Vivo Link VL120021 Manuale utente
VL120021
4K HDBaseT 2.0™ Extender w/ HDMI® & USB 2.0
KVM support
User Manual
HDBaseT 2.0 KVM Extender Set
Preface
Read this user manual carefully before using this product. Pictures shown in this
manual is for reference only, different model and specifications are subject to real
product.
This manual is only for operation instruction only, not for any maintenance usage.
Trademarks
Product model and logo are trademarks. Any other trademarks mentioned in this
manual are acknowledged as the properties of the trademark owner. No part of this
publication may be copied or reproduced without prior written consent.
FCC Statement
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. It has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a commercial
installation.
Operation of this equipment in a residential area is likely to cause interference, in which
case the user at their own expense will be required to take whatever measures may be
necessary to correct the interference
Any changes or modifications not expressly approved by the manufacture would void
the user’s authority to operate the equipment.
HDBaseT 2.0 KVM Extender Set
SAFETY PRECAUTIONS
To insure the best from the product, please read all instructions carefully before using
the device. Save this manual for further reference.
Unpack the equipment carefully and save the original box and packing material for
possible future shipment
Follow basic safety precautions to reduce the risk of fire, electrical shock and injury
to persons.
Do not dismantle the housing or modify the module. It may result in electrical shock
or burn.
Using supplies or parts not meeting the products’ specifications may cause
damage, deterioration or malfunction.
Refer all servicing to qualified service personnel.
To prevent fire or shock hazard, do not expose the unit to rain, moisture or install
this product near water.
Do not put any heavy items on the extension cable in case of extrusion.
Do not remove the housing of the device as opening or removing housing may
expose you to dangerous voltage or other hazards.
Install the device in a place with fine ventilation to avoid damage caused by
overheat.
Keep the module away from liquids.
Spillage into the housing may result in fire, electrical shock, or equipment damage.
If an object or liquid falls or spills on to the housing, unplug the module immediately.
Do not twist or pull by force ends of the optical cable. It can cause malfunction.
Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to
the device before cleaning.
Unplug the power cord when left unused for a long period of time.
Information on disposal for scrapped devices: do not burn or mix with general
household waste, please treat them as normal electrical wastes.
HDBaseT 2.0 KVM Extender Set
Contents
1. Introduction.................................................................................................................1
1.1 Introduction to VL120021...................................................................................1
1.2 Features ............................................................................................................1
1.3 Packing List.......................................................................................................1
2. Panel Description........................................................................................................2
2.1 Transmitter.........................................................................................................2
2.2 Receiver ............................................................................................................3
3. System Connection.....................................................................................................5
3.1 Usage Precautions............................................................................................5
3.2 System Diagram................................................................................................5
3.3 Connection Procedure.......................................................................................5
3.4 Application.........................................................................................................6
4. Specification ...............................................................................................................7
4.1 Supported Resolution........................................................................................8
5. Panel Drawing ............................................................................................................9
6. Troubleshooting & Maintenance ...............................................................................10
7. After-sales Service....................................................................................................11
HDBaseT 2.0 KVM Extender Set
1
1. Introduction
1.1 Introduction to VL120021
Compliant with HDMI 2.0 & HDCP 2.2,VL120021 is a 4K HDMI Extender set developed
with the latest HDBaseT™ 2.0 technology to extend uncompressed HDMI video, audio,
USB 2.0, control signals and PoC over a single CAT5e/6 cable. The unidirectional PoC
compliant extender comes with only one power supply, which means that the Receiver
can be powered via Transmitter to save installers time and added cost to installing a
power outlet. Ideally designed for smart displays and KVM solutions fitting digital
signage markets.
1.2 Features
Compatible with HDMI2.0 and is backwards compatible with all previous HDMI
standards(e.g. HDMI 1.4), delivers high-resolution AV signal(1080p 3D,
4Kx2K@60Hz)
Support HDBT2.0, transmit 4Kx2K signal up to 100m over single CAT6 cable
EDID Pass-Thru
HDCP2.2 compliant
Front panel status LEDs for power, link & HDCP
USB & RS232 control
Unidirectional PoC (Power over HDBaseT)
1.3 Packing List
1 x Transmitter
1 x Receiver
4 x Detachable Mounting Ears
8 x Screws
1 x Power Adapter (DC 12V 2A)
8 x Plastic Cushions
2 x RS232 cables (Phoenix to 9 Pin D-Sub)
1 x User manual
Confirm if the product and the accessories are all included, if not, please contact
with the dealers.
HDBaseT 2.0 KVM Extender Set
2
2. Panel Description
2.1 Transmitter
No.
Name
Description
①
Indicators
Power:
OFF: No power
RED: DC power present
ON: Working status indicator
OFF: Not operational
Blinking GREEN: Normal operation
LINK: HDBT Link status indicator
OFF: No Link
GREEN: Link successful
Blinking GREEN: Link problem
HDCP: HDCP compliant indicator
OFF: No HDMI traffic(no picture)
GREEN: HDMI signal with HDCP
Blinking GREEN: HDMI signal without HDCP
②
FW
Micro USB port, used for firmware update.
Firmware updated need auxiliary equipment, please contact
with our after-sales department for more details.
③
HDMI IN
Connect with HDMI source.
④
HDBT OUT
Connect to the HDBT IN port on rear panel of the Receiver
via CAT5e/CAT6a cable, compliant with HDBT2.0 and
support unidirectional PoC to power the Receiver.
DC 12V
Tx Rx
RS232HDBT OUTHDMI IN USB OUT
FW
ON LINK HDCP
1
34567
2
Front
Rear
HDBaseT 2.0 KVM Extender Set
3
⑤
USB OUT
Type-B USB port, connect to PC to receive remote USB
control
⑥
RS232
Serial port, connects with control device or device to be
controlled, supports bi-directional RS232 control.
