Vivotek IP8336W Manuale utente

EN - 1

English

Warning Before Installation

Power off the Network Camera as

soon as smoke or unusual odors are

detected.

Keep the Network Camera away

from water. If the Network Camera

becomes wet, power off immediately.

Do not place the Network Camera

around heat sources, such as a

television or oven.

Refer to your user’s manual for the

operating temperature.

Keep the Network Camera away from

direct sunlight.

Do not place the Network Camera in

high humidity environments.

Do not place the Network Camera on

unsteady surfaces.

Do not touch the Network Camera

during a lightning storm.

Do not disassemble the Network

Camera.

Do not drop the Network Camera.

Do not insert sharp or tiny objects

into the Network Camera.

EN - 2

Camera Stand

Warranty Card

Screws

Quick Installation Guide

Power Adaptor (+12V, 2A)

Package Contents

Software CD

Antenna

IP8336W

EN - 3

English

Physical Description

Front Panel

Status LED

Lens

Microphone

Item LED status Description

LED Definitions

1 Steady Red Powered and system booting, or network failed

2 Blue LED blinks every 0.15 sec. Searching for WPS

3 Green LED blinks every 1 sec. Network connected to an AP

4 Green and RED blink consecutively every 0.15 sec. Upgrading firmware

5 Steady Blue Operating in camera default AP mode

6 Orange blinks every 0.15 sec. Restoring defaults

7 All LED off Powered off

Light Sensor

Antenna

Back Panel

Mounting Hole

Power and I/O Combo Cable

IR LEDs behind panel

EN - 4

Reset button

WPS button

NOTE:

An antenna comes with the camera. Install it by turning

clockwise to attach to the connector.

Network Deployment

1. If you have external devices such as a sensors and alarm, make connections from the

digital input connector.

2. Connect the power line to the power adaptor.

DI+

DI-

Power Connection

Bottom View

MicroSD/SDHC

Card Slot

EN - 5

English

WPS

Wireless Connection #1: Using the WPS Button

1. Make sure your AP (Access Point) and Operating System support WPS (Wi-Fi

Protected Setup) functions. WPS enables easy setup with compatible APs.

2. Use the included hex wrench to open the bottom cover.

3. Use the hex wrench to press the WPS button for 1 second.

The camera LED should flash green. When WPS configuration is done, wireless

connectivity will be established and the security encryption, such as WEP or WPA-

PSK, will be synchronized with the AP. Use the IW2 utility to find the camera. As for IP

setting, the camera's use of DHCP or static IP is determined by your configuration on the

network camera via the web-based configuration of firmware. The camera's default is

DHCP.

NOTE:

WPS Button

Wireless AP

1. WPS may not work if your AP is configured with a "hidden" SSID.

2. If no WPS-enabled AP is detected, the camera will continue searching for AP for 2

minutes. After that, the wireless setup will be cancelled.

When powered on, the camera LED should

light red for a minute, and then turn blue.

When lit blue, the camera operates in the AP

mode.

4. Press and hold down the WPS button on your AP (some router/AP will

have a virtual button on their management software instead). Refer to

your AP's documentation for details using its WPS functions.

EN - 6

Wireless Connection #2: Connection without WPS

2. Right-click or double-click on the VIVOTEK (MAC addr) icon. The camera name is

presented as: "VIVOTEK: (the last 4 digits of the camera's MAC address)."

Open a browser session using the camera's default IP "192.168.1.1"

If not using the WPS method, you can manually configure the camera:

1. Connect power to the camera. By default, the camera operates in the AP mode. Connect

to the camera using a Wi-Fi capable notebook or a computer with a wireless adaptor.

Open the internet dialog box by clicking the wireless networks icon on the system tray.

VIVOTEK (1C:CC)

AP mode

Client

mode

EN - 7

English

You can also discover the camera

using the IW2 utility. Install the IW2

utlity from the included product CD.

3. Enter your wireless AP's SSID and security password to connect to an existing AP. You

may also use the "Search your AP" button to locate an AP of your preferrence. Double-

click on an AP to make the connection.

