Viessmann VITOCELL 100-B Manuale utente
Installation instructions
for contractors
VIESMANN
Vitocell 100-B
Type CVBA
Dual mode DHW cylinder 400/500 l
with Solar-Divicon
VITOCELL 100-B
5838690 GB 2/2019 Dispose after installation.
2
Please follow these safety instructions closely to
prevent accidents and material losses.
Safety instructions explained
Danger
This symbol warns against the risk of injury.
!Please note
This symbol warns against the risk of material
losses and environmental pollution.
Note
Details identified by the word "Note" contain additional
information.
Target group
These instructions are exclusively intended for quali-
fied contractors.
■Work on electrical equipment may only be carried
out by a qualified electrician.
Regulations to be observed
■National installation regulations
■Statutory regulations for the prevention of accidents
■Statutory regulations for environmental protection
■Codes of practice of the relevant trade associations
■Relevant country-specific safety regulations
Working on the system
■Isolate the system from the power supply (e.g. by
removing the separate fuse or by means of a mains
isolator) and check that it is no longer live.
■Safeguard the system against reconnection.
■Wear protective clothing.
!Please note
Electronic assemblies can be damaged by elec-
trostatic discharge.
Prior to commencing any work, touch earthed
objects such as heating or water pipes to dis-
charge static loads.
Danger
Hot surfaces can cause burns.
■Before maintenance and service work, switch
OFF the appliance and let it cool down.
■Never touch the hot surfaces of uninsulated
pipes and fittings.
Danger
Floors which are wet, damp or covered in fluids
containing glycol present a risk of injury through
slipping and falling.
■When carrying out installation and mainte-
nance work, ensure that the floor is kept clean
and dry.
■Wear non-slip shoes.
Danger
Breathing in or swallowing broken-off fragments
of insulating material may result in death by
asphyxiation.
■Do not allow children to play in the installation
room.
■Clean the installation room after installation
and maintenance work.
Repair work
!Please note
Repairing components that fulfil a safety func-
tion can compromise the safe operation of the
system.
Replace faulty components only with genuine
Viessmann spare parts.
Safety instructions
5838690
3
1. Information Disposal of packaging ............................................................................ 4
Symbols ................................................................................................. 4
Intended use .......................................................................................... 4
Product information ................................................................................ 5
■Vitocell 100-B, type CVBA ................................................................ 5
2. Installation information Product information ................................................................................ 6
■Connections ........................................................................................ 6
■Siting information ................................................................................ 6
3. Installation sequence Siting the DHW cylinder ......................................................................... 8
Fitting the Solar-Divicon and thermal insulation .................................... 8
■Removing the Solar-Divicon cover ..................................................... 8
■Fitting threaded studs and spacer sleeves ......................................... 9
■Fitting the thermal insulation jacket .................................................... 10
■Fitting the profile bracket .................................................................... 11
■Fitting the overflow pipe ...................................................................... 11
■Fitting the Solar-Divicon ..................................................................... 12
■Fitting the thermal insulation mat at the top ........................................ 12
■Route the cable. ................................................................................. 13
■Closing the thermal insulation ............................................................ 13
Connecting the immersion heater EHE ................................................. 15
Connecting the heating water side and solar side ................................. 15
■System scheme with solar collectors and boiler ................................. 16
Connections on the DHW side ............................................................... 17
■Safety valve ........................................................................................ 18
Install high limit safety cut-out (STB) ..................................................... 19
■Electrical connections ......................................................................... 19
■Setting the response temperature ...................................................... 20
■Reset high limit safety cut-out (STB) .................................................. 20
Connecting the equipotential bonding ................................................... 20
Commissioning ...................................................................................... 20
4. Specification ................................................................................................................ 21
Index
5838690
4
Please dispose of packaging waste in line with statu-
tory regulations.
Symbols
Symbol Meaning
Reference to other document containing
further information
1.
Step in a diagram:
The numbers correspond to the order in
which the steps are carried out.
Warning of material losses and environ-
mental pollution
Live electrical area
Pay particular attention.
■Component must audibly click into place.
or
■Acoustic signal
■Fit new component.
or
■In conjunction with a tool: Clean the sur-
face.
Dispose of component correctly.
Dispose of component at a suitable collec-
tion point. Do not dispose of component in
domestic waste.
Intended use
The appliance is only intended to be installed and
operated in sealed unvented systems that comply with
EN 12828 / DIN 1988, or solar thermal systems that
comply with EN 12977, with due attention paid to the
associated installation, service and operating instruc-
tions. DHW cylinders are only designed to store and
heat water of potable water quality. Heating water buf-
fer cylinders are only designed to hold fill water of pot-
able water quality. Only operate solar collectors with
the heat transfer medium approved by the manufac-
turer.
Intended use presupposes that a fixed installation in
conjunction with permissible, system-specific compo-
nents has been carried out.
Commercial or industrial usage for a purpose other
than heating the building or DHW shall be deemed
inappropriate.
Any usage beyond this must be approved by the man-
ufacturer for the individual case.
Disposal of packaging
5838690
5
Incorrect usage or operation of the appliance (e.g. the
appliance being opened by the system user) is prohibi-
ted and results in an exclusion of liability.
