Viptela vEdge 2000 Manuale utente
vEdge 2000 Router
The vEdge 2000 router delivers highly secure site-to-site data connectivity to large enterprises, offers interface
modularity, and provides the following features:
• 1RU, standard rack mountable in a 19-inch rack
• Support for AC input power
• Four built-in 1-Gigabit Ethernet SFP ports (4x1-Gigabit Ethernet)
• Two Pluggable Interface Module (PIM) slots that support two types of PIMs:
• Eight ports of 1-Gigabit Ethernet (8x1-Gigabit Ethernet)
• Two ports of 10-Gigabit Ethernet (2x10-Gigabit Ethernet)
• Encryption and QoS support
• 10-Gbps forwarding throughput (inclusive of encryption)
• Secure identification chip for anti-counterfeit and secure authentication
• Redundant hot-swappable fan tray modules
• Dual redundant hot-swappable power supply slots
• Front to back cooling
Chassis Views
Figure 1 and Figure 2 show the front and back panels of the vEdge 2000 router, indicating the location of the
power interfaces, module slots, status indicators, and chassis identification labels.
Figure 1: Front Panel of the vEdge 2000 Router
vEdge 2000 Router
1
Figure 2: Back Panel Slots and Connectors of the vEdge 2000 Router
•Declaration of Conformity, on page 2
•Components and Specifications, on page 3
•Planning and Installation, on page 25
•Maintenance and Troubleshooting, on page 41
Declaration of Conformity
The Viptela products are controlled under the Commerce Control List (CCL) of the U.S. Export Administration
Regulations (EAR) as networking equipment within the following U.S. Export Control Classification Numbers
(ECCN): 5A002, 5D002, and 5E002.
The vEdge hardware and software products and the Viptela encryption technology can be delivered to most
end users and destinations worldwide without a licensing requirement. The Viptela solution and products
have undergone a one-time review by the Government of the United States of America and qualify for License
Exception ENC. As such, they are eligible for export according to Section 740.17 of the EAR.
The Viptela solutions and products can be delivered to most end users worldwide, except to entities or end
users in the following countries: Cuba, Iran, North Korea, Sudan, and Syria.
vEdge 2000 Router
2
vEdge 2000 Router
Declaration of Conformity
Controlled Technologies
Viptela manages technology subject to the U.S. Export Administration Regulations (EAR). These controlled
technologies may include items under U.S. ECCN 5E002 encryption technology. The Viptela encryption
technology is for the development, production, and use of Viptela products that implement or use encryption.
The Viptela software distribution policy allows only authenticated users to download the Viptela encryption
software. Recipients of controlled technology are obliged to maintain adequate controls to prevent nationals
from outside the U.S. and Canada from accessing Viptela information, subject to ECCN5E002, without first
obtaining authorization from the U.S. government.
For additional information on controlled technologies, please contact Viptela support at [email protected]
.
Components and Specifications
This article provides the chassis specifications of the vEdge 2000 router and lists the other router components.
Chassis Specifications
Table 1 lists the specifications for the vEdge 2000 router chassis.
Table 1: vEdge 2000 Router Chassis Specifications
Table 1:
SpecificationItem
Services and Slot Density
4
Fixed SFP-based traffic ports (max 1 Gbps)
2Pluggable Interface Module (PIM) slots
YesEmbedded hardware-based crypto acceleration (IPSec)
8 GBMemory DDR3 ECC DRAM
Maximum capacity supported 32 GBSD card slot (external)
8 GBNAND storage (internal)
2External USB flash memory slots (Type A USB 3.0)
1USB console port (Type B default 115.2 Kbps)
1Serial console port (RJ-45 default 115.2 Kbps)
1Management Ethernet port (RJ-45 10/100/1000 Mbps)
Hot-swappable Power Supply Units (PSUs)Power supply option
Active–Active redundancyRedundant power supply support
Power Specifications
vEdge 2000 Router
3
vEdge 2000 Router
Components and Specifications
SpecificationItem
100-240 Volts
AC input voltage
50-60 HzAC input line frequency
125 WattsTypical power consumption
Physical Specifications
1.75 in. (4.45 cm)
Chassis height
Chassis only: 17.25 in. (43.82 cm)
Chassis with mounting brackets attached: 19 in.