⑦
DC 12V
Connect with a DC12V 2Apower adapter.
Pictures for reference only, subject to our existing products.
2.2 Receiver
No.
Name
Description
①
Indicators
Power:
OFF: No power
RED: DC power present
ON: Working status indicator
OFF: Not operational
Blinking GREEN: Normal operation
LINK: HDBT Link status indicator
OFF: No Link
GREEN: Link successful
Blinking GREEN: Link problem
HDCP: HDCP compliant indicator
OFF: No HDMI traffic(no picture)
GREEN: HDMI signal with HDCP
Blinking GREEN: HDMI signal without HDCP
DC 12V
Tx Rx
HDBT IN
HDMI OUT USB IN RS232
USB IN
Tx Rx
HDBT IN
HDMI OUT RS232
FW
ON LINK HDCP
1
3456
2
Front
Rear
HDBaseT 2.0 KVM Extender Set
4
②
FW
Micro USB port, used for firmware update.
Firmware updated need auxiliary equipment, please contact
with our after-sales department for more details.
③
HDMI OUT
Connect with HDMI display.
④
HDBT IN
Connect to the HDBT OUT port on the Transmitter via CAT5e/
CAT6a cable, compliant with HDBT2.0.
⑤
USB IN
Type-A USB ports, connect to mouse/ keyboard/ U-disk for
remote USB access.
⑥
RS232
Serial port, connects with control device or device to be
controlled, supports bi-directional RS232 control.
Pictures for reference only, subject to our existing products.
HDBaseT 2.0 KVM Extender Set
5
3. System Connection
3.1 Usage Precautions
1) System should be installed in a clean environment and has a prop temperature and
humidity.
2) All of the power switches, plugs, sockets and power cords should be insulated and
safety.
3) All devices should be connected before power on.
3.2 System Diagram
3.3 Connection Procedure
Step1.Connect HDMI source (such as PC) to HDMI IN port of the Transmitter with an
HDMI cable.
Step2.Connect HDBT OUT port of the Transmitter to HDBT IN port of the Receiver
through a straight-thru CAT5e/CAT6 cable.
Step3.Connect a HDMI display to HDMI OUT port of the Receiver with HDMI cable;
Step4.When using the USB control, do the following:
a) Connect PC to the USB OUT port of Transmitter.
USB Signal:
RS232 Signal:
Receiver
USB IN
Tx Rx
HDBT IN
HDMI OUT RS232
Transmitter
DC 12V
Tx Rx
RS232HDBT OUTHDMI IN USB OUT
Display
DC 12V
PC Projector
Esc Print
SysRq
Screen Scro ll
Lock Pause
Break
Num
Lock Caps
Lock Scroll
Lock
Num
Lock /-
+
Enter
7
Home 89
PgUp
56
1
End 23
PgDn
0
Ins .
Del
~
`!
1@
2#
3$
4%
5^
6&
7*
8(
9)
0_
-+
=Backspace Home Page
Up
Page
Down
Insert
Delete End
Tab
CapsLock
Shift
Ctrl Alt Alt Ctrl
Shift
\
}
]
{
[
:
;
?
/
>
.
<
,
Enter
Q W E R T Y U I O P
A S D F G H J K L
Z X C V B N M
HDBaseT 2.0 KVM Extender Set
6
b) Connect Mouse/ Keyboard/U-disk to the USB IN port(s) of Receiver.
Step5.When using the bi-directional RS232 control, do the following:
a) Connect PC to the RS232 port at either the Transmitter or the Receiver.
b) Connect a third-party device (such as projector) need to be controlled to
the RS232 port at the other end.
c) Send RS232 commands to control the third-party device. For more details
about RS232 commands, please refer to the user manual for the third-
party device.
Step6.Connect with DC12V power adaptor to the power port of Transmitter, the
Receiver will be powered synchronously via PoC.
1) System Diagram shown in this manual is for reference only, more specific
schemes depend on real-time applications.
2) Connect HDBT ports via straight-thru CAT5e/6 cable with TIA/EIAT568B standard
terminations at both ends.
3) RS232 communication protocol: Baud Rate: 9600; data bit: 8; stop bit: 1; parity:
none. HDBT Transceiver receives RS232 control from devices with various baud
rate (2400, 4800, 9600, 19200, 38400, 57600, 115200).
4) HDBT ports can work with our company’s HDBT products that has same power
supply solution.
3.4 Application
Compliant with HDBT2.0, HDBaseT 2.0 KVM Extender Set has a good application in
occasions where high-definition AV distribution, long-distance transmission, Ethernet
Switch are needed, such as computer realm, monitoring, big screen displaying,
meeting room, education and bank & securities institution etc.
Indice
Altri manuali Vivo Link Estensione
Vivo Link
Vivo Link VLHDMIEXTHDB2.0 Manuale utente
Vivo Link
Vivo Link VLHDMIEXT421 Manuale utente
Vivo Link
Vivo Link VLHDMIEXTFIB Manuale utente
Vivo Link
Vivo Link VLHDMIEXT422 Manuale utente
Vivo Link
Vivo Link VLHDMIEXTDGL100 Manuale utente
Vivo Link
Vivo Link VL120006 Manuale utente
Vivo Link
Vivo Link VLHDMIEXTFIB Manuale utente
Vivo Link
Vivo Link VLUSBEXT50 Manuale utente
Vivo Link
Vivo Link VL120007 Manuale utente
Vivo Link
Vivo Link VLEXTA170 Manuale utente
