Vivotek FD8361 Manuale utente

FD8361

P/N:625010100G Ver.1.0

2 MP H.264 Day&Night Vandal-proof

EN - 1

English

Power off the Network Camera as

soon as smoke or unusual odors are

detected.

Contact your distributor in the event of

occurrence.

Refer to your user's manual for the

operating temperature.

Warning Before Installation

Do not place the Network Camera on

unsteady surfaces.

Do not touch the Network Camera

during a lightning storm.

Do not insert sharp or tiny objects

into the Network Camera.

Do not drop the Network Camera.

625010100G_QIG, FD8361_20091221_V.1.0.indd 1 2009/12/21 PM 05:20:54

EN - 2

Software CD

FD8361

Quick Installation Guide /

Warranty Card

Alignment Sticker /

Ceiling Hole Template Sticker

Bottom Base

Power Adapter

Package Contents

L-type Hex Key Wrench / RJ45 Female/Female Coupler / Slica Gel / Screws

FD8361

P/N:625010100G Ver.1.0

2 MP H.264 Day&Night Vandal-proof

Ceiling Hole Template Sticker

Drill hole

625010100G_QIG, FD8361_20091221_V.1.0.indd 2 2009/12/21 PM 05:20:57

EN - 3

English

SD/SDHC Card Slot

IR LEDs (18 units,

distance 20m)

Reccessed Reset

Button

N.C.

AC24V

Focus Controller

Zoom Controller

Status LED

Light Sensor

Physical Description

Pan Adjustment Screw

Inner View

Ethernet 10/100 RJ45 Plug

Audio Out (green)

Microphone In (pink)

Power Cord Socket (black)

General I/O Terminal Block

Ground

Fan

Operating environment: -20° ~ 50°C

When the temparature inside the Network

Camera reaches over 50°C, the fan will operate

automatically; when the temparature inside the

Network Camera drops to 0°C, the heater and fan

will both operate automatically.

BNC Video Output

Heater

Rotation Adjustment

Screw

Vari-focal Lens

(f= 3~9 mm)

Tilt Adjustment Screw

NTSC/PAL Video Output

Switch

625010100G_QIG, FD8361_20091221_V.1.0.indd 3 2009/12/21 PM 05:21:06

EN - 4

Record the MAC address under

the camera base before installing

the camera.

Network Camera

Model No: FD8361

Made in Taiwan

This device complies with part 15 of the FCC rules. Operation is subject to

the following two conditions:

(1)This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference

that may cause undesired operation.

Pat. 6,930,709

RoHS

V I

MAC:0002D1083236

CLASS A

IP66-rated Vandal-proof

Bottom Base

Outer View

IP66-rated Vandal-proof

Dome Cover

N.C.

AC24V

Camera Base

Hole a~c:

Holes to secure the bottom base.

625010100G_QIG, FD8361_20091221_V.1.0.indd 4 2009/12/21 PM 05:21:08

EN - 5

English

First, use a screwdriver to loose the three screws and detach the dome cover from the

camera base. Then, follow the steps below to install the camera to either a ceiling or a wall.

Hardware Installation

Ceiling mount (with the bottom base)

1. Attach the supplied alignment sticker to the ceiling.

2. Using the 10 circles on the sticker, drill at least 2 pilot holes symmetrically on each side into the ceil-

ing. Then hammer the four supplied plastic anchors into the holes.

3. Through the four holes on the bottom base, insert the four supplied screws into the corresponding

holes and secure the bottom base with a screwdriver.

4. Feed the cables through hole A or B. If you want to use hole B, remove the rubber stopper with a

screwdriver.

5. Secure the camera base to the bottom base with three supplied screws.

N.C.

AC24V

625010100G_QIG, FD8361_20091221_V.1.0.indd 5 2009/12/21 PM 05:21:16

EN - 6

Wall mount (with the bottom base)

1. Attach the supplied alignment sticker to the wall.

2. Using the 10 circles on the sticker, drill at least 2 pilot holes symmetrically on each side into the wall.

Then hammer the four supplied plastic anchors into the holes.

3. Using the four holes on the bottom base, insert the four supplied screws to corresponding holes and

secure the bottom base with a screwdriver.

4. Feed the cables through hole A or B. If you want to use hole B, remove the rubber stopper with a

screwdriver.

5. Secure the camera base to the bottom base with three supplied screws.

625010100G_QIG, FD8361_20091221_V.1.0.indd 6 2009/12/21 PM 05:21:24

EN - 7

English

General Connection (without PoE)

N.C.

AC24V

POWER C

OLLIS

ION

LINK

CEIVE

PARTITION

12345

Network Deployment

1. If you have external devices such as sensors and alarms, make the

connection from the general I/O terminal block.

2. Use the supplied RJ45 female/female coupler

to connect the Network Camera to a switch.

Use a Category 5 Cross Cable when Network

Camera is directly connected to PC.

3. Connect the power cable from the Network

Camera to a power outlet.

N.C.

