Vonets VAR1200-H Istruzioni utente
VONETS——Gigabit Industrial Bridge Repeater
Gigabit Industrial Bridge Repeater
VAR1200-H/VAR1200-L/VAR1800-H/
VAR1800-L/VAR600-H/VAR600-L
Quick Setting Guide
Statement
Copyright © 2022 Shenzhen Houtian Network Communication Technology Co., Ltd.
Copyright, all rights reserved
Without the express written permission of Shenzhen Houtian Network Communication
Technology Co., Ltd., no unit or individual may copy, copy, transcribe or translate part or all
of the contents of this book. Not to be used for commercial or profit-making purposes in any
VONETS——Gigabit Industrial Bridge Repeater
form or by any means (electronic, mechanical, photocopying, recording or other possible
means).
VONETS is a registered trademark of Shenzhen Houtian Network Communication
Technology Co., Ltd. All other trademarks or registered trademarks mentioned in this
document are the property of their respective owners. The product specifications and
information mentioned in this manual are for reference only and may be updated without
prior notice. Unless there is a special agreement, this manual is only used as a guide, and all
statements, information, etc. in this manual do not constitute any form of guarantee.
Notice
The parameters used in the screenshots shown in this manual are only for reference of
setting examples and may not be completely consistent with the actual situation. Please set
the parameters according to your actual needs.
Due to different software versions, the screenshots shown in this manual may not be exactly
the same as the web interface of the product you purchased. Please configure your product
according to the actual web interface.
Product application and secondary development precautions
1. Problems related to wireless interference:
1.1 Use the ping command to test the wireless transmission performance. If it is
found that the delay of the ping packet response is extremely uneven, and there are
many responses with a large delay, it can basically be judged that the wireless has
been strongly interfered;
1.2 The product antenna should be kept as far away as possible from sources of
interference, such as switching power supplies, antennas of other modules or
wireless products, etc.;
1.3 If it is too close to the antenna of other wireless products, it will cause mutual
interference, resulting in an increase in the transmission bit error rate and a slower
transmission rate. At this point, the wireless signal must be properly attenuated. The
methods of attenuating the signal include adding obstacles, extending the distance,
and adding a resistor in series between the antenna feed point and the antenna, etc.,
to meet the actual application requirements;
2. Selecting a suitable power supply is the key to good and stable wireless transmission and
stable operation of the product. Improper power supply will cause damage to the product or
poor wireless performance. The selected power supply must meet the voltage range and
input power requirements of the power supply input, and the ripple must be less than the
required maximum power supply ripple (100mV);
VONETS——Gigabit Industrial Bridge Repeater
3. POE related issues:
3.1 If the product has PSE function (POE output), it needs 48V power supply voltage
and meets the power requirements of POE output before it can be used;
3.2 If the network port of the product has a POE output port, if it is connected to
other non-POE network ports, please use it with caution, and ensure that the access
network port is isolated from the ground, otherwise it may cause damage to the
connected product!
The safest way is: let the product use a two-pin switching power supply without
ground (AC TO DC, AC input is two-pin instead of three-pin).
The adapter power supply in all the schematic diagrams shown in the
following figures are externally connected to the power supply.
Transmission distance parameter table (Table 1)
Model
Number
Antenna
type
Frequency Band
Barrier-free
point-to-point
transmission
distance(for
reference only)
Transmission Rate
（Mbps）
VAR1200-L
Built in
2.4GHz
300m--400m
300
Notice:
In the actual application environment, if the POE output port (PSE) is connected to a
non-POE network port (PD is an access network port), please use it with caution, and
ensure that the access network port is isolated from the power ground, otherwise it may
cause the access device to fail. damage! When the power input is 48V (≥57W), the POE
output is valid!
Power Supply Parameter Table (Table 2)
Model Number
Wide voltage power supply
Output
Power
Typical
power
supply
Ripple
VAR1200-L
No POE output
power supply
DC12V--48V
≥30W
12V/3A
<100mV
With POE
output power
supply
DC48V
≥57W
48V/1.2A
<200mV
The standard kit of this product does not include a power supply, please select the power
supply carefully according to "Table 2", otherwise the product may be damaged or the WiFi
performance may be degraded.