(48.2 cm)
Chassis width
18.5 in. (47 cm)Chassis depth
1 RURack height
Provided with the unitRack-mount accessory kit 19 in (48.3 cm)
Chassis only: 11 lb (5 kg)
Chassis with two power supplies installed: 15 lb (6.8
kg)
Weight
Front to backAirflow
Packaging Specifications
8.5 in. (21.6 cm)
Package height
22 in. (55.88 cm)Package width
23.5 in. (59.7 cm)Package depth
Operating Condition
0 to 40°C (32 to 104°F) at sea level ( temperature
de-rating of 1.5 deg C per 1000 feet of altitude
applicable up to max of 10000 feet or 3000 m)
Temperature
Max 3000 m (10000 ft)Altitude
10 to 85% RHHumidity
Transportation/Storage Condition
-40 to 70°C (-40 to 158°F)
Temperature
5 to 95%RHHumidity
4570 m (15000 ft)Altitude
Reliability
vEdge 2000 Router
4
vEdge 2000 Router
Components and Specifications
SpecificationItem
420K hours
MTBF
Regulatory Compliance
AS/NZS 60950-1 CAN/CSA 60950-1
CB-IEC60950-1 CE Marking EN 60950-1
UL60950-1
Safety
AS/NZS CISPR22 Class A EN 300 386 EN 55022
Class A FCC Class A ICES Class A VCCI Class A
EMC
ROHS 6/6Environmental
Router Components
For a description of the vEdge 2000 router components, read these articles:
Front Panel Components Router Modules Ports and Connectors Power Supply and Cooling System
Field-Replaceable Units
Front Panel Components
This article describes the LEDs, reset button, and the SD card slot on the front panel of the vEdge 2000 router.
See At a Glance for the exact location of these components on the front panel of the router.
LEDs
The vEdge 2000 router has four chassis status LEDs located in the center of the front panel next to the USB
ports. See Figure 1.
Figure 1: Chassis Status LEDs in a vEdge 2000 Router
The following table describes the LEDs , their color and states, and the status they indicate.
vEdge 2000 Router
5
vEdge 2000 Router
Front Panel Components
Table 2:
DescriptionColorLED
• Off: System is off
• Green: System is healthy and operating
correctly
• Blinking Green: System is booting up
• Red: Major failure or alarm is present
Green/Amber/RedSYS
• Off: Status of OMP to vSmart controller is
down
• Green: Status of OMP to vSmart controller is
up
GreenSTAT
• Off: Power supply unit 1 is not present, or
router is not powered
• Green: 12-Volt output is OK on power supply
unit 1
• Red: Fault on power supply unit 1, or only
power supply unit 0 is connected
Green/RedPWR 1
• Off: Router is not powered
• Green: 12-Volt output is OK on power supply
unit 0
• Red: Fault on power supply unit 0, or only
power supply unit 1 is connected
Green/RedPWR 0
Reset Button
The front panel of the vEdge 2000 router has a reset button. The reset button is recessed to avoid accidentally
pressing it while the router is operational. To press the reset button, use a sharp narrow tool. Table 2 describes
the effects of pressing the reset button.
Table 3:
BehaviorPress
Duration
Pressing for two seconds resets and reboots the router.Short press
Pressing for 10 seconds resets the router and reboots it with factory default configuration.Long press
vEdge 2000 Router
6
vEdge 2000 Router
Front Panel Components
SD Card Slot
The front panel of the vEdge 2000 router has an SD card slot. The SD card slot has the following specifications:
• High speed bus: maximum 25 MB/second
• Supported card types: SD, SDHC
PIM and Transceiver Modules
This article describes the Pluggable Interface Modules (PIMs) for the vEdge 2000 router as well as the SFP
and SFP+ transceivers for those PIMs.
PIMs for the vEdge 2000 Router
The vEdge 2000 router offers interface modularity, providing two PIM slots that support two types of PIMs:
• 8x1-Gigabit Ethernet SFP PIM (Model: PIM-8x1GE-SFP)
• 2x10-Gigabit Ethernet SFP+ PIM (Model: PIM-2x10GE-SFP+)
The two PIM slots are labeled PIM Slot 0 and PIM Slot 1.
Figure 1 and Figure 2 show the front panel of the 8x1-Gigabit Ethernet SFP PIM and the 2x10-Gigabit Ethernet
SFP+ PIM, respectively.
Figure 1: Front Panel of 8x1-Gigabit Ethernet SFP PIM
Figure 2: Front Panel of 2x10-Gigabit Ethernet SFP+ PIM
vEdge 2000 Router
7
vEdge 2000 Router
PIM and Transceiver Modules
The status LED on the front panel indicates the status of the PIM (see Table 1). For an explanation of the
LAN/WAN LED and the Link/Activity/Status LED, see Network Port LEDs .
Table 4:
DescriptionLED
State
• The PIM module is offline.
• The router is powered off.
Off
• The PIM module is online and functioning normally.Green
• The PIM module is online but is not functioning
normally.
Red
Note: You can install the 8x1-Gigabit Ethernet SFP PIM in either PIM Slot 0 or PIM Slot 1. However, when
it is installed in PIM Slot 0, only four ports are usable. When it is installed in PIM Slot 1, all eight ports are
usable. There is no such restriction with the 2x10-Gigabit Ethernet SFP+ PIM. For details, see Interface Port
Combinations for the vEdge 2000 Router below.
Interface Port Combinations for the vEdge 2000 Router
A vEdge 2000 router has four fixed 1-Gigabit Ethernet interfaces, and you can install one or two PIM modules
for additional interfaces.
