Visonic Networks AXS-10 PRO Manuale utente

DE6271U 1

AXS

AXSAXS

AXS-10

-10-10

-10 PRO

PROPRO

PRO

Single-Door Proximity Access Control System User Guide

1. INTRODUCTION

. INTRODUCTION. INTRODUCTION

. INTRODUCTION

The Visonic Networks AXS-10 PRO is an electronic access

control system designed for a single access point, such as a main

door in an apartment building or individual office doors. The

system control unit relay activates a lock or electromagnetic strike

lock (EMS), when a valid proximity key (tag or card) is presented

to the reader located outside the protected area.

The use of a proximity (non-contact) key makes the installation of

the AXS-10 PRO system an attractive possibility in harsh

environments and in places with poor lighting conditions. The

proximity keys are totally sealed and are wear resistant. The

reader reads the key’s ID, whenever the key is presented.

A second proximity reader may be connected to the AXS-10 PRO

to control both sides of a door. An optional magnetic stripe card

reader may be connected instead of a proximity reader.

The separate weatherproof readers give added security and

flexibility allowing outdoor or indoor installation.

The AXS-10 PRO control unit (see figure 1) includes a 3-digit

display, 3 visual indicators (LEDs) and 4 buttons. An internal

proximity reader located in the upper right corner of the control

panel allows fast and easy programming of access keys. The

buttons are used for entering the password and for programming

the unit.

Figure 1 - System Functional Presentation

RDR-3

Proximity

Reader

CRD-1

Prox. Card

TAG-1

Prox. Tag

AXS-10 PRO

Control Unit

Figure 2 - System Components

A new Toggle mode feature is added to the AXS-10 PRO

controller. By using this feature, presenting a valid tag

arms/disarms an alarm system or activate/deactivate an electrical

device (such as air conditioner).

The AXS-10 PRO has a memory capacity of 300 keys. Adding

keys simply involves presenting new keys to the controller while

the system is in ADD mode.

The user can delete keys in the DELETE mode by presenting

them to the reader or, if a tag/card is not available, by typing in its

number (the same one that appears when adding the key).

The AXS-10 PRO kit includes:

• AXS-10 PRO controller

• RDR-3 proximity reader with 1m (3 ft) 5-wire cable

• Installation instructions

• User Guide

• Control unit base template, for wall installation

Additional tools and equipment that may be needed:

• Proximity tags or cards (ordered separately)

• Power supply for the controller - 12V AC/DC

• Electromagnetic strike (EMS) unit

• Request-to-exit push button or PIR, if “request to exit” option is

required.

2. USER PROGRAMMING

. USER PROGRAMMING. USER PROGRAMMING

. USER PROGRAMMING

Note: While in any one of the programming modes, the AXS-10

PRO will not operate the reader or the lock.

2.1 Entering the Programming Menu

The master key enables the user to select the programming

menu and add or delete keys.

Note: Inactivity for more than 10 seconds will cause AXS-10 PRO

to exit the programming mode and revert to normal operation.

The AXS-10 PRO recognizes one master key and one password.

The master key cannot be used as a user key and will NOT unlock

the door. To use the master key for entering the programming

menu, press the “MODE” button and then present the master key to

the internal reader, located at the top right corner or the AXS-10

PRO controller, for 2 seconds. The reason for the 2 seconds delay

is to prevent inadvertent activation of the programming menu.

For setup functions such as “password”, “master key”, “unlock

time” or “erase all keys” an additional four-presses password is

needed. Each button press may involve pressing any one of the

four buttons or a combination of two.

Altogether, there are 10,000 password combinations (see “2.9

Setting the User Password”). The master key is also used to

confirm changes made to parameters.

2.2 Selecting the Programming Mode

The AXS-10 PRO recognizes 6 programming modes:

• Adding User Keys

• Deleting User Keys

• Erasing All User Keys

• Setting Unlock Duration

• Defining Master Key

• Setting User Password

To select the programming mode, press the “MODE” button and

present the master key to the reader until the green led (“ADD”

light) starts flashing for at least 2 seconds.

Press the “MODE” button to choose between Add, Delete and

Special Operations.

Adding User Keys is possible when the ADD light is ON.

Deleting User Keys is possible when the DELETE light is ON.

Set-up functions are available when the SPECIAL light is ON.

For set-up functions, enter the user’s password and select the

desired option by pressing the “MODE” button.