VONETS——Gigabit Industrial Bridge Repeater
Contents
Chapter 1 Application Mode............................................................................................................................................... 1
1.1 Bridge + Repeater Mode(In the actual application environment, if the POE output port (PSE) is
connected to a non-POE network port (PD is an access network port), please use it with caution,
and ensure that the access network port is isolated from the power supply ground, otherwise it
may cause the access device. damage!)................................................................................................................. 1
1.2 Router Mode(In the actual application environment, if the POE output port (PSE) is connected
to a non-POE network port (PD is an access network port), please use it with caution, and ensure
that the access network port is isolated from the power supply ground, otherwise it may cause the
access device. damage!)................................................................................................................................................ 2
Chapter 2 Bridge+Repeater Mode Configuration Instruction................................................................................3
2.1 Device connect(In the actual application environment, if the POE output port (PSE) is
connected to a non-POE network port (PD is an access network port), please use it with caution,
and ensure that the access network port is isolated from the power supply ground, otherwise it
may cause the access device. damage!)................................................................................................................. 3
2.2 Bridge+Repeater Application Configuration .................................................................................................... 4
2.3 AP Application Configuration................................................................................................................................. 6
Chapter 3 Router Mode Configuration Instruction.....................................................................................................8
3.1 Change device mode (In the actual application environment, if the POE output port (PSE) is
connected to a non-POE network port (PD is an access network port), please use it with caution,
and ensure that the access network port is isolated from the power supply ground, otherwise it
may cause the access device. damage!)................................................................................................................. 8
3.2 WAN port settings.................................................................................................................................................... 10
3.2.1 WAN/LAN exchange .......................................................................................................................................10
3.2.2 WAN Port connection method.................................................................................................................... 10
3.2.3 WAN port wired connect network——DHCP........................................................................................11
3.2.4 PPPoE WAN port wired connect network——PPPoE ......................................................................11
3.2.5 WAN port wireless connect network---- WiFi........................................................................................11
3.3 Set WiFi hotspot parameters............................................................................................................................... 14
Chapter 4 Other components and installation method..........................................................................................15
4.1 Other components................................................................................................................................................... 15
4.2 Industrial chassis rail hook kit installation...................................................................................................... 16
Appendix Frequently Asked Questions....................................................................................................................... 16
VONETS——Gigabit Industrial Bridge Repeater
1
Chapter 1 Application Mode
1.1 Bridge + Repeater Mode(In the actual application environment, if the POE output
port (PSE) is connected to a non-POE network port (PD is an access network port),
please use it with caution, and ensure that the access network port is isolated from
the power supply ground, otherwise it may cause the access device. damage!)
There are three application modes for the bridge mode of VONETS device: WiFi repeater,
WiFi bridge and WiFi AP.
WiFi Repeater:
VONETS device as WiFi Repeater, it must be configured to source WiFi hostpot
parameters, can be used to extend the wireless signal coverage of existing APs or wifi
router .
WiFi Bridge:
VONETS device as WiFi bridge, it must be configured to source WiFi hotspot
parameters, can be used for devices only with Ethernet ports to access wireless
networks.
WiFi AP：
VONETS device as WiFi AP, it can achieve wireless access to wired LAN, no
configuration required, plug and play.
VONETS——Gigabit Industrial Bridge Repeater
2
1.2 Router Mode(In the actual application environment, if the POE output port (PSE) is
connected to a non-POE network port (PD is an access network port), please use it
with caution, and ensure that the access network port is isolated from the power
supply ground, otherwise it may cause the access device. damage!)
The VONETS device is used as a wireless router. The default Ethernet port is the WAN
port, and the default Ethernet cable is the LAN port. The WAN and LAN ports are
interchangeable (the shell is marked with WAN/LAN ports);
The VONETS device is used as a wireless router, and the WAN port can be set to
connect to a WiFi hotspot and used as a secondary router. Its Ethernet port and Ethernet
cable are both LAN ports.
