Vitek VTC-TNT5RFEB-2 Manuale utente

VITEK

VTC-TNT5RFE-2

Transcendent Series 5MP

Indoor/Outdoor WDR IP

Camera with Matrix IR LED

Illumination

QUICK START GUIDE

PLEASE NOTE:

Complete User Guide, Software, Tools, and Updates are

available online. Scan the QR Code or visit:

http://www.vitekcctv.com/Downloads

FEATURES

• 1/2.5” 5.0 MegaPixel CMOS Image Sensor

• Up to 20fps live view @ 5 MegaPixel (2592x1944)

• 2.8mm Fixed Iris Lens

• 1 Matrix Style Infrared LED with a 100’ IR Range

• Digital Wide Dynamic Range (D-WDR)

• True Mechanical Day/Night function by ICR

• XD-DNR (3D-DN & 2D-DNR) Noise Reduction

• H.265, H.264 & MJPEG Compression

• On Board Motion Detection, Privacy Masking, Region of Interest,

Exception, Line Crossing, Intrusion, Object Detection / Removal

(Museum Search)

• 1 Ch. Built-in Audio

• Remote Viewing via CMS, Internet Explorer, and iOS & Android

Apps

• ONVIF Compliant

• IP67 Weather Resistance

• Optional Junction Box Mounts (VT-TJB01/B, VT-TJB08/B) and

Wall Mount (VT-TWMT3/B) Available

• 12VDC / 1Amp & PoE (Power over Ethernet) Operation

• Available in Ivory or Charcoal Grey (VTC-TNT5RFEB-2)

All manuals and user guides at all-guidesbox.com

all-guidesbox.com

2 3

Network Cable &

Power Connections

First connect the Waterproof Cap to an Ethernet patch cable, then

connect the cameras ethernet adaptor. If not powering the camera

with PoE, also connect the power Cable to an approved 12VDC Power

Supply.

Overview

Components and Accessories

Camera

Quick Guide

Screws

Hex Wrench

Drill Template

Rubber Plug

Waterproof Cap

Lens

RJ-45 Ethernet

Power Input

1 Ch. Built-in MIC

12VDC

Optional 12VDC / 1Amp

Power Connection.

Not needed with PoE

Network Cable

All manuals and user guides at all-guidesbox.com

Weather Resistant Network Coupler

1. Loosen the nut from the weather resistant network coupler,

2. Run the weather rated ethernet cable through coupler, then attach

a RJ-45 connector.

3. Tighten the nut and coupler for a weather resistant seal.

Installation

Before beginning installation, make sure that the wall or ceiling is

strong enough to withstand 3 times the weight of the camera. The

mounting steps are as follows:

1. Attach the drill template to

the place where you want to

install the camera, then drill

3 screw holes and 1 cable

hole (if you want to route the

cables through the mounting

base) according to the drill

template

2. Route the cables and connect the power & video cables, use the

rubber plug to fill the gap on the mounting base. then secure the

mounting base to the ceiling or wall with screws.

All manuals and user guides at all-guidesbox.com

4 5

Installation

4. Tighten the lock screw to secure the viewing angle adjustments.

5. Carefully remove the protective film from the lens to complete the

installation.

Lock Screw

3. Loosen the lock screws,

then adjust the camera

to obtain the optimium

viewing angle. Confirm

the correct viewing

angle with a monitor.

(See next page for

location of lock screw)

Rubber Plug

All manuals and user guides at all-guidesbox.com

LAN Configuration

The camera can be accessed on the local network either using the

IP-Tool or directly in a web browser.

Accessing the Camera Using the IP-Tool

1. Make sure the camera and PC are connected to the LAN.

2. Locate the IP-Tool installer at https://vitekcctv.com/search-down-

loads/, then install on the PC. Open the installed application.

3. Modify the IP address. The default IP address is 192.168.226.201.

Click the information of the camera listed in the above table to show

the network information on the right side. Modify the IP address and

gateway of the camera and make sure its network address is in the

same local network segment as the computer’s. Please modify the

IP address of your device according to the practical situation.

For example, the IP address of your computer

is 192.168.13.4. So the IP address of the

camera shall be changed to 192.168.13.X.

After modification, please input the password

of the administrator and click “Modify” button

to modify the setting.

** Default admin password: “123456".

IPC

Network Cable Network Cable

Switch

Router Computer

All manuals and user guides at all-guidesbox.com

6 7

4. Double-click the IP address and then the system will pop up the

web browser to connect IP-CAM . IE browser will download the

Active X control. After downloading, a login window will pop up

as shown below:

Input the user name and password to log in.

Default user name: admin / Default password: 123456.

Directly Access Through a Web Browser

The default network settings are as shown below:

IP address: 192.168.226.201 HTTP: 80

Subnet Mask: 255.255.255.0 Data Port: 9008

Gateway: 192.168.226.1

You may use the above default settings when you log in the camera

for the first time.

1. Manually set the IP address of the PC. The network segment

should be the same as the default settings of IP-CAM. Open the

network and share center. Click “Local Area Connection” to pop up

the following window.