2DE6271U

Erase All User Keys - “Er”

Set Unlock - “UL”

Set Master Key - “S0”

Set User Password - “PP”

2.3 Adding User Keys

Note: It is recommended to keep a list of key-holder names and

keys address numbers, in order to be able to delete stolen or

lost keys.

• To select the ADD mode press the “MODE” button and enter

the installer password, or present the master key to the reader

until the green “ADD” LED starts flashing, indicating that the

AXS-10 PRO is ready to add a key.

• Once you present a key to the internal reader, the key will be

added and its number will be displayed for a few seconds.

• Write down the number and the key holder’s name for future

reference.

• After a few seconds the green LED will flash indicating that the

system is ready for adding the next key.

• Add another key or wait 5 seconds for the system to time out

and revert to normal operation.

2.4 Deleting User Keys

To select the DELETE mode press the “MODE” button and enter

the installer password, or present the master key to the reader

until the “ADD” LED starts flashing, then press “MODE” again.

The red “DELETE” light will start flashing to indicate that the

system is ready to delete a key.

Deleting keys can be accomplished in two ways:

• If you have the key to be deleted, present it to the internal

reader located on the top right corner of the AXS-10 PRO

controller. The key number will be displayed for a few seconds

and then the numeric display will blank to indicate readiness for

the next operation.

• To delete a missing key, press the “100”,“10” and “1” buttons

until you reach the key number you wish to delete.

For example: To indicate the number 143, press the “100”

button once, then press the “10” button four times then press

the “1” button 3 times.

Once the number is set, present the master key or press the

“MODE” button to acknowledge the operation. Hold the master

key until the key number disappears from the numeric display

and the red LED is ON. The red LED will start blinking again to

indicate that the system is ready for deleting the next key.

Present another key to be deleted or wait 5 seconds for the

system to time out and revert to normal operation.

2.5 Erasing ALL User Keys

• To select the ERASE ALL mode press the “MODE” button and

enter the installer password, or present the master key to the

reader until the ADD light starts blinking.

• Press “MODE” twice until the yellow “SPECIAL” LED lights (if

the master key is used, type the 4 level password and verify that

the display shows “Er”).

• To make sure that this function is not easily executed, you will

have to present the master key again until the yellow and green

LEDs light. This function does NOT erase the master key.

• Wait 5 seconds for the system to time out and revert to normal

operation.

2.6 Setting the Unlock Duration

The system default unlock duration is 5 seconds The time can be

set between 1 to 99 seconds.

Note: In Toggle mode, the unlock duration is unlimited (until a

valid tag is presented).

Setting Door Unlock Period:

• Press the “MODE” button.

• Enter the installer password or present the master key. The

green “ADD” LED will start flashing (if the master key is used,

press the “MODE” button a few times until the “SPECIAL” LED

lights and the display shows “UL”).

• Press F2 (tens) and F3 (units) to set the unlock time in

seconds. For example, for 35 seconds press “10” three times

and “1” five times.

• The display will show the number of seconds.

• To save the unlock time and return to normal operation,

present the master key to the internal reader.

You may press “MODE” at any time to continue without saving

the new unlock duration.

2.7 Setting AXS-10 PRO To Toggle

Mode

To turn the AXS-10 PRO into Toggle mode:

Setting the Unlock Duration (see par. 2.6) to 100 seconds turns

the AXS-10 PRO into Toggle mode. If the unlock time setting is

less then 100 second, the AXS-10 PRO is in regular mode.

To turn the AXS-10 PRO from Toggle mode into Regular mode:

Set the unlock duration to any number other than "100", then exit

the unlock duration mode.

To turn the AXS-10 PRO into Toggle mode by using master

tag:

Note: When using the master card to switch to toggle mode,

resetting the power turns the AXS-10 PRO back to regular mode.

• While the system is in idle mode present the master tag for 5

seconds to the controller reader (internal reader).

The LED will change to green (the lock is unlocked and the

AXS-10 PRO turns into Toggle mode).

• Presenting any valid non-master key will turn the relay to lock

position.

To turn the AXS-10 PRO from Toggle mode to regular mode

by using the master key:

While the system is in idle mode, present the master tag for 5

seconds. The LED will blink red, which means that the AXS-10

PRO is in regular mode.

2.8 Setting the Master Key

Note: The AXS-10 PRO can have only one master key.

• To change the master key, press the “MODE” button and enter

the installer password, or present the master key to the reader

until the “ADD” LED starts flashing.

