Vitek VTD-THD5R3 Manuale utente

VITEK

VTC-THT5R3/R2

VTD-THD5R3/R2

VTC-THB5R3/R2

Transcendent 5.0 Megapixel Indoor/Outdoor

4-in-1 Fixed Lens Cameras

FEATURES

• 1/2.7” 5.0 MegaPixel Progressive Scan CMOS Image Sensor

• High Definition Analog (HDA): HD-TVI / AHD: 5.0MP

/ HD-CVI: 4.0MP / CVBS: 960H Video Output

• 3.6 or 2.8mm Fixed Iris Lens Options

• Supports OSD Menu

• Matrix IR with up to 165’ IR Range (VTC-THB5R3/R2)

• Matrix IR with up to 100’ IR Range (VTC-THT5R3/R2)

• 16 IR LEDs with up to 65’ IR Range (VTD-THD5R3/R2)

• True Mechanical Day/Night function by ICR

• Digital Wide Dynamic Range (D-WDR)

• XD-DNR Noise Reduction

• IP67 Weather Resistance (+IK10 on VTD-THD5R3/R2)

• Supports Control over COAX (CoC)

• Over 1500’ HD Video Transmission (Depending on cable

characteristics and integrity)

• VTC-THB5R3/R2: J Box - TJB08

VTC-THT5R3/R2: J Boxes - VT-TJB01, TJB08, Wall Mount VT-TWMT-3

VTD-THD5R3/R2: J Box - VT-TJB03A, Wall Mount VT-TWMT-3,

In-ceiling Semi Flush Mount VT-TFMT-S

*Corner and pole adapters also available - see rear page

• VTC-THT5R3/R2 also Available in Charcoal (VTC-THT5R3B/2B)

• 12VDC Operation

• 3-year Warranty

All manuals and user guides at all-guides.com

Safety Precaution

CAUTION: TO REDUCE THE RISK OF ELECTICAL

SHOCK, DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

To prevent electrical shock and risk of fire hazards, do not expose this unit

to rain or moisture and only use specified power source..

Warning :

This equipment has been tested and found to comply with the limits for a Class

A digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference when the equipment

is operated in a commercial environment. This equipment generates, uses, and

can radiate radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at

their own expense.

Caution :

Any changes or modifications in construction of this device which are not expressly

approved by the party responsible for compliance could void the user's authority

to operate the equipment.

Main power quality should be that of atypical commercial environment. If the user

of the model requires continued operation during power interruptions, it is

recommended that the device be powered from an uninterruptible power supply

(UPS).

The symbol is intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in the literature

accompanying the unit.

The symbol is intended to alert the user tothe presence of uninsulated

"dangerous voltage" within the product's enclosure that may be of

sufficient magnitude toconstitute a risk of electrical shock.

All manuals and user guides at all-guides.com

VTC-THB5R3/R2 - Components

Overview

Lens

Sun Shield

Mount Lock

Mount Base

BNC Video Output

Output Mode Switch

Power Cable

Video Connection

Connect the BNC video connector to a BNC cable, then to a DVR.

Power

12VDC

Power Connection

Connect the power connector to a regulated 12 VDC power adaptor.

Monitor

Video

Camera

Manual

Drill Template

Screws

Allen Key

This series supports TVI/AHD/CVI/CVBS video output. Before switching

video outputs, please remove the cover of the video switch cable.

The video output can be changed by pressing and holding the button in

the video switch cable for 5 seconds.

Video Output Mode Switch:

Video Switch Cable

All manuals and user guides at all-guides.com

Installation

Before beginning installation, make

sure that the wall or ceiling is strong

enough to withstand 3 times the weight

of the camera. The mounting steps are:

2. Route the cables and connect the power & video cables, use the

rubber plug to fill the gap of the mounting base, then secure the

mounting base to the ceiling or wall with screws.

Rubber plug

3. Loosen the mount lock to adjust the pan and tilt, then tighten the

mount lock to secure the viewing angle adjustments.

4. Carefully remove the protective film from the lens to complete the

installation.

90° T ILT

360° ROTATION

360° PAN

FIXED RING

1. Attach the drill template to

the place where you want to

install the camera, then drill

3 screw holes and 1 cable

hole (if routing the cables

through the mounting base)

according to the drill

template

All manuals and user guides at all-guides.com

VTC-THT5R3/R2 Components

Overview

Camera

Manual

Screws

Allen Keyt

Mounting Plate

Rubber Plug

Lens

Lock Screws

BNC Video Output

Output Mode Switch

Power Cable

Monitor

Video

Video Connection

Connect the BNC video connector to a BNC cable, then to a DVR.

