VULX MAGMA Manuale utente
EN
INSTALLATION AND USER’S MANUAL
VULX MAGMA BARBEQUE TABLE
You’ve just acquired a VULX branded product.
This product has been manufactured with care and submitted to many control
tests, certifying it to CE EN 498 et EN 1860-1 standards.
Please read this manual carefully to use and maintain your VULX MAGMA
barbeque table safely and correctly.
Please keep this installations and user’s manual safely.
CONTENT
1. GENERAL SAFETY INSTRUCTIONS
2. ASSEMBLY
2.1 GAS SYSTEM
2.2 CHARCOAL SYSTEM
2.3 FROM GAS SYSTEM TO CHARCOAL SYSYEM AND BACK
3. USE
4. COOKING
5. MAINTENANCE
6. GAS SPECIFICATIONS
7. WARRANTY
8. ACCESSORIES
1. GENERAL SAFETY INSTRUCTIONS
Before use, check that no part or element of the VULX MAGMA barbeque table is
deformed damaged or unscrewed.
•Only for use outside
•Consult the instructions before using
•CAUTION: Accessible parts can be very hot. Keep away from
young children
•This device must be kept away from flammable materials during
use
•Do not move the device when using
•Close the gas valve after use
•Do not modify the device
•Do not close the ventilation openings of the gas cylinder’s slot
•The propane gas cylinder must be replaced when necessary
(away from any source of fire)
•Do not use in enclosed spaces!
•WARNING! This barbecue will become very hot. Do not move
during use.
•Never spray with water to extinguish the flame!
WARNING! Do not use alcohol or petrol to ignite or reactivate the
fire! Only use firelighters that comply with the EN 1860-3
standard!
WARNING! Do not leave the barbecue accessible to children and
pets.
2- ASSEMBLY
Assemble your VULX MAGMA barbeque table on a clean and level floor surface –
protect floor with cardboard or other material to prevent damage
TOOLS REQUIRED
1 BTR wrench size 4
1 metric wrench size 10 (flat, hexagon or pipe)
2 metric wrenches size 13 (flat, hexagon or pipe)
1 screwing device or screwdriver for cross head screws
1
Place the panel with the hole surrounded by rubber on the ground.
Make sure the VULX logo is facing the ground (outside surface)
Screw 4 black hexagon socket screws M6x20 in the screw holes in the panel for
the gas tube (the hole surrounded by rubber)
2
Place and screw the 2 legs without cut-outs onto the panel (2 at bottom of
picture)
3
Place the panel (below left) with the open side upwards onto the 2 screws of the
assembled part
Assemble with 2 M6 nuts, do not screw tightly.
4
Place the panel (see below) as shown onto the 2 screws on the lower wide part
of the structure.
Assemble with 2 M6 nuts, do not screw tightly.
5
Assemble the two side panels making sure the VULX Logo is legible and facing
outwards.
Fix in place using 2 black hexagon socket screws M6x20 and 2 M6 nuts (do not
screw tightly) in the two lower holes (see below)
6
Assemble the remaining 2 legs as shown below. They slot in between the
horizontal panels and the side panels.
Fix in place using 2 black hexagon socket screws M6x20 and 2 M6 nuts (do not
screw tightly), in the 2 lower holes in the legs, while the side panels and the
horizontal panels are squeezed together.
7
Assemble the 2 holders for the grease collection tray (see below). Make sure,
they are facing the right way. Fix in place using 2 black hexagon socket screws
M6x20 and 2 M6 nuts, slotting between the panels, legs and top panel.
9
8
Assemble the small top panel with 2 black hexagon socket screws M6x20 and 2
M6 nuts, screwing into the 2 remaining holes at top of legs.
Make sure it is screwed on as high as possible.
9
Tighten all the screws and nuts
10
Place the VULX MAGMA barbeque table upright.
11
Place the upper cone on the base aligning as shown in the diagram below (side
hole in line with the hole surrounded by rubber)
Indice
Altri manuali VULX Griglia
