3
Switch off the mains power supply and remove the plug by hand.
Always disconnect the appliance from the power supply before assembling,
disassembling or performing cleaning or maintenance.
Do not immerse the Espresso Coffee Maker, power supply cord or plug in water.
Care should be taken to avoid spillage on the electrical components, power cord
and plug.
Do not use any accessories or attachments with the appliance that have not been
supplied or recommended by the manufacturer.
Caution: Misuse of the appliance could cause injury – do not use the appliance
for anything other than its intended use.
Caution: Hot surface. To avoid injury do not touch the hot or heated
surfaces of the Espresso Coffee Maker including the Cup Warming Plate. The
heated surfaces and heating element may contain residual heat and still be hot
after use. Allow the Espresso Coffee Maker to cool fully before moving or handling.
Boiling Water and Steam are released from the Espresso Coffee Maker during use
and can cause serious injury, scalds and burns. Exercise caution when using the
steam function and allow the brewing cycle to finish before removing the mugor
adjusting the Function Selector Knob.
Do not open the water tank cover or remove the mug while a brewing cycle is in
progress. Wait for the brewing cycle to finish before refilling.
Do not overfill the Espresso Coffee Maker or mug with water as hot water could
overflow during the brewing cycle
CLEANING AND MAINTAINENCE
Unplug the product from the mains power supply and allow to cool fully before
performing any cleaning or maintenance.
Dispose of the used coffee grounds in
the Portafilter (recycle if possible) and
remove the metal filter by pulling it from
the Portafilter handle. Wash out any
remaining coffee grounds with cool,
clean water.
Lift the Drip tray and grille out from the coffee machine and rinse the Drip tray,
grille, metal filer and Portafilter handle in hot soapy water.
Remove the Water tank by pulling it gently up and away from the machine and
rinse with cool, clean water.
4
Gently pull the metal Steam Wand cover away from the grip to
remove and wipe with a soft, damp cloth and a small amount
of mild detergent. Use the cleaning wire to ensure the steam
outlet and hole in the cover are free from obstruction.
Wipe the coffee machine body and all other accessories with a soft, damp cloth.
Leave all pieces to dry naturally before reassembly. Do not use strong detergent,
sharp objects, brushes or other objects to clean the coffee machine body and
accessories as this could cause damage to the finish. Do not immerse the main
unit in water. All parts are not dishwasher safe.
DESCALING THE ESPRESSO COFFEE MAKER
To maintain the performance and correct operation of your Espresso Coffee Maker
it should be descaled regularly. Mineral deposits from the water will form on the
inside of the coffee maker, especially in hard water areas.
To descale the Espresso Coffee Maker use a
commercially available descaling solution
which is suitable for use with coffee makers.
Add the descaling agent to a full water tank
and place a suitably sized cup onto the grille.
Press and hold the Single Cup Function Button
then plug in and switch on the coffee maker at
the mains power supply to enter descaling
mode. The coffee maker will emit two beeps
and the Single Cup Function Button will light up.
Press the Single Cup Function Button to begin descaling the coffee machine. Press
the Single Cup Function Button again to stop descaling the coffee machine. The
Coffee Machine will run for up to 120 seconds unless stopped manually.
When descaling is complete dispose of any remaining water in the water tank and
rinse thoroughly. Refill with cool, clean water and run the coffee machine through
another descaling cycle without the descaling solution to flush out the system
before use. Press the power button to exit descaling mode.
STORAGE
Before storing, ensure that the Espresso Coffee Maker is cool, clean and dry.
Reassemble all of the parts and wrap the power cord loosely around the body of
the Espresso Coffee Maker. Never wrap the cord tightly to avoid causing damage.
Store in a cool, dry place away from direct sunlight.