Power Connection

Connect the power connector to a regulated 12 VDC power adaptor.

Power

12VDC

This series supports TVI/AHD/CVI/CVBS video output. Before switching

video outputs, please remove the cover of the video switch cable.

The video output can be changed by pressing and holding the button in

the video switch cable for 5 seconds.

Video Output Mode Switch:

Video Switch Cable

All manuals and user guides at all-guides.com

Installation

Before you begin, please make sure that the wall or ceiling is strong

enough to withstand 3 times the weight of the camera. The mounting

steps are as follows:

1. Attach the drill template to

the place where you want to

install the camera, then drill

3 screw holes and 1 cable

hole (if you want to route the

cables through the mounting

base) according to the drill

template

2. Route the cables and

connect the power & video

cables, then secure the

mounting base to the ceiling

or wall with screws.

3. Loosen the lock screws, then

adjust the camera to obtain

the optimium viewing angle.

Confirm the correct viewing

angle with a monitor. Next

insert the rubber plug.

4. Tighten the lock screws to secure the viewing angle adjustments.

Rubber Plug

All manuals and user guides at all-guides.com

VTD-THD5R2/R3 Components

Overview

Camera

Manual

Drill Template

Screws

Allen Key

Mounting Base

Dome Cover Output Mode Switch

Power Cable

Monitor

Video

Video Connection

Connect the BNC video connector to a BNC cable, then to a DVR.

Power Connection

Connect the power connector to a regulated 12 VDC power adaptor.

Power

12VDC

BNC Video Output

Trim Ring

This series supports TVI/AHD/CVI/CVBS video output. Before switching

video outputs, please remove the cover of the video switch cable.

The video output can be changed by pressing and holding the button in

the video switch cable for 5 seconds.

Video Output Mode Switch:

Video Switch Cable

All manuals and user guides at all-guides.com

Installation

Before beginning installation, make sure that the wall or ceiling is

strong enough to withstand 3 times the weight of the camera. The

mounting steps are as follows:

Loosen the screws to open

the lower dome and then

loosen the lock screw to

remove the mounting base.

1. Attach the drill template to

the place where you want to

install the camera, then drill

the screw holes and 1 cable

hole according to the drill

template.

3. Route the cables and

connect the power & video

cables, use the rubber plug

to fill the gap of the mounting

base. then secure the

mounting base to the ceiling

or wall with screws.

2. *Unscrew the trim ring by turning it

counter-clockwise. This will enable the

removal of the lower dome.

4. Adjust the Three-axis camera bracket to obtain the optimium

viewing angle.

5. Install the dome bubble on

the camera with the screws,

then replace the trim ring

by turning it clockwise.

Finally, carefully remove the

protective film to complete the

installation.

Pan: 0°~240°

Rotation: 0°~220°

Tilt: 0°~68°

All manuals and user guides at all-guides.com

Camera OSD Menu

The Transcendent 4-in1 camera series must be connected to a DVR

which supports HD-TVI/AHD video signal input and COC protocol to

access the OSD setup menu. Different DVRs manufacturers may have

different modes of menu operation.

You can select the menu by clicking (U) or (D) key on the

direction area. Click (L) or (R) key to select the menu on the

left. The menu with arrow icon which means it has sub-menu. You

can select the menu and click the Enter Button to enter the

sub-menu. to return to previous screen, arrow down to Return and

click Enter Button. To Exit menu arrow down to Exit and click Enter

Button.

You will see the following interface by clicking the PTZ button.

The Following image will pop-up when you left click once on the

image when using Transcendent HDA DVR's.

Click on the OSD tab and then click on the camera menu

button.