VONETS——Gigabit Industrial Bridge Repeater
3
Chapter 2 Bridge+Repeater Mode Configuration Instruction
2.1 Device connect(In the actual application environment, if the POE output port (PSE)
is connected to a non-POE network port (PD is an access network port), please use it
with caution, and ensure that the access network port is isolated from the power
supply ground, otherwise it may cause the access device. damage!)
Power on VONETS device by 12V/3A power supply, then connect to PC, there are two
connection ways as below:
A. Computer is wired connected to LAN port of VONETS device;
（Recommend Method）
B. The computer wirelessly connects to the WiFi signal of VONETS device, its default
hotspot parameters are as follows:
WiFi SSID: VONETS_****** (corresponding to VONETS device MAC address)
WiFi password: 12345678
（After the WiFi parameters are configured, the WiFi will be disconnected, that is normal.）
VONETS——Gigabit Industrial Bridge Repeater
4
2.2 Bridge+Repeater Application Configuration
The configuration steps of VONETS device for WiFi repeater and WiFi bridge are basically
the same, so this manual combines the configuration instructions of the two application
modes.
1. After computer is connected to VONETS device, open browser, input configured page:
http://vonets.cfg (or IP: 192.168.254.254), then press Enter;
2. Input User name and Password in login page (both are “admin”), click “Login” button to
enter configured page;
3. “Scan Hotspots”, choose the source hotspots, click “Next”;
4. Input “Source wireless hotspot password”, click “Apply”;
IP layer transparent transmission (factory default), transparent transmission of IP
layer data, can meet most of WiFi bridge applications;
MAC layer transparent transmission, transparent transmission of all data above the
MAC layer (link layer) and MAC layer, including IP layer data. MAC transparent
transmission can solve some special applications for MAC layer encryption, such as
VONETS——Gigabit Industrial Bridge Repeater
5
GoPro camera, Cisco AP, Hikvision monitoring system, etc;
The option “The configuration parameters of WiFi repeater security is
synchronized with source hotspot” is default ticked, it means the SSID of VONETS
repeater is associated with the SSID of the source hotspot, and the WiFi password is the
same as the password of the source hotspot;
Disable hotspot, if you select “Disable hotspot” on the right side of the SSID, the device
will not transmit the corresponding hotspot and can only be used as a bridge application;
Advanced Setting,include Hot spot authentication match mode, WiFi Signal Motion
Detection and SSA Signal strength alarm threshold,these options here can be kept
unchanged, for instructions on this option, go to www.vonets.com and download the “V
Series WiFi Bridge Advanced Features Instruction”;
5. Click “Reboot”, VONETS device will connect to the configured WiFi hotspot automatically,
if connection is successful, the WiFi LED light will flash quickly;
VONETS——Gigabit Industrial Bridge Repeater
6
Model
Blue Light
Yellow Light
Red Light
VAR1200-L
2.4G Connection
Status Light
Ethernet Cable
Connection
Status Light
POE Output
connection
light
2.3 AP Application Configuration
VONETS device can be configured as an AP application, the wireless terminal device can
connect to VONETS device hotspot to connect to the network; however, it is best to change
its WiFi name and password for network security.
1. Log in to the configuration page http://vonets.cfg (or IP: 192.168.254.254you’re your
computer browser, both user name and password are “admin”;
2. Change the WIFI name: select "Basic Settings" in "WIFI Relay", enter the new WIFI
name in the text box after the SSID, and click the "Apply" button;
Note: There are a total of 6 hotspots in dual-band, you can set the account name and
password accordingly;
Questo manuale è adatto per i seguenti modelli
5
Indice
Altri manuali Vonets Ripetitore
Vonets
Vonets VRP300-PLUS Istruzioni utente
Vonets
Vonets VRP150 Istruzioni utente
Vonets
Vonets VAP11G-500 Istruzioni utente
Vonets
Vonets VRP150 Istruzioni utente
Vonets
Vonets MINI300 Istruzioni utente
Vonets
Vonets VAP11G-300 Guida all'installazione
Vonets
Vonets VAP11G-300 Istruzioni utente
Vonets
Vonets VAP11G-300 Istruzioni utente
Vonets
Vonets VRP5G Istruzioni utente
