Wahlberg 255.700 Manuale utente
WWW.WAHLBERG.DK
JENS JUULS VEJ 1
TELEPHONE: +45 86 18 14 20 8260 VIBY
EMAIL: [email protected]
DENMARK
AC Motor Controller Series
Item No. 255.700 and 255.701
User Manual
AC Motor Controller 550 W No. (255.700)
AC Motor Controller 3000 W No. (255.701)
255.805.001 2 Date: 2021-03-12
Safety Information
WARNING! Read this manual before installing, powering or servicing the product; follow the
safety precautions listed below and observe all warnings in this manual and printed on the
product. If you have questions about how to operate the product, please contact you Wahlberg
Motion Design supplier or Wahlberg Motion Design.
The following symbols identify important safety information on the product and in this manual.
DANGER!
Safety hazard
WARNING!
Moving parts
can crush and
cut
DANGER!
Risk of
electric shock
WARNING!
Risk of fire
WARNING!
Hot surface
WARNING!
See manual
GENERAL PRECAUTIONS
This product is for professional use and presents risks for sever injury or death.
Always warm-up electronic equipment to room temperature before applying power.
Isolate the product from power immediately if defective or showing signs of overload.
Do not reapply power until repairs have been completed.
Do not modify the product in any way not described in this manual.
Refer any service operation not described in this manual to a qualified technician.
Install only genuine Wahlberg parts.
PROTECTION FROM INJURY
Fasten the product securely to a fixed surface, rig, or structure as described in this
manual.
Ensure that any supporting hardware can hold at least 10 times the weight of all the
devices they support.
Block access below the work area whenever installing or servicing the product.
Do not use the product to lift people or animals and do not exceed the load limits.
Do not use the product to lift anything over the head of people.
When the product is installed and may not be used for some time, inspections and
maintenance according to this manual shall always be followed.
PROTECTION FROM ELECTRIC SHOCK
Do not expose the product to rain or moisture.
Use an AC power source with overload and ground(earth)-fault protection.
Disconnect from AC power before servicing.
PROTECTION FROM BURNS AND FIRE
Do not operate the product if the ambient temperature (Ta) exceeds 40° C (104° F).
The exterior of the product becomes warm during use. Avoid contact by persons and
materials. Allow the product to cool for at least 10 minutes before handling.
DISPOSING OF THIS PRODUCT
Wahlberg Motion Design products are supplied in compliance with Directive 2012/19/EU of the
European Parliament and of the Council of the European Union on WEEE (Waste Electrical and
Electronic Equipment), including amendments where applicable. Help preserve the
environment! Ensure that this product is recycled at the end of its life. Your supplier can give
details of local arrangements for the disposal.
255.805.001 3 Date: 2021-03-12
Index
SAFETY INFORMATION 2
INDEX 3
TECHNICAL SPECIFICATIONS 4
DRAWING 5
INTRODUCTION 6
PACKAGE CONTENT ...................................................................................................................................... 6
DESCRIPTION............................................................................................................................................... 6
AREA OF USE ............................................................................................................................................... 7
USING FOR THE FIRST TIME ............................................................................................................................ 7
TRANSPORT ................................................................................................................................................ 7
PHYSICAL INSTALLATION 8
FASTENING THE PRODUCT TO A FLAT SURFACE................................................................................................... 8
MOUNTING THE PRODUCT ON A TRUSS (TUBE/PIPE) .......................................................................................... 8
CONNECTIONS ............................................................................................................................................. 9
AC POWER 11
VOLTAGE .................................................................................................................................................. 11
POWER CABLES AND POWER PLUG ................................................................................................................ 11
INSTALLING A POWER INPUT CONNECTOR ON A POWER CABLE ........................................................................... 11
DATA LINK 12
TIPS FOR RELIABLE DATA TRANSMISSION ........................................................................................................ 12
CONNECTING THE DATA LINK ........................................................................................................................ 12
EMERGENCY STOP (OPTIONAL) 13
ENCODER (OPTIONAL) 13
HARD LIMITS 14
