WAFER GSM-HOUSE Manuale utente

GSM-HOUSE INTERCOM UNIT

GSM-HOUSE MANUAL

New version V2.3/2019

GSM-HOUSE INTERCOM UNIT

GSM-HOUSE OPERATING INSTRUCTIONS

PRODUCT DESCRIPTION

GSM-HOUSE is an anti-vandal GSM intercom with self contained GSM door entry audio

intercom system and also built-in the WAFER “GSM-KEY”function.

For the GSM intercom function.the vistor can call the authorization number via the “Call”

button to establish a voice connection. Door release is from the phone keypad during the talking..

For the "GSM-KEY" function, the device has a whitelist that allows call control. When the

GSM-HOUSE receives a call, it will check if the call number is in the whitelist. If in the list, it

will control the relay output on the device while rejecting the call.

It also has two alarm input ports for security detection. And also has a rechargeable backup

battery inside to provide continuous work when the power is temporarily suspended.

CONNECTOR DESCRIPTION

D2: MCU Led D6: GSM Led D3: SMS Receiving Status Led

When use DC power

input, there is no need to

distinguish which is

positive and which is

negative

GSM-HOUSE INTERCOM UNIT

INSTALLATION

To install the GSM-HOUSE, you need to connect the 2 wires of the relay contact in parallel

with the gate opening button. The relay contacts can stand 30V 2A maximum, this is enough for

its operation but don't try to switch higher voltages or currents. You should install the

GSM-HOUSE in a place with good GSM signal. Check it with a phone before proceeding with

the installation. If it is to be installed in a weak signal,consider using the magnetic mount GSM

antenna for better signal gain.

You should then insert the SIM Card of the operator you want to use with the right direction

according to the following pictures.

!Note! : You must remove the PIN request from the SIM before inserting it in the

unit, otherwise the device will not work. In order to do so, insert the SIM in a mobile phone and

verify the SIM card to call other phone and send and receive the SMS).

Lock the SIM card in the right direction:

GSM-HOUSE also comes with additional 2 Input.The inputs can be used to generate alarms

when triggered. For examples,you can can connect the door or gate saftey beam output to the

GSM-HOUSE Alarm1 and Alarm2 input.

Before the following test,Connect the DC12V to the AC/DC power input terminal.

Lock the panel

Insert the key, gently press and turn the key left to pull out the front panel. Gently press the key

and turn it to the vertical position to lock the front panel and eject the key.

Please read this entire manual before installation !Note!

Take EXTREME care with the Power line installation

In case of fault power connection will cause the default permanently.

To maximum reception, install the GSM antenna in a prominent elevated position if

possible, and vertically mounted.

The GSM unit requires mounting carefully with the lock for proper operation.

1.Slide back the SIM door and

lift it up

2.Slide the SIM Card into the

SIM door making sure that

the clipped corner of the SIM

card lines up with the clipped

corner of the SIM holder

3.Close the SIM door

4.Slide the SIM door to lock the

SIM card in place

GSM-HOUSE INTERCOM UNIT

OPERATION mode:

Visitor mode:

When the visitor pushes the call button,the device initiates a voice call to the configured phone

number,if the called person accepts the call,the communication establishes for the configured

duration.During the call,the connection can be stopped by pressing the button again.The call is

ended automatically when the configured communication time expires or the called party ends the

call. The next numbers is called if the previous number doesn’t answer.

Controlling the relay output

The DOOR RELEASE (Normally open,NO) relay output can be controlled as follows,depending

on the usage:

Controlling during the intercom call:

During a call,the user press “111”to open the relay1 and press “222”to open the relay2

Controlling by free call

On incoming call,after indentifying the caller ID,the unit reject the call and activates the

output,maximum 200 numbers can be configured

Controlling by SMS command or customized command

Please refer to the following SMS command to control the relay1 and relay2 and also can use the

customized SMS command to control

Teach button (Device Reset button)

Press the KEY button to Teach

Press the KEY and hold the button for around 2 second, the LED D4 would be lit,and then use

your phone to call the device number. when coming the call, device would reject the calling and

D4 would flash two times, then the number is saved. After program, press the button again to quit

the teaching. then the LED D4 would be extinguished.

(Fast button only program WHL position from WHL01 to WHL10)

Press the KEY button to Reset

Press the KEY button and hold the button for around 10 seconds,and then the LED would start to

flash and then release the button.The device has been reset.the Password would be reset to

“123456”and from WHL01 to WHL10 would be cleared.and other parameters such as ACM,

REPLY and REPORT will be reset to ACM=OFF,REPLY=ON,REPORT=ON.

Status LEDs

D2: MCU Led D6: GSM Led D3: SMS Receiving Status Led

D2: Keeps flashing to indicate that the device is working.

