Viessmann VITOCELLV 300 Istruzioni operative
VITOCELLV 300
VITOCELLW 300
Service instructions
for heating engineers
VitocellV300 and VitocellW300
TypeEVA
DHW cylinders
130 to 200litres capacity
5692328GB12/2003 Please keep safe
2
General information
Safety instructions
Please follow these safety instructions closely to prevent accidents and
material losses. For safety instructions in conjunction with boilers, see
separate service instructions.
Work on the equipment
Installation, initial start−up, inspection,
maintenance and repairs must only
be carried out by a competent
person (heating engineer/installation
contractor).
Before working on the equipment/
heating system, isolate the mains
electrical supply (e.g. by removing a
separate mains fuse or by means of
a mains electrical isolator) and
safeguard against unauthorised
reconnection.
Repair work
It is not permitted to carry out
repairs on parts that fulfil a safety
function.
Use only original Viessmann spare
parts, or equivalent parts that have
been approved by Viessmann.
Initial start−up
The system must be commissioned
by the system installer or a qualified
person authorised by the installer.
Instructing the system user
The system installer must hand the
operating instructions to the system
user and instruct him/her in the
operation of the system.
¨Safety instructions
In this instruction manual, this
heading denotes information which
must be observed to prevent
accidents and material losses.
¨This symbol denotes information
which must be observed to
prevent material losses.
Product characteristics
The following standard characteristics and product characteristics determined
as system values for VitocellV300 and VitocellW300 (see table) can be utilised
for the energy assessment of heating and ventilation equipment to DINV470110
specified by the EnEV [Germany].
Capacity litres 130 160 200
Standby loss
qBS at 45K temp. differential
kWh/24h 1.3 1.4 1.6
5692328GB
3
Initial start−up, inspection and maintenance
Initial start−up
¨Initially fill the DHW cylinder from
the secondary side, then from the
primary.
If the secondary side of your DHW
cylinder cannot be filled yet, but
you want to commission your
heating system, then you can
operate your DHW cylinder with a
pressure of 2.5bar on the primary
side.
1. Fill the DHW cylinder from the
secondary side.
Please note:
The DHW cylinder cap does not
need to be tightened.
2. Check the compression fittings on
the primary and secondary side
for leaks and retighten, if
necessary.
3. Check the function of safety valves
according to manufacturer’s
instructions.
Inspection and maintenance
[In Germany,] DIN1988 requires a visual inspection and (if necessary)
cleaning no later than two years after the cylinder has been taken into use
and thereafter according to demand.
System shutdown
Checking electrical connections
Only if the DHW cylinder is not to be
cleaned on the inside:
Check the compression fittings on
the primary and secondary side for
leaks and retighten, if necessary.
Checking all safety equipment
Check the function of all safety
valves.
5692328GB
4
Initial start−up, inspection and maintenance
Inspection and maintenance (cont.)
Cleaning the inside of DHW cylinders
1. Drain the DHW cylinder from the
secondary side.
2. Remove top panelA, thermal
insulation matBand
thermometer sensorC.
3. Remove locking capD, internal,
circular stainless steel discEand
gasketF.
4. Disconnect the DHW cylinder
from the pipework to prevent any
cleaning agents and contaminants
entering the pipe system.
5. Remove loose deposits with a
high pressure cleaner.
¨Only use plastic tools to clean
the inside.
6. Use a chemical cleaning agent
to remove hard deposits that
cannot be removed by a high
pressure cleaner.
¨Safety instructions
Do not use cleaning agents
containing hydrochloric acid.
7. Thoroughly flush the DHW
cylinder after cleaning.
8. Reconnect the DHW cylinder to
the pipework.
9. A new gasketFmust be fitted
to locking capDevery time the
cylinder is opened.
10. Fit circular stainless steel discE,
locking capDand tighten down
with 160Nm.
11. Fill the DHW cylinder from the
secondary side.
12. Fit thermometer sensorC,
thermal insulation matBand
top panelA.
System restart
5692328GB
D
F
E
B
A
C
5
Parts list
Parts list
Spare parts information
Quote the type and serial no. of the
device (see type plate) and the item
no. of the required part (as per parts
list).
Obtain common parts from your
local supplier.
Parts
001 Top plate
002 Top insulating mat
003 Sensor retaining clip
004 Sensor retainer
005 Cylinder locking cap
(with item006 and 007)
006 Circular stainless steel disc
(with item007)
007 Gasket
008 Adjustable foot
010 Thermometer
012 Vitocell300 logo
013 Centering sleeve
Parts not shown
015 Installation instructions
018 Service instructions
019 Spray paint
020 Paint stick
AType plate
5692328GB
013
A
007
006
005
001
002
003
004
010
012
008
6
Parts list
5692328GB
7
Appendix
Commissioning/service report
Initial start−up Maintenance/service Maintenance/service
date:
by:
Maintenance/service Maintenance/service Maintenance/service
date:
by:
Maintenance/service Maintenance/service Maintenance/service
date:
by:
Maintenance/service Maintenance/service Maintenance/service
date:
by:
Maintenance/service Maintenance/service Maintenance/service
date:
by:
5692328GB
Viessmann Werke GmbH&Co
D35107 Allendorf
Tel: +49 6452 700
Fax: +49 6452 702780
www.viessmann.de
Viessmann Limited
Hortonwood 30, Telford
Shropshire, TF1 7YP, GB
Tel: +44 1952 675000
Fax: +44 1952 675040
E−mail: info−[email protected]
8
Appendix
Applicability
VitocellV300 and VitocellW300 (typeEVA)
130litres capacity
HVitosilver part no.7171641
160litres capacity
HVitosilver part no.7171640
HVitowhite part no.7171903
200litres capacity
HVitosilver part no.7171639
HVitowhite part no.7171904
5692328GBSubject to technical modifications.
Printed on environmentally friendly,
chlorine−free bleached paper
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Viessmann Caldaia
Viessmann
Viessmann Vitodens 200-W System Manuale utente
Viessmann
Viessmann Vitodens 300 Istruzioni operative
Viessmann
Viessmann VITOLIGNO 300-P Manuale utente
Viessmann
Viessmann Vitodens 100-W Guida rapida
Viessmann
Viessmann Vitogas 100 GS1 Series Manuale utente
Viessmann
Viessmann VITOLIGNO 300-C Istruzioni operative
Viessmann
Viessmann VITOCELL 300W Manuale utente
Viessmann
Viessmann Vitodens 200-W System Istruzioni operative
Viessmann
Viessmann VITOLADENS 300-T Istruzioni operative
Viessmann
Viessmann Vitodens 200-W System Istruzioni operative
Viessmann
Viessmann VITODENS 050-W Manuale utente
Viessmann
Viessmann Vitodens 242-F Guida rapida
Viessmann
Viessmann VIESMANN VITOLIGNO 300-H Guida rapida
Viessmann
Viessmann Vitorond 100 Istruzioni operative
Viessmann
Viessmann Multiple Vitodens Systems Manuale elenco delle parti
Viessmann
Viessmann VITODENS 200-W WB2B 80 Manuale utente
Viessmann
Viessmann VITORONDENS 200-T Istruzioni operative
Viessmann
Viessmann Vitodens 300 Manuale utente
Viessmann
Viessmann Vitodens 242-F Guida rapida
Viessmann
Viessmann Vitocell 140-E Guida rapida