AUXILIARY (FUTURE USE) 14
MOTOR 15
INSTALLING A MOTOR OUTPUT CONNECTOR ON A MOTOR CABLE ........................................................................ 15
BRAKE (OPTIONAL) 15
INSTALLING A BRAKE OUTPUT CONNECTOR ON A BRAKE CABLE ........................................................................... 15
SETUP 16
POWERING-UP .......................................................................................................................................... 16
MENU SETTING .......................................................................................................................................... 17
MENU STRUCTURE ..................................................................................................................................... 18
ADJUSTABLE PARAMETERS ........................................................................................................................... 21
DETAILED EXPLANATION OF PARAMETERS ....................................................................................................... 21
MODE SETTING .......................................................................................................................................... 25
DMX CHANNEL OVERVIEW .......................................................................................................................... 26
GETTING STARTED WITH THE AC MOTOR CONTROLLER .................................................................................... 28
LED FUNCTIONS ........................................................................................................................................ 30
ERROR AND ERROR CODES ........................................................................................................................... 30
SERVICE AND MAINTENANCE 31
SPARE PARTS ............................................................................................................................................. 31
ON-SITE SERVICE ........................................................................................................................................ 31
MAINTENANCE PLAN .................................................................................................................................. 31
CHECKLIST ................................................................................................................................................ 32
APPENDIX 1 – DIMENSIONS 33
APPENDIX 2 – POWER & BRAKE CONNECTOR 35
APPENDIX 3 – MOTOR CONNECTOR 37
APPENDIX 4 – BLOCK DIAGRAM 38
AC MOTOR CONTROLLER – CHEAT SHEET 40
255.805.001 4 Date: 2021-03-12
Technical specifications
Model: AC Motor Controller Series
Item no.: 255.700 (550 W) and 255.701 (3000 W)
Dimensions: (L×W×H)
550 W (255.700) 280 x 162 x 137 mm (11 x 6.4 x 5.4 in)
3000 W (255.701) 400 x 207 x 138 mm (15.7 x 8.1 x 5.4 in)
Power supply:
550 W (255.700) 208-240 VAC 50/60 Hz (1P+N+PE)
3000 W (255.701) 380-415 VAC 50/60Hz (3P+N+PE)
Power consumption:
550 W (255.700) 600 W (2,9-2,5A)
3000 W (255.701) 3050 W (9,6A)
Power inlet:
550 W (255.700) Neutrik powerCON TRUE1 NAC3PX (F/M)
3000 W (255.701) CEE 16A (M)
DMX control signal: DMX 512 1990 + DMX512A / 4, 6 or 10 channel modes.
DMX connection: 5 pole XLR (F/M)
Other control inputs: 3-4-5 pole XLR (F) Encoder, Emergency, Limit and AUX
Motor output: Harting HAN A 3P (F/M included)
Brake Connection: Neutrik powerCON TURE1 NAC3FPX (F)
Speed: 0-5000 rpm (depending on motor and gear)
Noise emission: 46 dB @ 1m (3.3 ft)
Ambient temperature: 5-40°C (41-104°F)
Weight:
550 W (255.700) 3 kg (6.6 lb)
3000 W (255.701) 5 kg (11 lb)
Mounting: 2xø12,5mm (0.49 in) and 4xø6,5mm (0.26 in) hole
Motor:
Rating:
550 W (255.700) 208-240VAC/Max. 0.75HP/2.8A/550 W
3000 W (255.701) 380-415VAC/Max. 4HP/7.6A/3000 W
Type: Connect 3 phase motor (∆/Υ depending on motor rating)
Brake: Connect 1 phase brake 220-240VAC/Max. 3.0A
Duty-cycle: 100%
255.805.001 5 Date: 2021-03-12
Drawing
AC Motor Controller 550 W (255.700)
More detailed drawings can be found in Appendix 1 on page 33
AC Motor Controller 3000 W (255.701)
More detailed drawings can be found in Appendix 1 on page 33.
255.805.001 6 Date: 2021-03-12
Introduction
Thank you for selecting the AC Motor Controller Series, a DMX controlled AC frequency inverter
from Wahlberg Motion Design. Before using the product for the first time, please read this
manual carefully. Failure in handling can cause injury of persons and/or damage the product.
Package content
1× AC Motor Controller
1× powerCon TRUE1 female plug NAC3FX-W for power cable (255.700/550 W only)
1x Harting HAN A 3P male connector for motor cable with PG11 cable gland (metal)
1x User Manual
1x Cheat sheet
Description
The product is for stage use, mainly for use in theatres, shows, and concerts. It controls 3 phase
AC motors (not included) to move props and small set pieces or similar in and out of the stage
sphere with a motor rating up to 4HP. Multiple products may easily be connected as a chain,
allowing for advanced and creative ways of making dynamic movements.