D6: The GSM module has just powered on. it flashes around two times every second. After

the device is successfully connected, it will flash slowly around once every two seconds.

D3: As long as the device receives the text message, D3 will flash several times.

Call Button LED: In order to facilitate the customer to observe the device, the LED combines

the functions of D3 and D6. After powered on or disconnected from the GSM net, Call button

LED will flashes around two times every second. After the device is successfully connected to the

GSM net, it will flash slowly around once every two seconds. Also during receive the an SMS

message, it will flash several times.

GSM-HOUSE INTERCOM UNIT

WAFER GSM-HOUSE PROGRAMMING

You can program the GSM-HOUSE with SMS commands using your phone. It is safe to do

so because in addition to the fact that other people may not know the number of the SIM inserted

in it, we also use a Password that makes it impossible for anybody who doesn't know it to access

the system by chance.

Remember that all commands must be CAPITAL LETTERS. Such as PWD not pwd, CAP

not Cap etc. Also Don't add spaces or any other character.

Some complicated Instructions,that cann’t be programmed by the phone SMS. That would

need to use the PC software to program and inquire the status of the terminal.

The following compand is used in the GSM-HOUSE :

#PWD: Password

#CAP: Change password

#WHL,SHL,PHL,QHL: White List (add or remove numbers)

#QUERY: Query the number

#MODE: Relay working mode

#GOT: Gate pulse time

#REPORT: Report status change

#REPLY: Reply enable or disable

#ALARM: Alarm information setting

#CSQ: Check Signal Quality

#STATUS: Check status

#DIAL: Add or remove Intercom Dial numbers

#OUT: Relay output control

Once an authorized user issue a command with an SMS, user will receive a confirmation

SMS with OK

SMS COMMAND LIST:

#PWD Password.

This command must always come first 6 digits as a password.

The initial password, when the device comes from the factory, is 123456.

In all the following examples will use 123456 as an example of password.

#CAP Change Password.

Use this command to change the password with a new one for your device

The #CAP command must be issued 2 times to be sure you don't digit a wrong one.

OF course it must be preceded by the old password.

For example, to change the password 123456 into the new password 333444 you need to send the

following SMS: #PWD123456#CAP333444#CAP333444

Acknowledge SMS: PWD SETUP OK

If you wrote correctly, or an Error message if you made a mistake.

If the old password is error,then conformation would be : Error Old Password

If you input two different new password,then reply would be : Error New Password,Please Check

the input again.

GSM-HOUSE INTERCOM UNIT

#GSM Intercom function and config command

1. Add the phone number for the inter calling

#PWD123456#DIAL01=180122333 and #PWD123456#DIAL02=181323344

Reply: DIAL01 SET TO 122333 OK Reply: DIAL02 SET TO 323344 OK

2. Inquiry the intercom calling number in the memory

#PWD123456#DIAL=ALL?

You will receive a Acknowledge with: DIAL IS 180122333:181323344:0000:0000:0000

3. During talking,user can press phone keypad number “1” or “*” to control the relay output1 and

press the number “2” or “#” to control the relay output2

The following is the function of GSM-KEY.

#WHL White List.

This is the command that you will use most. it is used to add or remove numbers that are enabled

to open the gate into the White List. You can add up to 200 numbers in the list. Every position

must be indicated in the command and we advise you to keep a list written somewhere to know

which numbers are in and in which position.

• To add a number, the syntax of the command is the following:

#PWD123456#WHL01=61143815

Acknowledge would be : WHL01 SET TO 61143815 OK

Where 01 is the position in the list and 61143815 is the number enabled.

Please note that it is possible to program up to a maximum of 10 digits for a number. If it has

more digits you should use the rightmost ones. For example, if your number is 33446665555 you

should program 3446665555. If your number appears as +85261143815 you should not program

the country code (+852). If your number has only 9 digits or less, it is not a problem. The

important thing is that you don't exceed 10 digits.

• To check which is the number in a place of the list:

#PWD123456#WHL01?

Acknowledge : WHL01 IS 61143815 OK

• To erase a number:

#PWD123456#WHL01=0000

(or you can write over it another number you wish to add)

Acknowledge : WHL01 SET TO 00000000

List All numbers in the List

#PWD123456#WHL=ALL? ( Only for PC COMMAND, Cann’t use the SMS to read back)

Acknowledge :

WHL01 IS xxx

WHL03 IS xxx

WHL08 IS xxx

……

Through the simple DIAL Command above, then already can use the INTERCOM

function. That is, by calling the button to call the set number

GSM-HOUSE INTERCOM UNIT

#SHL, #PHL, #QHL Special List.