All manuals and user guides at all-guides.com

Detailed Specifications VTC-THT5R3(B)/R2(B) VTC-THB5R3/R2

Image Sensor

Signal System

Effective Pixels

Resolution

Video Output

Lens

Day/Night

Min. IIIumination

IR LEDs

IR Distance

S/N Ratio

WDR

Digital Noise Reduction (DNR)

White Balance

BLC, LSC, HLC

Control over COAX (COC)

Transmission Distance

Power Input

Power Consumption (12VDC)

Resistance Rating

Operation Conditions

Weight

Dimensions

1/2.7” 5.0 Megapixel Progressive Scan CMOS Sensor

PAL / NTSC

2560 x 1936

HD-TVI & AHD: 5.0 MegaPixel / CVI: 4.0 MegaPixel / CVBS: 960H

HD-TVI / AHD / CVI / CVBS (Selectable)

3.6 or 2.8mm - Fixed

True Day/Night by ICR

Up to 165’

≥52dB (AGC Off)

Digital Noise Reduction

Auto (AWB)

YES

Up to 1500’ (Depending on cable characteristics & integrity)

12VDC

IP67

-4°~122° / 10%~90% Humidity

8.68 × 3.15 × 2.78” (220.5 × 80.1 × 70.5mm)

2 Matrix

3.77” × 4.25” (95.7 × 108mm)

Digital WDR

AGC, Mirror, Sharpness, Smart IR, Image Setting, Defect Correction

VTD-THD5R3/R2

4.69” x 3.47” (119mm × 88mm) Dia x H

(+IK10)

IR Off: 100mA / IR On: 500mA

21.87 oz. / 1.37 lbs. / 620g

14.81 oz. / .93 lbs. / 420g 20.81 oz. / 1.30 lbs. / 590g

Color: 0.01 [email protected], AGC ON / B/W: 0 lux (with IR ON)

16 IR LEDs

1 Matrix

Up to 65’

Up to 100’

IR Off: 100mA / IR On: 350mAIR Off: 100mA / IR On: 350mA

Other Features

All manuals and user guides at all-guides.com

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Vitek Telecamera di sicurezza

Vitek

Vitek Transcendent VTC-TNB8RFS-2 Manuale utente

Vitek

Vitek Alpha VTD-A2812/I Manuale utente

Vitek

Vitek Alpha VTD-C14A Manuale utente

Vitek

Vitek Mighty VTD-MP2810WDR Manuale utente

Vitek

Vitek VTC-C770WS Manuale utente

Vitek

Vitek VTD-VS48B2 Manuale utente

Vitek

Vitek VTC-IRE40 Manuale utente

Vitek

Vitek VTD-VS48 Manuale utente

Vitek

Vitek VTC-IRE40 Manuale utente

Vitek

Vitek Mighty VTD-MP1850DN Manuale utente

Vitek

Vitek VTC-EB15B Manuale utente

Vitek

Vitek VTC-TNT30R3F Manuale utente

Vitek

Vitek VTC-BHOCR4F Manuale utente

Vitek

Vitek VTD-VPH266 Manuale utente

Vitek

Vitek Transcendent VTD-TND24R5F2 Manuale utente

Vitek

Vitek VT-PTZ36W Manuale

Vitek

Vitek VTC-IRM5H-2713 Manuale utente

Vitek

Vitek VTC-TTAB42R2F Manuale utente

Vitek

Vitek VTC-C750/DN Manuale utente

Vitek

Vitek VTC-BHOCR2812 Manuale utente

Vitek

Vitek VTC-IRH650 Manuale utente

Vitek

Vitek VT-PTZ12WH Manuale utente

Vitek

Vitek VTC-THT5R3 Manuale utente

Vitek

Vitek VTC-IRA70/650 Manuale utente

Manuali Telecamera di sicurezza popolari di altre marche

Okina USA

Okina USA SIR36-870VF650LP Manuale utente

Divio

Divio NDR155PA Manuale utente

Canon

Canon VB-C500D Manuale utente

Easy Access

Easy Access EasyGuard Manuale utente

Vivotek

Vivotek FD9389-EHV-v2 Manuale utente

TUYA

TUYA COSMO W2 Manuale utente

Eusso

Eusso UNC7500-IR Guida all'installazione

urmet domus

urmet domus 1096/204 Manuale utente

VC VC20 series Manuale utente

Axis

Axis Q1614 Manuale utente

ieGeek

ieGeek DD201 Manuale utente

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuale utente

Vicon

Vicon V662-D-1 Istruzioni operative

Grundig

Grundig GCH-K0274P Manuale utente

Lorex

Lorex VANTAGE LBC7032 Manuale utente

4xem

4xem WPT Manuale utente

Samsung

Samsung SCV-3082 Manuale utente

Lumens

Lumens VC-A50PNW Manuale utente