Select “Properties” and then select Internet protocol according to the

actual situation (for example: IPV4). Next, click “Properties” button to

set the network of the PC.

All manuals and user guides at all-guidesbox.com

all-guidesbox.com

2. Open the IE Browser and input the default address of IP-CAM and

confirm. The IE browser will download Active X control.

3. After downloading Active X control, the login dialog box will pop up.

4. Input the default username and password and then enter to view.

WAN Configuration

Access the camera by the router or virtual server for example.

1. Make sure the camera is connected to the LAN; Then log into the

camera via LAN and go to System Congfig→Network Config→Port

menu to set up the port number.

2. Enter System Config→Network Config→IP Address menu to

modify the IP address.

4. Open the web browser and input its WAN IP and HTTP port to

access the IP-CAM.

3. Go to the router’s management interface through IE browser to

forward the IP address and port of IP-CAM in the “Virtual Server”.

All manuals and user guides at all-guidesbox.com

28492 CONSTELLATION ROAD VALENCIA, CA 91355

WWW.VITEKCCTV.COM

Version 3.0

Sept 2019

LIMITED PRODUCT WARRANTY

VITEK products carry a three (3) year limited warranty. VITEK warrants

to the purchaser that products manufactured by VITEK are free of any

rightful claim of infringement or the like, and when used in the manner

intended, will be free of defects in materials and workmanship for a

period of three (3) years, or as otherwise stated above, from the date of

purchase by the end user. This warranty is nontransferable and extends

only to the original buyer or end user customer of a VITEK Authorized

Reseller.

The product must have been used only for its intended purpose, and

not been subjected to damage by misuse, willful or accidental damage,

caused by excessive voltage or lightning.

The product must not have been tampered with in any way or the

guarantee will be considered null and void.

This guarantee does not affect your statutory rights.

Contact your local VITEK Reseller should servicing become necessary.

VITEK makes no warranty or guarantee whatsoever with respect to

products sold or purchased through unauthorized sales channels.

Warranty support is available only if product is purchased through a

VITEK Authorized Reseller.

All manuals and user guides at all-guidesbox.com

Indice

Altri manuali Vitek Telecamera di sicurezza

Vitek

Vitek VTC-IRLED30A Manuale utente

Vitek

Vitek Transcendent VTC-TNB5RMS Manuale utente

Vitek

Vitek Transcendent Series Manuale utente

Vitek

Vitek VTC-IRH70 Manuale utente

Vitek

Vitek VTD-VH49B2 Manuale utente

Vitek

Vitek TRANSCENDENT VTC-THT10R2F Manuale utente

Vitek

Vitek Transcendent VTC-TNT8RFS Manuale utente

Vitek

Vitek Transcendent VTC-TNB8RMA4 Manuale utente

Vitek

Vitek VTD-TND8RFA4-2 Manuale utente

Vitek

Vitek TRANSCENDENT VTD-T4D6HR5MD Manuale utente

Vitek

Vitek VTD-M2HET2812 Manuale utente

Vitek

Vitek VTC-C770WS Manuale utente

Vitek

Vitek Transcendent Series Manuale utente

Vitek

Vitek VTD-TND4RFA4 Manuale utente

Vitek

Vitek Transcendent VTC-THB5RM Manuale utente

Vitek

Vitek VT-PTZ220HD Manuale utente

Vitek

Vitek TRANSCENDENT VT-TPTZ4AD-4M Manuale utente

Vitek

Vitek VT-PTZ40WH Manuale utente

Vitek

Vitek VTD-AR2D4FN Manuale utente

Vitek

Vitek Transcendent Series Manuale utente

Vitek

Vitek VTC-IRE24F Manuale utente

Vitek

Vitek VTC-IRLED30 Manuale utente

Vitek

Vitek VTC-IRE40 Manuale utente

Vitek

Vitek VTD-M30 Manuale utente

Manuali Telecamera di sicurezza popolari di altre marche

Okina USA

Okina USA SIR36-870VF650LP Manuale utente

Divio

Divio NDR155PA Manuale utente

Canon

Canon VB-C500D Manuale utente

Easy Access

Easy Access EasyGuard Manuale utente

Vivotek

Vivotek FD9389-EHV-v2 Manuale utente

TUYA

TUYA COSMO W2 Manuale utente

Eusso

Eusso UNC7500-IR Guida all'installazione

urmet domus

urmet domus 1096/204 Manuale utente

VC VC20 series Manuale utente

Axis

Axis Q1614 Manuale utente

ieGeek

ieGeek DD201 Manuale utente

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuale utente

Vicon

Vicon V662-D-1 Istruzioni operative

Grundig

Grundig GCH-K0274P Manuale utente

Lorex

Lorex VANTAGE LBC7032 Manuale utente

4xem

4xem WPT Manuale utente

Samsung

Samsung SCV-3082 Manuale utente

Lumens

Lumens VC-A50PNW Manuale utente