Authorize the number by the time of the week

#PWD123456#SHL001=13564121668:1357(8:32-23:59)

Acknowledge : SHL001 SETUP TO 61143815:1357(8:32-23:59)

### SHL001 number would operate from 8:32 to 23:59 in Mon,Wen,Fri,Sun in every week.

Authorize the number by the date and time

#PWD123456#PHL001=13564121668:100324-101012(8:32-18:26)

Acknowledge : PHL002 SETUP TO 61143816: 100324-100812(8:32-18:26)

### PHL001 number would operate from 8:32 to 18:26 from Mar.24th to Oct.12

Authorize the number by the times of control

#PWD123456#QHL001=13564121668:12

Acknowledge : QHL003 SETUP TO 61143817:12

### QHL001 number would operate total 12 times,then would be expired.

• To check which is the number in a place of the list:

#PWD123456#SHL0001?

Acknowledge : SHL01 IS 61143815 OK

Or #PWD123456#PHL0001? #PWD123456#QHL0001?

• To erase a number:

#PWD123456#WHL01=0000

Or #PWD123456#PHL01=0000 #PWD123456#QHL01=0000

(or you can write over it another number you wish to add)

List All numbers in the List

#PWD123456#SHL=ALL? ( Only for PC COMMAND, Cann’t use the SMS to read back)

Acknowledge :

SHL01 IS XXX

SHL03 IS XXX

QHL08 IS XXX

……

#QUERY Query the phone number in the WHL list.

Query the phone number in the position of the WHL list,Special phone list or Alarm phone list

#PWD123456#QUERY=143535353

Acknowledge: QUERY RESULT: 143535353 AT WHL004

#ACM Safety control or free control mode setting.

#PWD123456#ACM=ON

Acknowledge: ACM SET TO ON

#PWD123456#ACM=OFF

Acknowledge: ACM SET TO OFF

ACM=OFF, Then any number can free control the device through the phone calling

ACM=ON, Then only the authorized number can control the device through the phone calling

GSM-HOUSE INTERCOM UNIT

#GOT Relay working output delay time. (Only for NO.1 Relay)

Setup the timer data with multiplier at millisecond or second or minutes.

#PWD123456#GOT5000:MILLISECOND

Acknowledge:DELAY TIME SET TO 5000 MS

#PWD123456#GOT500:SECOND

Acknowledge:DELAY TIME SET TO 0500 S

#PWD123456#GOT500:MINUTE

Acknowledge:DELAY TIME SET TO 0500 M

This command is useful in case you need to keep the Relay output working longer. The standard

time is 5 seconds (5000 ms). You can change it with the GOT command.

With the above command the delay time has been set to 5000 ms (5 seconds).

You can check what the current relay output delay time is with the command

#PWD123456#GOT?

Acknowledge: DELAY TIME IS 05000 MS

#ALARM Alarm setup

The Alarm01 is very important position,not only act as a alarm number,but also working as the REPORT phone

number, that means if you enable the REPORT function,then every report event happen,then would send the

REPORT SMS to this number

Setup the alarm phone number to receive the alarm SMS

#PWD123456#ALARM01=13818120592

Where 01 is the position in the list

Acknowledge: ALARM01 SET TO 61143815 OK

When the number is seted to 000000,that means delete the number in this position

List all numbers in the alarm phone list:

#PWD123456#ALARM=ALL?

Acknowledge: ALARM IS XXXXX:XXXX:XXXXXXX:0000:0000

(Will show total five numbers, if no effective number,that will be replaced with 0000 )

Alarm mode setup:

There are two alarm input ,you can set at PHONE or SMS

#PWD123456#ALARM-IN1=ON:PHONE:10,ALARM-IN2=OFF

Acknowledge: ALARM_IN1=ON:PHONE:10,ALARM_IN2=OFF OKAY

#PWD123456#ALARM-IN1=ON:SMS:300,ALARM-IN2=ON:PHONE:10

Acknowledge: ALARM_IN1=ON:SMS:300, ALARM_IN2=ON:PHONE:10

Set the content of the alarm message for alarm in1 and in2:

#PWD123456#UDI1:XXXXXX, UDI2:xxxxxx

Acknowledge: UDI1:XXXXXX, DI2:xxxxxx OKAY

(When the alarm occurs, the set alarm message will be sent)

Phone mode: When an alarm occurs, the preset number will be called

SMS mode: When an alarm occurs, Alarm message will be sent to the preset number.

GSM-HOUSE INTERCOM UNIT

Check the text set

#PWD123456#UDI?

Acknowledge: UDI1:ABC1, UDI2:ABC2

#REPORT Report the system status change

When setup to:

#PWD123456#REPORT=ON

Acknowledge: REPORT SET TO ON

Then any device status change would send the alarm SMS to Alarm01 number

#PWD123456#REPORT=OFF

Acknowledge: REPORT SET TO OFF

No report for the device status change

#PWD123456#REPORT?

