Vision ZA1002US-5 Manuale operativo
ZA1002US-5
Z-Wave Smart Gateway
Installation&UserGuide
(ForPC)
1
WELCOME
Congratulations on purchasing the ZA1002US-5. The ZA1002US-5 integrates multiple
complicated control, automation and internet protocols into one simple plug-and-play device.
It is a central controller that integrated and control of all wireless Z-wave devices used for
home automation and keeps connect and control of your home easily, nomatter where you
are.Please take a few minutes toread this guide to set up your ZA1002US-5 and Z-wave
network smoothly.
2
Table of Contents
Chapter 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . 4
1.1 Key Features . . . . . . .. . . . . . . . . . . . . . . . . . . . . .. . . . .. . . . . . . . . . . . . . . . . . . . . . . . .. . . 4
1.2 .Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . 4
1.3 .Hardware Overview . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . .. . . . . . . . . . . . . . . . . . 5
1.3.1 Front Panel . . . . . .. . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . 5
1.3.2 Back Panel . . . . . .. . . . . . . .. . . . . . . . . . . . .. . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . 6
Chapter 2 Quick Install. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . 7
2.1 Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . .7
2.2 The Procedure of Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
2.3Find the IP address of your
ZA1002US-5 . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . .. . . . .. . . . .8
2.4 Setup Wi-Fi for your
ZA1002US-5. . . . . . . . . . . . . . . . . .. . . . . . . . . . . . .. . . . . . . . . . . . . . . . .. . . . .. . . . .8
2.4.1 System. . . . . . . . . . . . . . . . . .. . . . . . . . . . .. . . . . ... . . . . ... . . . . .. . . . . . . . . . . . .. . . . .. . . . .9
2.4.2 Network. . . . . . . . . . . . ... . . . . ... . . . . ... . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . .. . . . .. . . . .10
2.4.2.1 General Setup. . . . . . .. . . . . ... . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . .. . . . .. . . . .10
2.4.2.2 Advanced Settings. . . . . . . . . . . . . . . . . ... . . . . .. . . . . . . . . . . . . . . . . . . . . . .. . . . .. . . . .11
2.4.2.3 Physical Settings. . . . . ... . . . . ... . . . . ... . . . . .... . . . ... . . . . ... . . . . ... . . . . ... . . . ..12
2.4.2.4 Firewall Settingsb. . . ... . . . . ... . . . . ... . . . . ... . . . . ... . . . . ... . . . . ... . . . . ... . . . . ..12
2.4.3 Zwave. . . . . ... . . . . ... . . . . ... . . . . ... . .... . . . . ... . . . . ... . . . . ... . . . . ... . . . . ... . . . . ..13
2.4.4 Logout. . . . . . . . . .. . . . . . . . . .. . . . . . . . . .. . . . . . . . . .. . . . . . . . . .. . . . . . . . .. . . . . . . . . 13
2.5Initial setup procedure for ZA1002US-5 web
configuration . . . . . . . . . . .. . . . . . . . . . . . . . .. . . .. . . . .14
Chapter 3 Full web configurations . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . .. . . . . . . .15
3.1 Enter web configure page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.2 SetZwave– Z-Wave device settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.2.1 The Z-Wave device configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.2.1.1 Add a Z-Wave device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 17
3.2.1.2 Remove a Z-Wave device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.2.2 Z-Wave Control and Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . .21
3.2.3 Topology . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . .. . . . . . . . . . . . . . . . . . . .. . . . . . . . 22
3.2.4 Door Lock Security . . . . . . . .. . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . .23
3.2.5 Version Information . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3.3 Room Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3
3.3.1 Create Room . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3.3.2 All Rooms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.4Device Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
4
Chapter 1 Introduction
ZA1002US-5is a central controller that integrated and control of all wireless Z-wave devices
used for home automation. It also providesGateway to connect to Internet. ThroughInternet
you can see all kinds of devices status of your home atanytimeand any place via your
smartphone or PC.You can control thehomedevices such aslighting, air conditioning, door
lock and unlock, you can also receivethealarmmessageof your home. Energy usage
monitorsof your homeat any timeis real-timerecordingto the cloudhost, homealarm
messagesareimmediatelydeliveredto the cloudmessagemonitoring
centerforthenecessarytreatment.
The ZA1002US-5 controls switches, dimmers, motion sensors, temperature sensors and so
on many Z-Wave devices. ZA1002US-5integrates complicated control, automation and
internet protocols into one simple plug-and-play device. It provides an interface that allows
you to manage your home easily, whether you are at home or not.
1.1Key Features
Provide one LAN port Router function
Provide one USB 2.0 Host port, you can connect ZigbeeUSB Dongle or USB Hard Disk
ProvideWiFiIEEE 802.11b/g/n
ProvidecompatibleZ-Wave Pluscommunication protocolthat connects allkinds of
Z-Wavedevices that includeswindow sensors, electric locks, lighting dimmer controls,
energy usage monitor, air qualitydetector, temperature and humidity sensors,
firesafetysensors.