• Press “MODE” twice until the “SPECIAL” LED lights (if the

master key is used, type the 4 digit password and verify that the

display shows “Er”, then Press “MODE” a few times until the

display shows “S0”).

• At this stage the system will try to read a key for up to ten

seconds.

• Hold the new master key until the green and yellow LED light.

• Wait 5 seconds for the system to time out and revert to normal

operation.

2.9 Setting the User Password

A password consists of four button presses, each involves either

pressing a single button or a combination of two buttons.

Note: The MODE key by itself cannot be used as the first

step of the password.

DE6271U 3

The following table shows the possible combinations:

100 +

MODE F3

MODE F2

10 +

100

MODE F2

10 +

MODE F3

100

A sample password:

10 ,

MODE

100 ,

10 ,

10 +

To select the CHANGE PASSWORD mode:

• Press the “MODE” button and enter the installer password, or

present the master key to the reader until the “ADD” LED starts

blinking.

• Press the “MODE” button twice until the “SPECIAL” LED lights

(if the master key is used, enter the current 4 level password

and verify that the display shows “Er”, then press the “MODE”

button a few times until the display shows “PP”).

• Enter in the new password, as a combination of 4 button presses.

• Present the master key until the green and yellow LEDs light to

confirm acceptance of the password.

• Press “MODE” for the next programming modes or simply wait

5 seconds for the system to time out and revert to normal

operation.

3. NORMAL OPERATION

. NORMAL OPERATION. NORMAL OPERATION

. NORMAL OPERATION

3.1 Valid Key Detection

If a key is presented to the external reader,the AXS-10 PRO will

search the list of valid keys in its memory. If the key is found, the

AXS-10 PRO will light the green LED and activate the output

relay to unlock the door for the pre-programmed unlock duration.

3.2 Invalid Key Detection

If the key presented to the reader is not found in the AXS-10 PRO

memory, the red LED will light for two seconds and the lock will

not open.

3.3 Internal Request To Exit

The AXS-10 PRO has a request-to-exit feature. To use it connect a

proper Normally Open switch or PIR detector to the Request-to-exit

terminal in the AXS-10 PRO. Each time the button is pressed or

the PIR detects, the relay output of the AXS-10 PRO will be

activated for the pre-programmed unlock duration.

WARRANTY

WARRANTYWARRANTY

WARRANTY

Visonic Networks Ltd. and/or its subsidiaries and its affiliates ("the Manufacturer") warrants its

products hereinafter referred to as "the Product" or "Products" to be in conformance with its

own plans and specifications and to be free of defects in materials and workmanship under

normal use and service for a period of twelve months from the date of shipment by the

Manufacturer. The Manufacturer's obligations shall be limited within the warranty period, at its

option, to repair or replace the product or any part thereof. The Manufacturer shall not be

responsible for dismantling and/or reinstallation charges. To exercise the warranty the product

must be returned to the Manufacturer freight prepaid and insured.

This warranty does not apply in the following cases: improper installation, misuse,

failure to follow installation and operating instructions, alteration, abuse, accident or

tampering, and repair by anyone other than the Manufacturer.

This warranty is exclusive and expressly in lieu of all other warranties, obligations or

liabilities, whether written, oral, express or implied, including any warranty of

merchantability or fitness for a particular purpose, or otherwise. In no case shall the

Manufacturer be liable to anyone for any consequential or incidental damages for breach

of this warranty or any other warranties whatsoever, as aforesaid.

This warranty shall not be modified, varied or extended, and the Manufacturer does not

authorize any person to act on its behalf in the modification, variation or extension of this

warranty. This warranty shall apply to the Product only. All products, accessories or

attachments of others used in conjunction with the Product, including batteries, shall be

covered solely by their own warranty, if any. The Manufacturer shall not be liable for any

damage or loss whatsoever, whether directly, indirectly, incidentally, consequentially or

otherwise, caused by the malfunction of the Product due to products, accessories, or

attachments of others, including batteries, used in conjunction with the Products.

The Manufacturer does not represent that its Product may not be compromised and/or

circumvented, or that the Product will prevent any death, personal and/or bodily injury

and/or damage to property resulting from burglary, robbery, fire or otherwise, or that the

Product will in all cases provide adequate warning or protection. User understands that a

properly installed and maintained alarm may only reduce the risk of events such as

burglary, robbery, and fire without warning, but it is not insurance or a guarantee that

such will not occur or that there will be no death, personal damage and/or damage to

property as a result.

The Manufacturer shall have no liability for any death, personal and/or bodily injury

and/or damage to property or other loss whether direct, indirect, incidental,

consequential or otherwise, based on a claim that the Product failed to function.

