Vmarker Sensor II Manuale utente

MANUAL (EN)
MANUEL (FR)
HANDLEIDING (NL)
Interactive Whiteboard

version: Thursday 16 February 2017

EN
1 General
This manual is based on the Vmarker sensor II with firmware version 8 and Vmarker tility
software version 3.0. When using a different firmware or Vmarker tility, it is possible that
the explanation does not match the situation.
You can e-mail any suggestions for improving this manual to: ludwig@vmarker.org.
Vmarker Interactive Whiteboard 1

EN
2 Vmarker Sensor II
2.1 General
2.1.1 Front-side of the Vmarker sensor
You can recognize the front-side by the IR-filter: the dark-red nearly black shiny surface
with three coloured LED's. Behind this filter the IR-sensors are positioned. You have to
point this side in the direction of the projected image.
The most important sensor is positioned in the middle behind the IR-filter.
Pay attention that you do not damage this
filter: scratches on the IR-filter can disturb
the proper functioning of the Vmarker
sensor. You can clean the IR-filter with a dry
lint-free cloth.
The 3 colored LED's on the front indicate the status of the Vmarker sensor.
The red LED, indicates the state of the SB-connection.
The green LED, indicates the state of the calibration.
In normal operation mode the yellow LED indicates the sensing of an IR-dot. When the
Vmarker sensor is in calibration mode, the yellow LED indicates which corner has to be
identified.
The following table summarizes the possible states of the LEDs and the meaning.
RED LED GREEN LED YELLOW LED
off X X No connection to the computer or computer is switched off.
blinking X X Connected to the computer, but SB is not yet configured.
on - - Connected to the computer, SB is running.
on off X The sensor is not calibrated.
on 1x blinking
. . . .
X The Vmarker sensor is in calibration mode, the first corner, top-
left of the projected image must be identified with an IR pen.
on 2x blinking
.. .. .. ..
X The Vmarker sensor is in calibration mode, the second corner,
top-right has to be identified.
on 3x blinking
... ... ... ...
X The Vmarker sensor is in calibration mode, the third corner,
bottom-right has to be identified.
on 4x blinking
.... .... .... ....
X The Vmarker sensor is in calibration mode, the fourth corner,
bottom-left has to be identified.
on on off The Vmarker sensor is calibrated
on on on The Vmarker sensor is calibrated, and detects an IR-dot
blinking blinking blinking The Vmarker sensor is in firmware update modus.
2 Vmarker Interactive Whiteboard
RED YELLOW
GREEN

EN
2.1.2 The back-side of the Vmarker sensor
On the back-side of the Vmarker sensor is an SB port type B.
With a standard SB A-B cable you can connect the Vmarker sensor with a standard SB
port on you computer. Note that the maximum length of 5m must not be exceeded.
If you want to use longer cable, you have to use an SB active extension cable.
2.1.3 The bottom-side of the Vmarker sensor
The bottom of the Vmarker sensor has a threaded hole. The common thread is 1 / 4 "BSW
this is used for camera mounts.
Vmarker Interactive Whiteboard 3
1/4” BSW
SB

EN
2.2 Arrangement of the Vmarker sensor
ATTENTION: make use of the correct tools and follow the appropriate safety
guidelines when installing the Vmarker sensor to the ceiling.
The arrangement of the Vmarker sensor depends on the position of the projected image.
Nevertheless we want to give you some recommendations.
A good aspect ratio of a projector is 16:10 (1280x800). Given the accessibility of the
screen for an average person, with such projector the effective image is about 1.92 meter
wide and 1.2 meters high.
The optimal distance (A) from the Vmarker sensor to the image is approximately 1.5 times
the width (B) of the image.
Attention also read 2. 2 .6 .About the projection surface and 2. 2 .7 .Environment
You will find some important information that affects the setup of the Vmarker
sensor.
4 Vmarker Interactive Whiteboard
EFFECTIVE
IMAGE 16:10
B=image width
H= image heigth
Whiteboard or
other white
surface