Provide a service platform to connect to the cloudservice.
ProvideIP-Camviewinginterface
ProvidefreedownloadAPP.
1.2Technical Specifications
Technical Specifications
HardwareSpecifications
USB Port USB Host 2.0 x1
Ethernet port RJ-45 10/100Mb , support 1 LAN
Physical and Environmental Characteristics
Dimensions 137(W) x 101(H) x 30(D) mm
Weight 300g
Operating Temp. Temp: 0°C~45°C (32°F~113°F)
5
& Humidity Humidity: 10%~90% relative humidity, non-condensing
Power Adaptor INPUT: AC100V~240V, 50/60Hz
OUTPUT: DC 5V, 2.0A
outer casing Plastic
Country of origin Made in Taiwan
SoftwareSpecifications
Protocol Z-Wave
WiFi IEEE 802.11b/g/n
HA Functions Sense Control
Lighting Control
Door Lock Control
Sensor Trigger Even
Schedule setting
Support mobile phone Push Notification
Support Devices Place Location
User account Management (admin and normal user)
Support Remote update software
Z-Wave Capacity Support 30 Z-Wave notes
1.3 Hardware Overview
1.3.1 Front Panel
6
1.3.2 Back Panel
DC 5V/2A:Connecting to AC adapter.Input AC 100V~240V, 50/60Hz;
Output DC 5V 2.0A
LAN: RJ-45 socket, complied with Ethernet 10/100base-T.
USB:USB 2.0 ports, USB Type A
.
Connect to power supply
For Z-Wave
USB port
LAN port
7
Chapter 2 Quick Install
After you’ve created your Z-Wave network, you’ll need to install your ZA1002US-5. Follow
these steps:
2.1 Unpacking
Open the carton and unpack the items. Your package should include:
ZA1002US-5main unit x 1 pcs
If items are missing or damaged, notify your Avadesignrepresentative. Keep the carton
and packing material.
2.2 The Procedure of Connection
Step 1: Plug in DC power adapter to ZA1002US-5.
Step 2: Connect the Ethernet cable to your ZA1002US-5LAN port.
Step 3: Plug in AC power cord to power source.
Step 4:ZA1002US-5 begins the boot process automatically.
ZA1002US-5 provides three kinds of operational platforms, Web page, Android and iOS, for
users. Therefore user can configure the ZA1002US-5 by his/her PC or smart phone or tablet.
The web configuration guide is available in this manual. The installation guide for
smartphone/tablet with Android system or iOS system, please refer to other document.
Ethernet cable
LAN port
8
2.3Find the IP address of your ZA1002US-5
Please download the Java program file named avaControlFinderJava from the website of
Avadesign Co., Ltd. http://www.avadesign.com.tw/support/support.htmlto your PC.
Decompress the file and click it twice by left button of your mouse. Then you will see the
IP address listing of all of your ZA1002US-5 as below.
avaControl Finder
2.4 Setup Wi-Fi for your ZA1002US-5(optional)
If you want to use Wi-Fi, please following the setup procedure described as below.
Step 1: At first, connect Ethernet cable to LAN port of ZA1002US-5.
Step 2: Type the IP address which getting from avaControl Finder as Sec. 2.3. For example:
type 192.168.1.8 of the ZA1002US-5in the address bar and press Enter. The screen is
shown as follows.
The username is root.Please input password: 1234 then click “Login” button on the
screen. After login ZA1002US-5, you will see the login page as shown below.
Step 2-1: Please key in 192.168.1.8 of your AVA-88.
Step 2-2: Please input password. The default
password is 1234.
Step 2-3: Click on “Login” button.
9
Step 3: Click on Network function in the top menu to setup your Wi-Fi network. The detailed
is described at Sec. 2.4.2.
Step 4: When Wi-Fi network configure has finished, please take off the Ethernet cable from
LAN port of ZA1002US-5.
Login page
After Login user will see the screen as above, and there are four maincategories in the top
menu, user can click on each category to extend detail items.
System
Network
Zwave
Logout
The various configuration menus are explained below. You can select various function listed
in the first line of web page display.
2.4.1 System
You can backup or flash firmware in this function. This function also providesreboot the
system for you.
Backup / Restore
You can click on "Generate archive" button on the screen to download a tar archive of the
current configuration files.
To restore configuration files, you also can upload a previously generated backup archive
here.
Flash new firmware image
You can upload a sysupgrade-compatible image here to replace the running firmware.
Indice
Altri manuali Vision Router di rete
Manuali Router di rete popolari di altre marche
NETGEAR
NETGEAR FS526T - Switch Manuale utente
Korenix
Korenix JetNet 5710G Series Manuale utente
Automated Logic
Automated Logic ZN551 Manuale del proprietario
Cisco
Cisco ASR 1000 Series Manuale dell'operatore
EnGenius
EnGenius ESR-9710 Manuale utente
Cisco
Cisco 805 Series Istruzioni operative e di sicurezza