AC24V

N.C.: No Connector

AC24V: Power in AC 24V

GND: Ground

DI : Digital Input

DO : Digital Output

+12V : Power, 12V DC

GND

+12V

Drop-ceiling mount (without the bottom base)

1. Attach the supplied ceiling hole template sticker to the ceiling.

2. Open a hole along the inner circle of the sticker.

3. Using the 3 circles on the sticker, drill 3 pilot holes into the ceiling. Then hammer the three supplied

plastic anchors into the holes.

4. Mount the Network Camera to the ceiling and feed the cables through.

5. Using the three holes on the side of the camera base, insert the three supplied screws into the cor-

responding holes and secure them with a screwdriver.

Ceiling Hole Template Sticker

Drill hole

625010100G_QIG, FD8361_20091221_V.1.0.indd 7 2009/12/21 PM 05:21:29

EN - 8

Power over Ethernet (PoE)

POWER COLLISION

LINK

RECEIVE

PARTITION

12345

N.C.

AC24V

PoE Switch

POWER COLLISION

LINK

RECEIVE

PARTITION

12345

N.C.

AC24V

When using a non-PoE switch

Use a PoE power injector (optional) to connect between the Network Camera and a

non-PoE switch.

When using a PoE-enabled switch

The Network Camera is PoE-compliant, allowing transmission of power and data via a

single Ethernet cable. Follow the below illustration to connect the Network Camera to a

PoE-enabled switch via Ethernet cable.

Non-PoE Switch

PoE Power Injector

(optional)

625010100G_QIG, FD8361_20091221_V.1.0.indd 8 2009/12/21 PM 05:21:31

EN - 9

English

Network Camera

Model No: FD8361

Made in Taiwan

This device complies with part 15 of the FCC rules. Operation is subject to

the following two conditions:

(1)This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference

that may cause undesired operation.

Pat. 6,930,709

RoHS

V I

MAC:0002D1083236

CLASS A

1. Install “Installation Wizard 2” from the Software Utility directory on the software CD.

2. The program will conduct an analysis of your network environment. After your network is

analyzed, please click on the “Next” button to continue the program.

3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network

Cameras on the same LAN.

4. After searching, the main installer window will pop up. Click on the MAC that matches the

one labeled on the bottom of your device to connect to the Network Camera via Internet

Explorer.

0002D1083236

00-02-D1-08-32-36 192.168.5.109 FD8361

Installation

Wizard 2

Assigning an IP Address

625010100G_QIG, FD8361_20091221_V.1.0.indd 9 2009/12/21 PM 05:21:33

Altri manuali per FD8361

Indice

Altri manuali Vivotek Telecamera di sicurezza

Vivotek

Vivotek CC8130 Manuale utente

Vivotek

Vivotek IP3112 Manuale utente

Vivotek

Vivotek IP8152 Manuale utente

Vivotek

Vivotek FE8191 Manuale utente

Vivotek

Vivotek SD8333-E/M Manuale utente

Vivotek

Vivotek SD8333-E Manuale utente

Vivotek

Vivotek FD8133V Manuale utente

Vivotek

Vivotek FD8133V Manuale utente

Vivotek

Vivotek MD8562 Manuale utente

Vivotek

Vivotek PT3117 Manuale utente

Vivotek

Vivotek FD8182-T Manuale utente

Vivotek

Vivotek IP7142 Manuale utente

Vivotek

Vivotek PZ8111 Manuale utente

Vivotek

Vivotek FE8172 Manuale utente

Vivotek

Vivotek IB8369A Manuale utente

Vivotek

Vivotek FD8166 Manuale utente

Vivotek

Vivotek FD8151V Manuale utente

Vivotek

Vivotek IP8166 Manuale utente

Vivotek

Vivotek IB9387 Series Manuale utente

Vivotek

Vivotek SD83X4E Manuale utente

Vivotek

Vivotek FD8166 Manuale utente

Vivotek

Vivotek IP7133 Manuale utente

Vivotek

Vivotek FD8166 Manuale utente

Vivotek

Vivotek Supreme SD83xxE Manuale utente

Manuali Telecamera di sicurezza popolari di altre marche

Okina USA

Okina USA SIR36-870VF650LP Manuale utente

Divio

Divio NDR155PA Manuale utente

Canon

Canon VB-C500D Manuale utente

Easy Access

Easy Access EasyGuard Manuale utente

TUYA

TUYA COSMO W2 Manuale utente

Eusso

Eusso UNC7500-IR Guida all'installazione

urmet domus

urmet domus 1096/204 Manuale utente

VC VC20 series Manuale utente

Axis

Axis Q1614 Manuale utente

ieGeek

ieGeek DD201 Manuale utente

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuale utente

Vicon

Vicon V662-D-1 Istruzioni operative

Grundig

Grundig GCH-K0274P Manuale utente

Lorex

Lorex VANTAGE LBC7032 Manuale utente

4xem

4xem WPT Manuale utente

Samsung

Samsung SCV-3082 Manuale utente

Vitek

Vitek VTC-C544 Manuale utente

Lumens

Lumens VC-A50PNW Manuale utente