Vip-Vision SLR-A75 Series Manuale utente
SLR-A75 Series
Solar Surveillance Installation Guide
Version 230818
Thank you for purchasing a SLR-A75 Series Solar Surveillance System.
This install guide covers basic setup, installation and use of your surveillance system.
For more information, please visit:
www.vip-vision.com
WiFi Solar Surveillance System (SLR-A75-4W)
4G Solar Surveillance System (SLR-A75-4G)
2Crucial evidence. Always.
SLR-A75 Series | Solar Surveillance
1. Pre-install Information
#Part Product Code Image
1x Solar Panel
(Optional remote control device) SSL-A40MN
1x 4.0MP Mini PTZ Dome Camera VSIP4MPPTZMINI
1x Camera Adapter VSBKTA106
1x Right Angle Bracket VSBKTB305W
1x Junction Box VSBKTA140
1x Pole Mount Bracket VSBKTA150
1x 128GB microSD card MICROSD128GB
2x
Ubiquiti 5.8GHz 120° Wireless Bridge
(1x Access Point, 1x Station)
(WiFi system only) WT5-ULB
1x Huawei 4G Modem Router with WiFi
(4G system only) VSWAN4GHW
1.1 Included components
Pole, base plate & SIM card not included.
Required Install Tools: Allen key for junction box (included), 4mm & 10mm Allen keys
for solar panel (not included), 8mm drill bit & battery drill, flat head screwdriver. Laptop
with RJ45 network interface strongly recommended for camera setup.
3
www.vip-vision.com
1. Pre-install Information
Professional Series 4.0MP 4x Zoom Mini PTZ Dome
Note: Camera has been preinstalled with the supplied 128GB microSD card and has been
preconfigured to record 4.0MP (2592 x 1520) at 25fps.
The username and password details for the camera can be found on the configuration
sheet inside the junction box. The default username is admin.
To prevent unauthorised access, ensure you change the admin password before completing
installation.
Default Camera Configuration
Main Stream
Stream Type General
Encode Type H.265
Resolution 2592x1520
FPS 25
StreamCTRL VBR
Quality 6 (Best)
Ref Stream 1536-8192Kbps
I Frame Interval 50
Watermark Yes
Characters DigitalCCTV
Sub Stream
Stream Type General
Encode Type H.265
Resolution 704x576 (D1)
FPS 10
StreamCTRL CBR
Bit Stream 512Kbps
Ref Stream 139-768Kbps
I Interval 20
SVC 1 (off)
1.2 Camera Information
4Crucial evidence. Always.
SLR-A75 Series | Solar Surveillance
Motion Sensing Solar Panel with 40W Street Light
Panel Type 75W monocrystalline silicon panel
Battery 41.6Ah Lithium Iron Phosphate (LiFiPo 4) with Low Voltage Cutoff
Panel Tilt Adjust -60° ~ 60°
Ingress Protection (Panel) IP66
Wind Tolerance Up to 65m/s
Dimensions (Panel) 1063 x 259 x 526mm
Pole Diameter (Spigot) Ø60mm
Note: This solar panel system is fitted with undervoltage protection, which disconnects
the load at approximately 10.8V. If you are not receiving any voltage on the output wires,
place the panel in direct sunlight for a minimum of one hour and re-test. The output will be
reconnected automatically when battery voltage reaches approximately 11.5V.
Must be installed in direct sunlight. Shade will negatively impact performance.
This solar panel includes a motion-activated LED light which is disabled by default. For
more information, refer to 4. Solar Panel LED Configuration (p16).
LED light configuration requires the solar panel remote control (provided on request).
1.3 Solar Panel Information
5
www.vip-vision.com
526mm 1063mm
259mm
M8*30 x 4
M6 O x 4
M6
M6*15
M8 x 4
M6 O x 2
M
M6*16 x 2
M8
M8
M8*2
6 C x 2
O x 2
C x 2
0 x 2
x 4
C x 4
M8*3
M
Φ50-60mm
8 x 4
0 x 4
Solar Panel Dimensions
Solar Panel Screw Diagram
1. Pre-install Information
North
6Crucial evidence. Always.
SLR-A75 Series | Solar Surveillance
2.1 Mounting the solar panel to the pole
1. Drill an 8mm hole in the pole
(minimum 15cm down from the
top of the pole) on the same side
that the camera will be mounted.
This is for the solar panel cable to
run through. The position of the
hole will vary depending on what
position on the pole the camera is
to be mounted.
