VOGELS PFF7810 Manuale utente
PFF7810
Video Wall Floor Stand 3x3 for 46 Inch Displays
1
www.vogels.com
INSTALLATION INSTRUCTIONS
9589-007-Z00-01
1/2-13 x 4” Bolt
1/2”-13 Nut
1/2”-13 Washer
1/4”-20 x 3.75” Bolt
1/4” -20 Washer
1/4” -20 Washer
1/4”-20 Nut
1/2”-13 x 4” Bolt 1/2”-13 Nut
1/2” -13 Washer
Level
Step 1
Step 2
Step 3
2
www.vogels.com
Display mounting hardware
Display
Center Marker
Start by installing the lower center monitor
rst to the video wall frame and loosely
secure as shown.
Preparing brackets
for installation
Securing brackets
when installed
Install the left and right adjustable mounting
brackets to the displays aligning the "V" notch
on the display mounting plate to the rear center
height of the display. See arrow to center notch.
Note: lower round security rings on the mounting
bracket need to face to the center of the display.
See arrow.
Once center of display alignment is conrmed,
securely tighten all mounting bracket to display
mounting screws with correct pitch hardware
supplied.
Insure the three "V" alignment notches on each
mounting bracket are at their factory preset
center with all notches together to indicate you
are in the center of your alignment adjustment
eld. If not in center alignment, adjust the top
Allen head screw(s) to adjust the center to the
correct starting position on each mounting
bracket.
See arrow.
Step 4
Step 5
3
www.vogels.com
LevelLevel In/OutIn/Out
TiltTilt
Now that you have your rst lower center
display attached to the frame, the beauty of
the three part alignment features of the
mounting bracket come into play. The fact that
all the adjustments are on top will make the
nal adjusting eortless.
With your Vogel's spirit level in hand, rst place
the level on top of the display bezel to set side to
side level. Next, place the level on the face of the
display to adjust top to bottom level of the
display parallel to the frame. Once you have these
steps conrmed, make sure the mounted display
is center on the video wall frame left to right and
tighten the security screws to secure the display
to the round wall frames to further prevent side
to side movement.
Next, follow the same steps for the lower left and
right displays.
Once all three display are aligned and secured,
the nal ne adjustment of tilt and in/out can be
used to insure all bezel edges are closely aligned.
This will take a few adjustments back and forth to
determine nal screen adjustment.
With the lower two or three display properly
aligned you can move up to the second row,
following the same procedure as the rst row.
It is important that the time be taken to maximize
the rst row alignment before moving up as you
do not want to have to go back and forth
between rows. If done correctly your bezel edges
should match very closely top and bottom.
Step 6
4
www.vogels.com
As you are installing the second and possible third
level of monitors to the frame, you want to insure
there is proper minimal bezel edge clearance
between the upper and lower display. Some
models have sensitive materials incorporated in
the top and bottom edges of their display that do
not allow for resting the weights of the display on
top of each other. Side to side clearance of bezel
edges is equally as important for natural chassis
expansion that occurs as the display come up to
full operating temperatures. Without the minimal
clearance allowance, the display would push
against each other causing some potential distor-
tion of the chassis alignment.
Use a standard business card fold in half to double
its thickness and use this to set your minimum
clearance between display; not only top to
bottom, but also side to side for better over all
symmetry for the nished video wall. The business
card should slide with ease the total length of the
bezel edge. If not, adjust the clearance to allow for
smooth movement of the card. This should be
done at each level of monitors being installed
before moving up to the next row of monitors.
Use the bracket upper level screws to set the
upper and lower bezel edge clearance, and the
side to side security screw to adjust the side
clearance.
Note: A .05” gap between bezels is
recommended for heat expansions.
Step 7
www.vogels.com 5
Indice
Altri manuali VOGELS Rack e supporto
VOGELS
VOGELS PFW 6850 Manuale utente
VOGELS
VOGELS PPC 1500 Manuale utente
VOGELS
VOGELS INT8201 Manuale utente
VOGELS
VOGELS NEXT 8375 Manuale utente
VOGELS
VOGELS THIN 550 Manuale utente
VOGELS
VOGELS WALL 1025 Manuale utente
VOGELS
VOGELS EFW 8105 Manuale utente
VOGELS
VOGELS NEXT 7825 Manuale utente
VOGELS
VOGELS WALL 2250 Manuale utente
VOGELS
VOGELS PFW6857 Manuale utente
VOGELS
VOGELS TVA 6950 Manuale utente
VOGELS
VOGELS THIN 525 Manuale utente
VOGELS
VOGELS THIN 595 Manuale utente
VOGELS
VOGELS EFWE 6455 RC - MOUNTING Manuale utente
VOGELS
VOGELS TVB 2375 Manuale utente
VOGELS
VOGELS RISE 5105 Manuale di istruzioni
VOGELS
VOGELS NEXT 7355 Guida all'installazione
VOGELS
VOGELS EPA 6505 Manuale utente
VOGELS
VOGELS SOUND 3450 Manuale utente
VOGELS
VOGELS PFA 9134 Manuale utente
