Vivax OSK105 Manuale utente
ENG VIVAX
1
VIVAX ENG
2
Please read this owner s manual carefully and thoroughly before operating the unit!
Take care of this manual for future reference!
CONTENTS
Specification 3
Precaution 3
Technical solution 3
Operational instruction 4
How to use App 13
Special functions 14
Waste disposal, CE Declaration of Conformity 18
CAUTIONS
Only operate the device in accordance with the instructions
supplied. This device complies with FCC and IC radiation
exposure limits set forth for an uncontrolled environment. In
order to avoid the possibility of exceeding the FCC and IC radio
frequency exposure limits, human proximity to the antenna shall
not be less than 20cm (8 inches) during normal operation.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate the equipment.
Company will not be liable for any issues and problems caused
by Internet, Wi-Fi Router and Smart Devices. Please contact the
original provider to get further help.
ENG VIVAX
3
Specifications
Model: OSK105
Standard: IEEE 802.11b/g/n
Antenna Type: Printed PCB Antenna
Frequency: 2400-2483.5 MHz
Maximum Transmitted Power: <20dBm Max
Dimension: 55*24*8(mm)
Operation Temperature: 0 C~45 C/32 F~113 F.
Operation Humidity: 10%~85%
Power Input:DC 5V/300mA
Precautions
Applicable system :IOS, Android. (Suggest:IOS 7.0 or later Android 4.0 or later)
Please check the service website for more applicable devices.
Disclaimer:Due to the special situation existed during App use,we explicitly claim as bellow:
Not all of the Android and IOS systems are compatible with the APP.We will not be responsible
for any issue as a result of the incompatibility
SMART KIT wireless safety strategy.
Smart kit Only support WPA-PSK/WPA2-PSK encryption and none encryption .
WPA-PSK/WPA2-PSK encryption is recommended
Smart Phone camera needs to be 5 million pixels or above to make sure scan QR code well.
Due to different network situation, sometimes, request time-out could be happened, thus, it is
necessary to do network configuration again.
Due to different network sitiuation, sometimes, control process may return time out. If this
situation occurs, do not feel confused, the display on board and APP may not be the same.
Technical solution
WIFI Router Home Control Mode.
A WIFI router is needed at this
mode. Smart phone and connect to
the AC through the WIFI router
conditioner.
1 Smart Phone
2 Smart Air conditioner
3 WIFI Router
VIVAX ENG
4
Install the Wi-Fi Smart kit
1. Remove the protective cap of the smart kit
2. Open the front panel and insert the smart kit
into the reserved port
3. Attach the QR code packed with SMART KIT to the side panel of the
machine, ensure it is convenience to be scanned by the mobile phone.
Operation Instructions
1. Install App
1). Iphone Users: Scan QR Code or go to App Store and search for NetHome Plus app
and download it.
2). Android Phone users: Scan QR Code or go to Google play, search for NetHome Plus
app and download it
2. Set Air conditioner to be AP mode
The procedure includes the following steps:
1) Disconnect the power supply of AC
2) Connect the power supply of AC, and continuously press the digital display button or
do not disturb button seven times in 3 minutes.
3) When the AC displays AP, it means that the AC WIFI has already entered into the WIFI
Network Setting Mode.
Note:
When the AC WI-FI entered into WI-FI Network Setting Mode, the Air-conditioning remote
control can't open the AC. It needs to wait 3-5 minutes or when the AC finishes the WIFI Network
Setting Mode, then the Air-conditioning remote control can control AC normally.
If there is no set operation under WIFI Network setting mode,AC will quit this mode
automatically 8 minutes later ,and then the user can control the AC normally.
ENG VIVAX
5
3. User Registration
Please ensure your mobile device is connected to Wifi router. Also, the Wifi router has
already connected to Internet before doing user registration and network configuration
1. Click Create Account
2. Enter your email address and
password, and then click
Registration
Caution:
It is better to log in your email box
and active your registration
account by clicking link in case you
forget the password.
It is necessary to forget any other
around network and make sure the
Android or IOS device just connect
to the WIFI network you want to
configure.
Make sure the Android or IOS
device WIFI function works well
and can be connected back to your
original WIFI network
automatically.
Using Android device to do
Network configuration.
VIVAX ENG
6
4. Network Configuration
Using Android or iOS device to do network configuration
1. Make sure your mobile device has already been connected to the Wi-Fi network which
you want to use. Also, you need to forget other irrelevant Wi-Fi network in case it
influences your configuration process. Disconnect the power supply of AC.
2. Connect the power supply of AC, and continuously press the LED DISPLAY or DO
NOT DISTURB button seven times in 10 seconds.
3. When the AC displays AP, it means that the AC Wi-Fi has already entered into AP
mode.
There are two ways to finish the network configuration:
1. Network configuration by Bluetooth scan
2. Network configuration by select appliance type
Network configuration by Bluetooth scan
Caution:
Make sure the bluetooth of
your mobile device is
working.
1. Press + Add
Device
2. Press Scan for nearby
devices
ENG VIVAX
7
3. Wait smart devices to
find, then click to add it.
4. Select home Wi-Fi,
enter the password.
5. Wait connecting to the
network.
6. Configuration Success,
you can modify the
default name.
VIVAX ENG
8
7. You can choose an
existing name or
customize a new
name.
8. Bluetooth network
configuration is
successful, now you
can see the device in
the list.
ENG VIVAX
9
Network configuration by select appliance
type
1. If the bluetooth network cofiguration is failure, please
select the appliance type.
2. Please follow the following steps to enter AP
mode:
a) Power on the device, wait 5 seconds, then click
Next.
Indice