You will receive the SMS reply: REPORT IS ON or REPORT IS OFF

Check the REPORT setting status

#CSQ Check GSM signal quality.

This command is useful to see what is the GSM network signal level your GSM-HOUSE is

receiving. It ranges from 0 to 32.You should have a signal above 12 to be sure of being able to

open the gate in any condition. Better if above 16. You should add an external antenna if this is

not the case.

#PWD123456#CSQ?

Acknowledge: CSQ IS 26

#MODE Relay Operation Mode SETUP

#PWD123456#MODE0

Acknowledge: RELAY SET TO MODE0

#PWD123456#MODE1

Acknowledge: RELAY SET TO MODE1

If set to MODE0,that is Momentary pulse and If Config to MODE1,that is Ratchet relay

#STATUS Check the config information of the terminal

#PWD123456#STATUS?

You will receive a Acknowledge SMS with:

ALARM1=OFF:SMS:12, ALARM2=OFF:SMS:10, GOT=05S, WHL=02, AIN1=HIGH,

AIN2=HIGH, BCPW=ON:70:80, CSQ=20, RELAY1=OFF, RELAY2=OFF

(ALARM1 and ALARM2 are the parameters setting, AIN1 and AIN2 are the input status,

BCPW is battery working and alarm status, Lower than 70% would alarm and Current has 80%

power )

#OUT Control the Relay Output on or off

#PWD123456#OUT1=ON or #PWD123456#OUT1=OFF

Acknowledge:OUT1 ON OK or OUT1 OFF OK

#PWD123456#OUT2=ON or #PWD123456#OUT1=OFF

Acknowledge: OUT2 ON OK or OUT2 OFF OK

GSM-HOUSE INTERCOM UNIT

Customized output control command TEXT:

#REPLY SMS reply OFF or ON

#PWD123456#REPLY=ON

Acknowledge:REPLY SET TO ON

When setup to ON,then Device will reply the customized command after Relay is toggled

#PWD123456#REPLY=OFF

Acknowledge: REPLY SET TO OFF

When setup to OFF,then Device will not reply the customized command after Relay is toggled

(This command is used to save the cost for the users who frequently control via SMS)

With this command, We can customize some simple and understandable Command to control. We

can also use some custom commands to allow some users to control SMS, but they don’t need to

know the management password of the device.

#PWD123456#OPEN1-TEXT#XXXX

#PWD123456#CLOSE1-TEXT#XXX

#PWD123456#RLY-TEXT1#XXX

If have the second output reply,then use the following command to config the second output

#PWD123456#OPEN2-TEXT#XXXX

#PWD123456#CLOSE2-TEXT#XXXX

#PWD123456#RLY-TEXT2#XXXX

Check the Customized command text:

#PWD123456#OUT1-TEXT?

Reply: OPEN1-TEXT=OPEN1,CLOSE1-TEXT=CLOSE1,TRIG1-TEXT=DIAN1

#PWD123456#OUT2-TEXT?

Reply: OPEN2-TEXT=OPEN2,CLOSE2-TEXT=CLOSE2,TRIG2-TEXT=DIAN2

For example,user send the command:

#PWD123456#CLOSE1-TEXT#G1 Close

Reply: CLOSE TEXT1 IS G1 Close

Then authorized users can use the simple SMS: “G1 Close”to switch on the output1 relay

#PWD123456#RLY-TEXT1#G1 Dian

Reply: RLY1-TEXT IS G1 Dian OKAY

Then can use the simple SMS: “G1 Dian”to trigger the output1 temporarily for GOT timer

Altri manuali per GSM-HOUSE

Indice

Altri manuali WAFER Sistema di interfono

WAFER

WAFER GSM-HOUSE Manuale utente

Manuali Sistema di interfono popolari di altre marche

Bticino

Bticino LINEA 3000 Manuale utente

MSI

MSI MSI-140 Manuale utente

golmar

golmar Stadio Plus Manuale utente

CyberData

CyberData 011211 series Manuale

Vidos

Vidos duo M1021 Manuale utente

Vimar

Vimar ELVOX 7539/E Manuale utente

SSS Siedle

SSS Siedle BTSV 850-03 Manuale utente

Dahua

Dahua VTO Series Manuale utente

Elvox

Elvox 5651 Manuale utente

Videx

Videx VIDEOKIT Series Manuale utente

Rocom

Rocom Doortello Business FW T2.05W2.04 Manuale utente

Viking

Viking E-35-EWP Manuale utente

Safeguard Supply

Safeguard Supply LRA-EX1000 Manuale utente

SSS Siedle

SSS Siedle BFCV 850 Series Manuale utente

GRD

GRD MAX V2 Manuale utente

Alecto

Alecto ADI-250 Manuale utente

Aiphone

Aiphone IE-8MD Manuale utente

Perel

Perel EDB4 Manuale utente