2. Feed the twin power cable
connected to your solar panel
through that hole
3. Place the solar panel bracket on
top of the pole, pointing north.
• Note: If you need to cover a
different area with the light
beam, keep the panel flat after
repositioning .
4. Securely fasten the included grub
screws to the bracket. Tighten the
locking bolts to prevent the grub
screws from loosening. (Fig. 2.1b)
• Note: For poles greater than
4m in height, tapered poles are
preferable for camera stability and
pole strength.
2. Installation
8mm
Fig. 2.1a
Solar panel power cable drill location
Fig. 2.1b
Installed grub screws
Caution: Solar panel must be placed so it is in direct sunlight all day.
Any shading will greatly reduce the solar panel’s performance!
7
www.vip-vision.com
2.2 Adjusting solar panel angle
1. Use a flat head screwdriver to remove the bracket cover (Fig. 2.2a).
2. Once the cover is removed, loosen the Allen head to adjust the solar panel angle (Fig. 2.2b).
To ensure your solar panel absorbs as much light as possible, it’s important to adjust the solar panel
angle to an ideal angle, depending on your region (refer to table below).
3. Tighten the bolt after adjusting the angle to secure the solar panel in place.
4. Replace the cover.
Note: Ideally, the panel must point north with the correct angle from the table above. Please contact
VIP Vision for cities outside of Australia.
To ensure the solar panel works efficiently, it will require regular cleaning. The lower the angle the
solar panel is positioned (flatter), the more often it will need to be cleaned.
Ideal panel angles (H°) by Australian city
Sydney Melbourne Perth Brisbane Hobart Adelaide Darwin
34° 38° 32° 27.5° 43° 35° 12.5°
Fig. 2.2a
Solar panel angle adjust cover
Fig. 2.2b
Solar panel angle adjust Allen head
2. Installation
8Crucial evidence. Always.
SLR-A75 Series | Solar Surveillance
A
B
C
D
E
65-89mm
Band Clamps
F
2.3 Mounting the camera to the pole
#Part Product Code
A Camera VSIP4MPPTZMINI
B Camera Adapter VSBKTA106
C Right Angle Bracket VSBKTB305W
D Junction Box VSBKTA140
E Pole Mount Bracket VSBKTA150
F Pole Not supplied
The camera, camera adapter, right angle bracket and junction box are already connected (A, B, C & D).
• Mount the pole mount bracket to the pole first.
• After the pole mount is installed, mount the junction box to the pole mount.
• Open the junction box and tighten the screws inside to securely fasten it to the pole mount.
9
www.vip-vision.com
1. Mount the pole mount bracket onto the pole using 3 included band clamps (Fig. 2.3b).
Note: The 3 included band clamps are 65-89mm for poles 50-60mm in diameter. If installing on a
thicker pole (eg. 80-150mm), larger band clamps will be required.
Fig. 2.3a
Mounted pole bracket (front)
Fig. 2.3b
Mounted pole bracket (back)
Fig. 2.3c
Junction box interior (no 4G router)
2. Open the junction box (Fig. 2.3c).
Note: This image shows the inside of the junction box as seen with the WiFi kit.
The 4G kit will also have the 4G router pre-installed inside the junction box.
2. Installation
10 Crucial evidence. Always.
SLR-A75 Series | Solar Surveillance
4. Run the power cable coming from the solar panel through one of the cable holes of the junction
box.
5. Carefully connect the solar panel power cable to the terminal block, with the red wire
connecting to + and the black wire connecting to -. (Fig. 2.3f)
Fig. 2.3f
Solar battery cables connected to terminal block
Fig. 2.3e
Terminal block
Caution: Do not allow the negative and positive power supply wires from the solar
panel to touch (short circuit) - this will cause the lithium polymer battery to enter protection
mode and output voltage will drop to 0V.
The only way to recover from this is to disconnect and then reconnect the battery inside the
panel - Please contact VIP Vision™ for further details.
When running cables, insulation should be removed from each end and cut carefully,
ensuring each end does not touch each other.
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Vip-Vision Sistema di sicurezza
Manuali Sistema di sicurezza popolari di altre marche
EDM
EDM Solution 6+6 Wireless-AE Manuale utente
Highway Safety Group
Highway Safety Group EA401 Manuale utente
Siren
Siren LED GSM Manuale utente
Detection Systems
Detection Systems 7090i Istruzioni per il montaggio
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Manuale utente
Siemens
Siemens FDM273 Manuale utente