Vision TECHCONNECT TC2-MATRIXBRIDGE Manuale utente
2
TC2-MATRIXBRIDGE_manual_en
DECLARATION OF CONFORMITY
Where applicable Vision products are certified and comply with all known local regulations to a
„CB Certification‟ standard. Vision commits to ensure all products are fully compliant with all
applicable certification standards for sale in the EU and other participating countries.
The product described in this owner manual is in compliance with RoHS (EU directive
2002/95/EC), and WEEE (EU directive 2002/96/EC) standards. This product should be returned
to the place of purchase at the end of its useful life for recycling.
WARNINGS
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the
user to the presence of uninsulated “dangerous voltage” within the product‟s enclosure that may be
of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle, is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature accompanying the
appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
All products are designed and imported into the EU by „Vision‟ who is wholly owned by „Azlan
Logistics Ltd.‟, Registered in England Nr. 04625566 at Lion House, 4 Pioneer Business Park,
Clifton Moor, York, YO30 4GH. WEEE Registration: GD0046SY
DECLARATION OF ORIGIN
All Vision products are made in the People‟s Republic of China (PRC).
3
TC2-MATRIXBRIDGE_manual_en
USE ONLY DOMESTIC AC OUTLETS
Connecting the unit to an outlet supplying a higher voltage may create a fire hazard.
HANDLE THE POWER CORD WITH CARE
Do not disconnect the plug from the AC outlet by pulling the cord; always pull the plug itself.
Pulling the cord may damage it. If you do not intend to use your unit for any considerable
length of time, unplug the unit. Do not place furniture or other heavy objects on the cord, and
try to avoid dropping heavy objects on it. Do not tie a knot in the power cord. Not only could
the cord be damaged, but a short circuit could also be caused with a consequent fire hazard.
PLACE OF INSTALLATION
Avoid installing this product under the following conditions:
• Moist or humid places
• Places exposed to direct sunlight or close to heating equipment
• Extremely cold locations
• Places subject to excessive vibration or dust
• Poorly ventilated places
Do not expose this product to dripping or splashing. DO NOT PLACE OBJECTS FILLED WITH
LIQUIDS ON OR NEAR THIS PRODUCT!
MOVING THE UNIT
Before moving the unit, be sure to pull out the power cord from the AC outlet and disconnect
the interconnection cords with other units.
WARNING SIGNS
If you detect an abnormal smell or smoke, turn this product off immediately and unplug the
power cord. Contact your reseller or Vision.
PACKAGING
Save all packing material. It is essential for shipping in the event the unit ever needs repair.
IF ORIGINAL PACKAGING IS NOT USED TO RETURN THE UNIT TO THE SERVICE CENTRE,
DAMAGE IN TRANSIT WILL NOT BE COVERED BY WARRANTY.
4
TC2-MATRIXBRIDGE_manual_en
OVERVIEW
This product is a protocol exchange device which allows 3rd party software to control the
Techconnect Matrix devices.
Only one of these devices is required per system.
Provides built-in web server and Telnet API (used in a third-party controller)
Detects TX/RX automatically
Supports matrix switching
Supports Video Wall
Standards and protocols: HTTP, TCP/IP, Multicast
5
TC2-MATRIXBRIDGE_manual_en
FRONT PANEL
4
1. Power LED - steady red when the device is powered on
2. WORK LED - steady blue when the device is working properly. If red the device is
rebooting.
3. RESET button - When the device is powered on, press and hold this button for 5
seconds to restores to factory default settings.
4. Label - Write down the IP address of the device on the label which comes with the
device.
REAR PANEL
5 6 7
5. ETHERNET - RJ45 Port
6. RS232 –For debugging
7. Power 5V / 2A DC power supply input
6
TC2-MATRIXBRIDGE_manual_en
HARDWARE INSTALLATION
1. Connect all transmitters, receivers, and the bridge to the network.
2. Connect Source to TX
3. Connect Displays to RX
4. Power on all the devices
5. Use Telnet or Web browser to manage bridge.
tv
Apple TV Xbox
TX
TVTV
RX
PC
Switch
HDMI
Ethernet
TX RX
IP Control Box
7
TC2-MATRIXBRIDGE_manual_en
SETUP
Users can access the device through Web, Telnet or a Third-party controller.
Web
To access the device through Web Management Page, follow these steps.
1. Enter 192.168.11.243 into a browser.
2. Enter a password (“admin”by default), click Login to access the device.
Notes:
The IP address of the computer and IP Control Box should be in the same network subnet.
For example, if the IP address of IP Control Box is 192.168.11.243, then the computer
should be 192.168.11.X.
The IP address of the IP Control Box can be changed through Web Management Page or
Telnet.
If the Web Management Page cannot be displayed, please refer to FAQ.
8
TC2-MATRIXBRIDGE_manual_en
Telnet
To access the device through Telnet, follow these steps.
1. Click Start menu, go to Run. Input cmd, click OK.
2. Input telnet 192.168.11.243, press Enter.
This window will come up:
Notes:
The IP address of the computer and IP Control Box should be in the same network subnet.
For example, if the IP address of IP Control Box is 192.168.11.243, then the computer
should be 192.168.11.X.
If you use a third-party controller, you can access the device refer to the document API
Command.
9
TC2-MATRIXBRIDGE_manual_en
WEB CONFIGURATION
The Web Management Page is designed to perform the functions to control the device in a user-
friendly interface.
Home Screen
Open your browser, enter 192.168.11.243 in the address bar, and input the password (admin by
default), click Login.
This window will open:
It includes three parts: Matrix, TX/RX Settings and System Settings.
10
TC2-MATRIXBRIDGE_manual_en
Matrix
Click Load Matrix button, a table comes up.
The first row shows TX, the first column shows RX.
Icon
Description
device is online.
device is offline.
Shows TX and RX are linked. Click the green bar; it changes into blank,
which means TX and RX are disconnected.
The red bar represents TX/RX connecting is in processing.
The white bar represents correspondence TX and RX are not linked.
You can link them by clicking this white bar.
Indice
Altri manuali Vision Hardware di rete
Manuali Hardware di rete popolari di altre marche
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuale utente
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuale utente
Yudor
Yudor YDS-16 Manuale utente
D-Link
D-Link ShareCenter DNS-320L Manuale utente
Samsung
Samsung ES1642dc Istruzioni per l’uso
Honeywell Home
Honeywell Home LTEM-PV Istruzioni per il montaggio