However, if the Manufacturer is held liable, whether directly or indirectly, for any loss or

damage arising under this limited warranty or otherwise, regardless of cause or origin, the

Manufacturer's maximum liability shall not in any case exceed the purchase price of the

Product, which shall be fixed as liquidated damages and not as a penalty, and shall be

the complete and exclusive remedy against the Manufacturer.

Warning: The user should follow the installation and operation instructions and among

other things test the Product and the whole system at least once a week. For various

reasons, including, but not limited to, changes in environmental conditions, electric or

electronic disruptions and tampering, the Product may not perform as expected. The user

is advised to take all necessary precautions for his /her safety and the protection of

his/her property.

6/91

This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference in residential installations. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio and

television reception. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause such

interference, which can be verified by turning the device off and on, the user is encouraged to eliminate the interference by one or more of the

following measures:

– Re-orient or re-locate the receiving antenna.

– Increase the distance between the device and the receiver.

– Connect the device to an outlet on a circuit different from the one which supplies power to the receiver.

– Consult the dealer or an experienced radio/TV technician.

TECHNICAL DEPT.: 39 HAMELACHA ST. CARMIEL 20100 ISRAEL TEL: 972 4 9081115 FAX: 972 4 9081116

Tech. Support email: [email protected]

VISONIC INC. (U.S.A.): 10 NORTHWOOD DRIVE, BLOOMFIELD CT. 06002-1911. TEL: (860) 243-0833, (800) 223-0020 FAX: (860) 242-8094

VISACCESS LTD. (UK): UNIT 1, STRATTON PARK, DUNTON LANE, BIGGLESWADE, BEDS. SG18 8QS. TEL: (01767)600857 FAX: (01767)601098

INTERNET: www.visonicnet.com

Visonic Networks Ltd. 2002 AXS-10 PRO DE6271U (REV. 0, 5/2002)

4DE6271U

Appendix - Users List

Tag

No.

User name PIN

code

Tag

address

Tag

No.

User name PIN

code

Tag

address

1 001 51 051

2 002 52 052

3 003 53 053

4 004 54 054

5 005 55 055

6 006 56 056

7 007 57 057

8 008 58 058

9 009 59 059

10 010 60 060

11 011 61 061

12 012 62 062

13 013 63 063

14 014 64 064

15 015 65 065

16 016 66 066

17 017 67 067

18 018 68 068

19 019 69 069

20 020 70 070

21 021 71 071

22 022 72 072

23 023 73 073

24 024 74 074

25 025 75 075

26 026 76 076

27 027 77 077

28 028 78 078

29 029 79 079

30 030 80 080

31 031 81 081

32 032 82 082

33 033 83 083

34 034 84 084

35 035 85 085

36 036 86 086

37 037 87 087

38 038 88 088

39 039 89 089

40 040 90 090

41 041 91 091

42 042 92 092

43 043 93 093

44 044 94 094

45 045 95 095

46 046 96 096

47 047 97 097

48 048 98 098

49 049 99 099

50 050 100 100

Note

This is a sample user list for your convenience. Please copy the list as necessary.

Altri manuali Visonic Networks Controllori di accesso IP

Visonic Networks

Visonic Networks TAG-IN-A-BAG Guida all'installazione

Manuali Controllori di accesso IP popolari di altre marche

ZKTeco

ZKTeco SpeedFace-V5L Manuale utente

Jantar

Jantar REX A-1-9 Manuale utente

2N Access Unit Foglio di istruzioni

Kedacom

Kedacom KSCA120 Series Manuale utente

H3C

H3C WX2880X Manuale utente

G4S

G4S S870-EX Guida

PRASTEL

PRASTEL M2000PE Manuale utente

Allegion

Allegion interflex IF-281 Cylinder Manuale utente

TECOM

TECOM TS1067E Manuale utente

Fermax

Fermax Memokey 100C Guida utente

Fermax

Fermax CITYLINE MEMOKEY Manuale di istruzioni

Software House

Software House iSTAR Pro 2U RM Manuale di istruzioni

AKCP

AKCP SP+ Manuale utente

Bpt

Bpt HNA/102 Manuale utente

Civintec

Civintec CV9601T-T-1F Manuale utente

BioMax

BioMax N-X90W Manuale utente

ZKTeco

ZKTeco OP-200 Manuale utente

FingerTec

FingerTec s-Kadex Manuale utente