Videotec UCCMA Manuale utente
Instruction manual - English - EN
1MNVKUCCMA_1635_EN
ENGLISH
UCCMA
Ceiling bracket for upside down mounting and working of ULISSE COMPACT
1 About this manual
Read all the documentation supplied carefully before
installing and using this unit. Keep the manual in a
convenient place for future reference.
1.1 Typographical conventions
DANGER!
High level hazard.
Risk of electric shock. Disconnect the
power supply before proceeding with any
operation, unless indicated otherwise.
CAUTION!
Medium level hazard.
This operation is very important for the
system to function properly. Please read
the procedure described very carefully and
carry it out as instructed.
INFO
Description of system specications.
We recommend reading this part carefully
in order to understand the subsequent
stages.
2 Notes on copyright and
information on trademarks
The quoted names of products or companies are
trademarks or registered trademarks.
3 Safety rules
CAUTION! Device installation and
maintaining must be performed by
specialist technical sta only.
• The manufacturer declines all responsibility
for any damage caused by an improper use
of the appliances mentioned in this manual.
Furthermore, the manufacturer reserves the right
to modify its contents without any prior notice.
The documentation contained in this manual has
been collected with great care. The manufacturer,
however, cannot take any liability for its use. The
same thing can be said for any person or company
involved in the creation and production of this
manual.
• Before starting any operation, make sure the
power supply is disconnected.
• Be careful not to use cables that seem worn or old.
• Never, under any circumstances, make any
changes or connections that are not shown in
this handbook. Improper use of the appliance
can cause serious hazards, risking the safety of
personnel and of the installation.
• Use only original spare parts. Non-original spare
parts could cause re, electrical discharge or other
hazards.
• Before proceeding with installation, check the
supplied material to make sure it corresponds
to the order specication by examining the
identication labels (4.2 Product marking, page 2).
EN - English - Instruction manual
2 MNVKUCCMA_1635_EN
4 Identication
4.1 Product description and type
designation
Ceiling bracket for upside down mounting and
working of ULISSE COMPACT. Bracket with safety
chain and internal cable channel
4.2 Product marking
See the label attached to the product.
5 Preparing the product for
use
Any change that is not expressly approved
by the manufacturer will invalidate the
guarantee.
5.1 Unpacking
When the product is delivered, make sure that the
package is intact and that there are no signs that it
has been dropped or scratched.
If there are obvious signs of damage, contact the
supplier immediately.
Keep the packaging in case you need to send the
product for repairs.
5.2 Contents
Check the contents to make sure they correspond
with the list of materials as below:
• Upper bracket
• Lower bracket
• Covered steel cables
• Snap hook
• Eye-bolt
• Hook bolt
• Chain
• Sunshield
• Bracket for sunshield
• Equipment
• Instruction manual
5.3 Safely disposing of packaging
material
The packaging material can all be recycled. The
installer technician will be responsible for separating
the material for disposal, and in any case for
compliance with the legislation in force where the
device is to be used.
When returning a faulty product we recommend
using the original packaging for shipping.
Instruction manual - English - EN
3MNVKUCCMA_1635_EN
6 Installation
CAUTION! Device installation and
maintaining must be performed by
specialist technical sta only.
6.1 Brackets and pan & tilt
installation
Take special care when attaching and
fastening down the apparatus. If it is to be
attached to a concrete surface you must
use dowel pins with a traction torque rating
of at least 300dN each. For a metal surface
use screws with a diameter of at least 8mm
and of an appropriate length. The clamping
system must be able to support at least 4
times the weight of the entire equipment,
including P&T, lenses and camera.
Fix the upper bracket to the ceiling, centring it with
respect to the cable that must escape from the ceiling
by 1m.
Fig. 1
Fix the base of ULISSE COMPACT onto the lower
bracket adding Loctite 238 or equivalent.
Respect the orientation
visible in gure.
Fig. 2
Fix the eye-bolt to the base using the hole in the
lower bracket, positioning the split washer and
adding Loctite 238 or equivalent.
Fig. 3
Insert one end of the chain into the hook bolt hole
and then the eye-bolt, position the notched washer
and Loctite 238 or equivalent.
Fig. 4
Fig. 5
EN - English - Instruction manual
4 MNVKUCCMA_1635_EN
Insert the snap hook at the other end of the chain.
Insert the snap hook in the seat of the upper bracket.
Fig. 6
Fig. 7
The conguration in the gure is thus obtained.
Fig. 8
Connect the steel cables to the lower and upper
brackets as indicated in the following gures,
tightening with Loctite 238 (or equivalent). Fasten
with tightening torque of 4Nm.
Fig. 9
Fig. 10
The conguration in the gure is thus obtained.
Fig. 11
Instruction manual - English - EN
5MNVKUCCMA_1635_EN
Half way along the length of the chain, insert the
supplied cable for wiring recovery, making it pass
through the 2 holes in the bracket.
Fig. 12
Turn the lower bracket overmaking it turn as in the
gure.
Fig. 13
Fig. 14
Pass the power supply and signal cables through the
cable glands on the base. Use the clips supplied to
x the cables to the chain, but do not tighten it fully
home (the cable must be able to run inside).
Fig. 15
EN - English - Instruction manual
6 MNVKUCCMA_1635_EN
Wire the base (see ULISSE COMPACT manual). Tighten
the cable glands to the torque of 5Nm.
Now mount hte body of ULISSE COMPACT onto the
base, making sure that the 3 reference notches are
aligned to each other.
Fig. 16
Fix the body to the base using the 4 screws and
washers. Fasten with tightening torque of 4Nm.
Fig. 17
Overturn the entire pan & tilt, making it rotate.
Fig. 18
Fig. 19
Grip the pan & tilt with two hands in the area around
the base.
Fig. 20
Instruction manual - English - EN
7MNVKUCCMA_1635_EN
Insert the lower bracket into the upper one as in the
gure.
Fig. 21
Recover the cables before pushing the lower bracket
completely into the upper bracket.
Fig. 22
During this phase, prevent that chain and
cables remaining entangled between the
two brackets.
Fix the lower bracket to the upper one using the 6
screws and washers; add Loctite 238 threadlocks or
equivalent.
Fig. 23
6.2 Fixing the sunshield
Remove the sunshield from the housing.
Fig. 24
Secure the bracket to the housing.
Fig. 25
Mount the sunshield as in the image.
Fig. 26
EN - English - Instruction manual
8 MNVKUCCMA_1635_EN
Fig. 27
7 Disposal of waste
materials
This symbol mark and recycle system
are applied only to EU countries and not
applied to the countries in the other area of
the world.
Your product is designed and manufactured with
high quality materials and components which can be
recycled and reused.
This symbol means that electrical and electronic
equipment, at their end-of-life, should be disposed of
separately from your household waste.
Please dispose of this equipment at your local
Community waste collection or Recycling centre.
In the European Union there are separate collection
systems for used electrical and electronic products.
8 Technical data
8.1 General
Internal cable management
8.2 Mechanical
Made of galvanized and painted steel
Safety cord in AISI316L stainless steel
Unit weight: 6.4kg
8.3 Certications
EAC certication
Altri manuali per UCCMA
1
Indice
Lingue:
Altri manuali Videotec Rack e supporto