Incorrect usage also occurs if the components in the
system are modified from their intended use (e.g.
through direct DHW heating in the collector).
Adhere to statutory regulations, especially concerning
the hygiene of potable water.
Product information
Vitocell 100-B, type CVBA
■Enamelled DHW cylinder with internal indirect coil for
heating domestic hot water in conjunction with the
following:
–Solar thermal systems
–Floorstanding boilers
–Wall mounted boilers
–Heat pumps for dual mode operation
–Additionally, the use of an immersion heater is pos-
sible.
■Capacity: 400 and 500 l
■Suitable for systems conforming to DIN 1988,
EN 12828 and DIN 4753
Intended use (cont.)
5838690
6
Connections
A
B
C
D
E
F
G
H
Fig. 1
AFemale connection for immersion heater
BDHW with high limit safety cut-out
CCylinder temperature sensor
DHeating water flow
EDHW circ.
FHeating water return
GConnection for thermometer sensor
HCold water/drain outlet
Siting information
!Please note
The thermal insulation must not be able to come
into contact with naked flames.
Exercise caution when welding and soldering.
!Please note
To prevent material losses, install the DHW cyl-
inder in a room free from draughts and risk of
frost.
When not in use, the DHW cylinder must be
drained if there is a risk of frost.
■Provide adequate clearance from the wall so that the
Vitosolic 100 can be operated (if installed).
■Use the adjustable feet to level the DHW cylinder.
Note
Never extend the adjustable feet beyond a total
length of 35 mm.
Product information
5838690
7
Installation dimensions
a
A
Fig. 2
a Wall clearance
AFemale connection for immersion heater
650
260
260
310
(200) (150)
(150)
Fig. 3
Immersion heater installation instructions
Maintain the minimum clearance.
Note
The unheated length of any threaded immersion
heater installed on site must be at least 100 mm.
The threaded immersion heater must be suitable for
installation in enamelled DHW cylinders.
Product information (cont.)
5838690
8
Level the cylinder and fit the thermal insulation mat at
the bottom.
2.
1.
A
Fig. 4
ABag with type plate
Note
If no immersion heater is installed, seal the front
female connection with the plug supplied.
Fitting the Solar-Divicon and thermal insulation
Removing the Solar-Divicon cover
1.
Fig. 5
Siting the DHW cylinder
5838690
9
Fitting threaded studs and spacer sleeves
2.
1.
Fig. 6
1. Screw in threaded studs by hand as far as they will
go.
2. Slide on spacer sleeves.
Fitting the Solar-Divicon and thermal insulation (cont.)
5838690
10
Fitting the thermal insulation jacket
1.
5.
4.
2.
3.
Fig. 7
Note
■2 people are required for the following work.
■Ensure that no fleece remnants enter the DHW cylin-
der through the cylinder connections.
1. At the back of the cylinder: Attach 6 clip fasteners
to the edges of the right and left sections of the
thermal insulation jacket. Place the thermal insula-
tion jacket around the cylinder body.
Note
Leave the clip fasteners in the first notch.
2. At the front of the cylinder: Attach 5 clip fasteners
to the edges of the right and left sections of the
thermal insulation jacket. 3 clip fasteners at the
top, 2 at the bottom. Leave space for the Solar-Div-
icon.
3. Fit the thermal insulation jacket evenly around the
cylinder body by patting it.
4. Push the clip fasteners at the front of the cylinder
as close together as possible.
5. Push the clip fasteners at the back of the cylinder
as close together as possible.
Fitting the Solar-Divicon and thermal insulation (cont.)
5838690
Altri manuali per VITOCELL 100-B
9
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Viessmann Caldaia
Viessmann
Viessmann VITOGAS 100 Manuale di istruzioni
Viessmann
Viessmann VITODENS 050-W Guida rapida
Viessmann
Viessmann VITODENS 050-W Guida rapida
Viessmann
Viessmann Vitocaldens 222-F Manuale utente
Viessmann
Viessmann Vitocell 340-M Istruzioni operative
Viessmann
Viessmann VITOCROSSAL 300 Istruzioni operative
Viessmann
Viessmann VITOCELL 100-U Istruzioni operative
Viessmann
Viessmann Vitocrossal 300 CT3 SERIES Guida
Viessmann
Viessmann VITOCROSSAL 200 Manuale utente
Viessmann
Viessmann Vitodens 222-F Guida rapida
Viessmann
Viessmann Flue gas system Manuale utente
Viessmann
Viessmann VITODENS 200 Manuale utente
Viessmann
Viessmann VITOCAL 200-G Guida rapida
Viessmann
Viessmann Vitoflex 300-RF Series Manuale utente
Viessmann
Viessmann VITOCELL 100-U Istruzioni operative
Viessmann
Viessmann VITODENS 200 Guida
Viessmann
Viessmann Vitomax 200-LW M64A Manuale di formazione
Viessmann
Viessmann VITOLADENS 300-W Istruzioni operative
Viessmann
Viessmann VITOROND 200 Manuale utente
Viessmann
Viessmann Vitodens 100-W Manuale utente
