VISIONARY DESIGNS MOD-1539 Manuale
© 2018
Order #XXXXX
SETUP INSTRUCTIONS
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
MOD-1539 Large Monitor Kiosk
Completed Assembly
Item
1
2
3
4
Qty.
1
1
1
1
Description
Base Plate
34”h Q914 Vertical Extrusion
34”h Q914 Vertical Extrusion
8”w Z45 Horizontal Extrusion
Steps:
1) Connect verticals [2] & [3] together. See Extrusion Connector detail.
2) Attach base plate [1] to assembled verticals.
3) Connect Monitor Mount to assembled verticals.
See Monitor Mount Attachment detail.
4) Connect Shelf [4] to assembled verticals. See Shelf Attachment detail.
5) Route cord thru Conduit. See Cord Management detail.
1
2
3
*
4
*
*
Set Screws
Connector
Extrusion Connector
Slide upper extrusion
over connector and
rest on lower extrusion.
Secure with set screws.
*
To prevent product loss,
keep all screws attached
to connector, after
disassembling.
Shelf Attachment
Insert Lock into groove of vertical
extrusion, then tighten set screw.
Lock
Set Screw
Back of Shelf
*
Cord Management
Route cord through conduit.
Attach conduit by pinching
the opening and inserting
into the groove of extrusion.
pinch
Cord
Conduit
Monitor Mount
Attachment
Slide connectors into groove of
extrusion. Tighten set screws
to secure. Attach back plate to
connectors, using bolts. Attach
monitor mount to back plate,
using bolts.
Monitor
Mount
Back
Plate
Connector
*
© 2018
Order #XXXXX General Instructions
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all setscrews
and locks during disassembly
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
© 2018
Case 1 of 1
Order #XXXXX Case Packing
2
1
4
3
Monitor
Mount
Base Plate
Setup Hardware
Top View of Each Level
Level 1 Level 2
Back Plate
Conduit
Altri manuali VISIONARY DESIGNS Segnaletica digitale
VISIONARY DESIGNS
VISIONARY DESIGNS MOD-1335 Manuale
VISIONARY DESIGNS
VISIONARY DESIGNS MOD-1370 Manuale
VISIONARY DESIGNS
VISIONARY DESIGNS MOD-1338 Manuale utente
VISIONARY DESIGNS
VISIONARY DESIGNS MOD-1336M Manuale
VISIONARY DESIGNS
VISIONARY DESIGNS MOD-1336 Manuale
VISIONARY DESIGNS
VISIONARY DESIGNS MOD-1368M Manuale
VISIONARY DESIGNS
VISIONARY DESIGNS MOD-1371M Manuale utente
VISIONARY DESIGNS
VISIONARY DESIGNS MOD-1357 Manuale
VISIONARY DESIGNS
VISIONARY DESIGNS MOD-1329 Manuale