Select the security encryption, such as

WEP or WPA-PSK, the algorithm, and

enter the pre-share key. Click Save to

proceed.

The camera will then operate in the

Client mode.

EN - 8

2011/01/05 01:50:28

5. A browser session with the Network Camera should prompt as shown below.

6. You should be able to see live video from your camera. You may also install the

32-channel recording software from the software CD in a deployment consisting of

multiple cameras. For its installation details, please refer to its related documents.

4. Open the IW2 utility. The camera will be assigned with a new IP address. Double-click

on it to start a web session. The camera LED will start blinking green by every second.

NOTE:

When you encounter configuration errors,

you can press the WPS button for 5

seconds to restore network settings. The

camera will resume the AP mode and the

LED will light blue.

WPS

EN - 9

English

Wireless Connection #3: Initial Setup Using a Cell Phone

VIVOTEK (1C:CC)

2. Once connected, you should connect the camera to

another AP. You should open a browser, enter the

camera's default IP (192.168.1.1) in the URL field.

When connected, manually enter the SSID and

security code for access to another AP, or use the

"Search your AP" function to search for nearby APs.

The search may take several seconds.

3. Select and connect to a preferred AP.

1. Connect power to the camera. Search for the camera in the Wi-Fi Networks. The camera

initially operates in the AP mode. Screen captures have been taken from an iPhone®.

Altri manuali per IP8336W

Indice

Altri manuali Vivotek Telecamera di sicurezza

Vivotek

Vivotek FD9187-H Manuale utente

Vivotek

Vivotek IP8355EH Manuale utente

Vivotek

Vivotek SD9365-EHL Manuale utente

Vivotek

Vivotek IP8364-C Manuale utente

Vivotek

Vivotek AM-214 Manuale utente

Vivotek

Vivotek TD5328-VF2 Manuale utente

Vivotek

Vivotek BD5336 Manuale utente

Vivotek

Vivotek Supreme FD8363 Manuale utente

Vivotek

Vivotek FE8173 Manuale utente

Vivotek

Vivotek IP8152 Manuale utente

Vivotek

Vivotek FD8165H Manuale utente

Vivotek

Vivotek Supreme MD8563-EH Manuale utente

Vivotek

Vivotek Supreme FE817V Manuale utente

Vivotek

Vivotek FD8156 Manuale utente

Vivotek

Vivotek IB9389-H Manuale utente

Vivotek

Vivotek FE8174V Manuale utente

Vivotek

Vivotek Supreme MD8564-EH Manuale utente

Vivotek

Vivotek 4X-SD8111 Manuale utente

Vivotek

Vivotek PZ6114 Manuale utente

Vivotek

Vivotek IP7160 Manuale utente

Vivotek

Vivotek IP8352 Manuale utente

Vivotek

Vivotek FD7141 Manuale utente

Vivotek

Vivotek IB9387-HT-A Manuale utente

Vivotek

Vivotek SUPREME IP9165-HP Manuale utente

Manuali Telecamera di sicurezza popolari di altre marche

Okina USA

Okina USA SIR36-870VF650LP Manuale utente

Divio

Divio NDR155PA Manuale utente

Canon

Canon VB-C500D Manuale utente

Easy Access

Easy Access EasyGuard Manuale utente

TUYA

TUYA COSMO W2 Manuale utente

Eusso

Eusso UNC7500-IR Guida all'installazione

urmet domus

urmet domus 1096/204 Manuale utente

VC VC20 series Manuale utente

Axis

Axis Q1614 Manuale utente

ieGeek

ieGeek DD201 Manuale utente

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuale utente

Vicon

Vicon V662-D-1 Istruzioni operative

Grundig

Grundig GCH-K0274P Manuale utente

Lorex

Lorex VANTAGE LBC7032 Manuale utente

4xem

4xem WPT Manuale utente

Samsung

Samsung SCV-3082 Manuale utente

Vitek

Vitek VTC-C544 Manuale utente

Lumens

Lumens VC-A50PNW Manuale utente