EN
2.2.1 Setu of the Vmarker sensor when using a ceiling mount
You get the best results with the Vmarker sensor by mounting the Vmarker sensor to the
ceiling like the projector itself. In most cases the Vmarker sensor will be positioned
between the projection screen and the projector, just outside the projector beam. This
depends on the type of projector.
The shortest distance (A) between the projection screen and the Vmarker sensor has to be
1.5 times the width of the projected image (B).
These values are guidelines for the optimal conditions, the settings of the Vmarker sensor
are optimized for this setup.
On the ‘Settings’ page of the Vmarker tility you can observe the coordinates
of the IR-pen in the section ‘Sensor status’. When you move the IR-pen
across the projected screen you should always get values for Object X-position,
Object Y-position and Object size. If this is not the case you have to re-align the Vmarker
sensor. Particular the corners of the image are important to be able to calibrate the
Vmarker sensor.
With help of the Sensor alignment in Vmarker tility you can easily align the Vmarker
sensor in most circumstances.
Vmarker Interactive Whiteboard 5
A = 1.5 x B (image width)
White Board or
other white
surface

EN
2.2.2 Setu of the Vmarker sensor using a tri od
The guidelines for the Vmarker sensor setup with a tripod are similar to the ceiling mount.
You just have to adapt to the situation, mostly the tripod is standing on a table.
The choice of the location of the Vmarker sensor is important to be able to use the IR-pen
more comfortably. Important is that the Vmarker sensor is able to 'see' the IR-LED while
writing.
In stead of placing the sensor in the middle of the projected image, you can move the
sensor either to the left or to the right side of the center. The left side if you are right
handed, the right side if you are left-handed.
6 Vmarker Interactive Whiteboard
B= image width
A >= B(image width)
Pos1
Pos2
Vmarker sensor
IR-pen

EN
2.2.3 Setu of the Vmarker sensor using a s ecial suction cu
It is also possible to stick it to the projector using a special suction cup. This is very easy,
but not every projector is suited.
The projector has to have a smooth surface where you can stick the suction cup on. Also
the projection distance of the projector is more important, a short-throw projector is not
suited.
Like in the other configurations the distance(A) between the projection screen and the
Vmarker sensor has to be at least 1.5 times the width of the projected image (B). In this
arrangement this means the projector is also at this distance.
Vmarker Interactive Whiteboard 7
A > 1.5 x B (image width)
White Board or
other white
surface
Vmarker sensor
on suction cup

EN
2.2.4 Setu of the Vmarker sensor in a “rear rojection” configuration
With rear-projection, the projector is positioned behind the screen. The projected image is
visible through the screen. In such an arrangement the Vmarker sensor can also be
positioned behind the screen.
This is because the IR light from the IR pen, like the light from the projection, also shines
through the screen.
The disadvantage of such an arrangement is that you need extra space behind the screen.
This may be reduced by using mirrors, etc.
2.2.5 Other setu s
Basically, the Vmarker sensor works almost from any angle. You have to ensure that the
projected image is within range of the Vmarker sensor.
The use of extreme angle is possible but is strongly depending on the projection surface
that is used. Also the angle of the IR-pen to the surface will have a greater influence.
In such case one can change a few settings of the Vmarker sensor to optimize to this
situation.
When using extreme angles also take into account that the accuracy will be reduced.
Ideally, you should try to use the entire range of the sensor that has a ratio of 1:1. You can
see the usage of the sensor after calibration on the Calibration page in the Vmarker tility.
2.2.6 About the rojection surface
It is possible to use the Vmarker sensor on many different projection surfaces. Every
surface that reflects the IR-light of the IR-pen can be used. But of course some are better
then other.
Contrary to what one would expect, highly reflective surfaces are not the best choice. A
matte white surface is basically better than a glossy white surface. The reflection on a
glossy surface is very high and the angle of the IR pen to the surface is more important. A
wrong angle of the IR-pen is missed by the Vmarker sensor. Therefore, a more matte
surface, in which case the reflection is diffuse, is better. The angle of the pen to the plane
becomes less important.
One of the best surfaces to use for your IWB would be a wall, simply painted in
white.
2.2.7 Environment
The Vmarker sensor responds to infrared light. Avoid any other source of infra-red light in
the range of the Vmarker sensor. The largest source of infra-red light is the sun. Direct
sunlight or reflection of sunlight directly into the Vmarker sensor or on the projected image,
will affect correct functioning of the Vmarker sensor. It is even possible that the mouse-
cursor moves seemingly randomly.
Other sources of far infra-red light in their spectrum can also be disruptive. In such case,
much depends on the situation.
8 Vmarker Interactive Whiteboard
Questo manuale è adatto per i seguenti modelli
1
Indice

















