' keeps showing dashes: try logging into the CCGX
with ssh. And do:
wget --quiet -O- http://ccgxlogging.victronenergy.com/log/log.php
The output should be a line containing the text 'vrm: OK'. If it does not, or wget hangs, check your
network. Apparently communication is blocked.
2020-11-11 18:40 3/5
Victron Energy - https://www.victronenergy.com/live/
Using HTTPS instead of HTTP
If your provider is blocking HTTP requests (e.g. the wget request above times out or fails), you can
change the CCGX to log to the VRM portal via HTTPS:
root@ccgx:~# dbus -y com.victronenergy.settings /Settings/Vrmlogger/Url
SetValue https://ccgxlogging.victronenergy.com/log/log.php
Verify that the setting has been changed:
root@ccgx:~# dbus -y com.victronenergy.settings /Settings/Vrmlogger/Url
GetValue
'https://ccgxlogging.victronenergy.com/log/log.php'
It is then recommended to reboot the CCGX to apply the changes. (Alternatively, you could manually
restart the vrmlogging services, but it's easier just to restart)
After you reboot, you should see the buffer size decrease:
# before rebooting
root@ccgx:~# dbus -y com.victronenergy.logger /Buffer/Count GetValue
375
# after rebooting
root@ccgx:~# dbus -y com.victronenergy.logger /Buffer/Count GetValue
362
Step 3 - Add the site to your VRM account
Adding a CCGX to your account is only possible after the CCGX has made its first initial contact to the
VRM Portal.
As long as 'Last Contact' shows 'Never', go back to step 1 and 2.
Once the internet communication is up, and 'Last contact' shows several seconds or minutes ago,
continue with ADD Site on the VRM Portal. See Getting started with VRM for further instructions.
General notes
On initial contact with the VRM site it may take a few minutes for data to appear, as a newly-
connected or re-connected CCGX’s presence requires that data to be filtered through our back-
end systems, before the information becomes visible on the VRM site.
If the data backlog size continues to increase after the chosen logging interval time is met, then
you have internet connectivity issues. You could try to increase the logging interval to a longer
time, in order to reduce necessary bandwidth. Bandwidth requirement is quite low, so this only
happens when using a cellular data connection, try moving the antenna or obtain a higher gain
antenna.
Last
update:
2016-06-29
01:50
vrm_portal:troubleshooting_ccgx_vrm_connectivity https://www.victronenergy.com/live/vrm_portal:troubleshooting_ccgx_vrm_connectivity?rev=1467157821
https://www.victronenergy.com/live/ Printed on 2020-11-11 18:40
Trouble shooting Remote Console on VRM
The Remote Console on VRM feature allows full remote control of a CCGX, over the internet:
After enabling the feature in the CCGX setting menu, and then restarting the CCGX, a green button
will show on the VRM website. Click it to open the Remote Console.
Steps to take when it does not work:
First make sure that basic communication with VRM works, see above steps.1.
After enabling the feature, make sure to restart the CCGX.2.
Make sure to update to CCGX v1.32 or higher: instead of only connecting on port 80, it also tries3.
22 and 443 which has proven to solve connection issues for several users.
After the restart, check the Remote Console on VRM status shows online or a port number. In4.
2020-11-11 18:40 5/5
Victron Energy - https://www.victronenergy.com/live/
case it says offline, or port number 0, the CCGX was unable to connect to the Remote Console
server. This is normally caused by a (company) firewall, blocking the connection. The solution is
then to configure an exception rules in the firewall.
Verify that your local web browser can access the websocket port (8080 on5.
vncrelay.victronenergy.com). If you click that link and get 'Error response, method not allowed',
it means the connection between your PC and the VNC relay is working. If you get a timeout or
another (browser) error, there may be a firewall blocking the connection.
Remote Console on VRM uses the same reverse SSH tunnel as is used for Remote Support: outbound
connection to supporthost.victronenergy.com on port 22, 80 or 443. It is not necessary to set up port
forwarding in routers to use Remote Console on VRM. It is however necessary for the firewall/router to
which the CCGX is connected, to allow outbound connections to supporthost.victronenergy.com on at
least one of these ports: 22, 80 or 443. Most routers will allow this by default.
Enabling Remote Console from the commandline
If you have a CCGX already installed, but Remote Support is not enabled, follow these steps to enable
it remotely:
SSH into CCGX (get root password by emailing [email protected])1.
dbus -y com.victronenergy.settings /Settings/System/RemoteSupport SetValue 12.
dbus -y com.victronenergy.settings /Settings/System/VncInternet SetValue 13.
dbus -y com.victronenergy.settings /Settings/System/VncLocal SetValue 14.
touch /data/conf/vncpassword.txt5.
Reboot CCGX via SSH (reboot)6.
Now you should be able to access Remote Console feature from VRM7.
If you want to set a password, go to Settings → Remote Console → Enable password check8.
DISQUS Comments
View the discussion thread.
From:
https://www.victronenergy.com/live/ - Victron Energy
Permanent link:
https://www.victronenergy.com/live/vrm_portal:troubleshooting_ccgx_vrm_connectivity?rev=1467157821
Last update: 2016-06-29 01:50
Altri manuali per CCGX
9
Indice
Altri manuali Victron energy Controllori
Victron energy
Victron energy BlueSolar MPPT 150/35 Manuale utente
Victron energy
Victron energy BlueSolar MPPT 150/85 Manuale utente
Victron energy
Victron energy BlueSolar PWM-Pro Series Manuale utente
Victron energy
Victron energy CCGX Istruzioni operative
Victron energy
Victron energy SmartShunt IP65 Manuale utente
Victron energy
Victron energy SHS 200 MPPT Manuale utente
Victron energy
Victron energy BlueSolar MPPT 150/35 Manuale utente
Victron energy
Victron energy BlueSolar MPPT 150/70-Tr Manuale utente
Victron energy
Victron energy BlueSolar MPPT 150/45-Tr Manuale utente
Victron energy
Victron energy CCGX Manuale utente
Victron energy
Victron energy SmartSolar MPPT 150/35 Manuale utente
Victron energy
Victron energy Lynx Smart BMS Manuale utente
Victron energy
Victron energy VE.Bus BMS Manuale utente
Victron energy
Victron energy EasySolar-II GX Manuale utente
Victron energy
Victron energy BlueSolar MPPT 150/60-Tr Manuale utente
Victron energy
Victron energy Isolated SmartSolar MPPT RS 450/100 Manuale utente
Victron energy
Victron energy CCGX Manuale utente
Victron energy
Victron energy BlueSolar MPPT 150/70 Manuale utente
Victron energy
Victron energy BlueSolar MPPT 75/15 Manuale utente
Victron energy
Victron energy BlueSolar MPPT 150/60 Manuale utente