You can combine the fixed interfaces and the PIM modules as follows:
• Two 2x10-Gigabit Ethernet SFP+ PIMs. This combination allows you to configure four 10-Gigabit
Ethernet interfaces. This would give you a total of four 10-Gigabit Ethernet interfaces and four 1-Gigabit
Ethernet interfaces in the router.
vEdge 2000 Router
8
vEdge 2000 Router
PIM and Transceiver Modules
• One 2x10-Gigabit Ethernet SPF+ PIM (in PIM Slot 0) and one 8x1-Gigabit Ethernet SPF PIM (in PIM
Slot 1). This combination allows you to configure two 10-Gigabit Ethernet interfaces and eight 1-Gigabit
Ethernet interfaces. This would give you a total of two 10-Gigabit Ethernet interface and twelve 1-Gigabit
Ethernet interfaces in the router.
•Two 8x1-Gigabit Ethernet SFP PIMs. This combination allows you to configure twelve 1-Gigabit Ethernet
interfaces. This would give you a total of sixteen 1-Gigabit Ethernet interfaces in the router.
Table 5:
Total 1GE InterfacesTotal 10GE
Interfaces
PIM Slot 1PIM Slot 0
4 (fixed)42x10-Gigabit Ethernet SFP+
PIM
2x10-Gigabit Ethernet
SFP+ PIM
12 (8 on PIM plus 4 fixed)28x1-Gigabit Ethernet SFP PIM2x10 Gigabit Ethernet SFP+
PIM
16 (12 on PIM plus 4
fixed)
08x1-Gigabit Ethernet SFP PIM8x1-Gigabit Ethernet SFP PIM
When the 8x1-Gigabit Ethernet SFP PIM is in PIM Slot 0, only the first four ports are usable; the remaining
four ports are unusable.
Changing PIM Types
If you change the type of PIM that is installed in a vEdge 2000 router slot from a 1-Gigabit Ethernet to a
10-Gigabit Ethernet PIM, or vice versa, possibly as part of an RMA process, follow these steps:
1. Delete the configuration for the old PIM (the PIM you are removing or returning as part of the RMA
process).
2. Remove the old PIM.
3. Insert the new PIM (the PIM you received as part of the RMA process).
4. Reboot the vEdge 2000 router.
5. Configure the interfaces for the new PIM.
Supported Transceiver Modules
The built-in Gigabit Ethernet network ports on the vEdge 2000 router and the network ports on the 8x1-Gigabit
Ethernet SFP PIM support SFP transceivers. The 10-Gigabit Ethernet ports on the 2x10-Gigabit Ethernet
SFP+ PIM support SFP+ transceivers.
This section describes the optical interfaces supported for the SFP and SFP+ transceivers and the copper
interfaces supported for the SFP transceivers.
Note: It is recommended that you use the optical transceivers and optical connectors purchased from Viptela
for your vEdge routers.
The tables below describe the optical interface support over single-mode fiber-optic (SMF) and multimode
fiber-optic (MMF) cables for SFP and SFP+ transceivers and over the copper interface for SFP transceivers.
vEdge 2000 Router
9
vEdge 2000 Router
PIM and Transceiver Modules
Table 6:
ValueSpecificationEthernet Standard
SFP-1GE-Base-TModel Number1000 BASE-T
10/100/1000
Mbps
Rate
RJ-45Connector Type
N/AFiber Count
N/ATransmitter Wavelength
N/AMinimum Launch Power
N/AMaximum Launch Power
N/AMinimum Receiver
Sensitivity
N/AMaximum Input Power
CopperCable Type
100 m (328 ft)Distance
Not availableDOM Support
SFP-1GE-SX
Model Number1000 BASE-SX
1000 MbpsRate
LCConnector Type
DualFiber Count
850 nmTransmitter Wavelength
-9.5 dBmMinimum Launch Power
-3 dBmMaximum Launch Power
-21 dBmMinimum Receiver
Sensitivity
0 dBmMaximum Input Power
MMFFiber Type
220 m (721 ft) to 550 m (1804 ft) depending on fiber core
size/modal bandwidth specification
Distance
AvailableDOM Support
SFP-1GE-LX
Model Number1000 BASE-LX
vEdge 2000 Router
10
vEdge 2000 Router
PIM and Transceiver Modules
Indice
Altri manuali Viptela Router di rete
Manuali Router di rete popolari di altre marche
NETGEAR
NETGEAR FS526T - Switch Manuale utente
Korenix
Korenix JetNet 5710G Series Manuale utente
Automated Logic
Automated Logic ZN551 Manuale del proprietario
Cisco
Cisco ASR 1000 Series Manuale dell'operatore
EnGenius
EnGenius ESR-9710 Manuale utente
Cisco
Cisco 805 Series Istruzioni operative e di sicurezza