The product is controlled through 4, 6 or 10 DMX channels from a lighting desk, where the
position and speed can be changed live or pre-programmed as wished. Through the lighting desk
the top and bottom positions can also be set. However, several hardware options are available
to meet the specific application e.g. using an external encoder, applying external switches to
limit the movement, and using an AC motor brake when the gear is not dynamic self-locking with
the applied load.
Safety functions
The control system ensures that the motor is only powered when:
The DMX signal is reliable.
The motor enable channel is in the operation range.
The speed control channel is on (more than 0%).
The motor is instructed to move.
No overload.
The Emergency input is active and enabled
The product should only be operated by an experienced lighting-desk-operator. The lighting desk
must be programmed according to the manual, so the unit will stop when the speed is put to 0
%. It is also possible for the user to stop the product by disconnecting the mains power, provided
a brake is installed correctly or the gear is dynamic self-locking. After Power interruption the
motor enable channel shall be pullet to 0% and back to the enable range before the product can
function again.
255.805.001 7 Date: 2021-03-12
Area of use
For indoor use only!
WARNING! To reduce the risk of electric shock or injury: use indoors only
WARNING! To reduce the risk of electric shock, do not expose to rain: store indoors!
The product is intended for indoor use only. It is designed for controlling a 3 phase AC motor as
stated in "Technical Data". Any other use of the product may result in a risk of injury of persons
or equipment damage.
Exceeding the inverter load rating may cause failure of the equipment.
Do not modify the product. For any modification contact Wahlberg Motion Design.
It is the customers' responsibility that any local restrictions concerning the use are fulfilled.
Using for the first time
Important! The product must be protected from environmental factors such as physical shocks
and vibration during transportation and storage.
WARNING! Read “Safety Information” on page 2 before installing, powering, operating, or
servicing the product. Before applying power to the unit:
Check the Wahlberg Motion Design website at www.wahlberg.dk for the most recent
documentation and technical information about the product. Wahlberg user manual revisions
are identified by the revision number in the bottom of each page.
Carefully review the “Safety Instructions” on page 2.
Check that the local AC mains power source is within the voltage and frequency ranges
specified on the product.
See “Power cables and power plug” on page 11. Install a Neutrik powerCON TRUE1 NAC3FX-W-
TOP (255.700) or the CEE 16A (255.701) power input connector on a suitable power cable. If
using the power from a mains power outlet, install a suitable power plug on the power cable.
Transport
Important! The product must be protected from environmental factors such as physical shocks
and vibration during transportation.
Use only the original packaging or flight case for protecting the product during transport.
Contact Wahlberg for enquiries regarding flight cases.
255.805.001 8 Date: 2021-03-12
Physical installation
WARNING! The product must be either fastened to a flat surface such as a roof or clamped to
a truss or similar structure. Do not apply power if it is not securely fastened.
WARNING! The supporting surface must be hard and flat. Fasten the product securely.
WARNING! When the unit is installed in a location where it may cause injury or damage if it
falls, install a secondary suspension such a BGV C1/DGUV 17 safety cable using one of the
12.5mm (0.49 in) holes and fasten it securely around the truss/pipe.
Fastening the product to a flat surface
The product can be fastened to flat surface such as a roof. Check that the surface can support at
least 10 times the weight of all products and equipment to be installed on it, and that the
installation respects all locally applicable regulations.
Mounting the product on a truss (tube/pipe)
The unit can be clamped to a truss or similar rigging structure.
To clamp a product to a truss (tube/pipe):
1. Check that the rigging clamp is undamaged and that the rigging structure can support at
least 10 times the combined weight of all products and equipment to be installed on it.
2. Use the suitable rigging clamp or contact Wahlberg Motion Design for a replacement.
3. Fasten the clamp to the unit with the supplied M12 bolts, nuts, and washers in the hole of
the mounting clamp on the unit.
4. Block access under the work area. Working from a stable platform, hang the product on
the truss with the fabric downwards. Tighten the rigging clamp.
5. Install a suitable safety cable when the product is hanging over-head.
Safety Cable
Half
-
coupler
255.805.001 9 Date: 2021-03-12
Connections
Model: 550 W (255.700)
The below shows the possible connections to the AC motor controller and in the following
sections each of the connection will be explained in detail.
Quick overview of the pinout as shown on the front panel. For further guidance see also
Appendix 4 – Block Diagram on page 38.
255.805.001 10 Date: 2021-03-12
Model: 3000 W (255.701)
The below shows the possible connections to the AC motor controller and in the following
sections each of the connection will be explained in detail.
Quick overview of the pinout as shown on the front panel. For further guidance see also
Appendix 4 – Block Diagram on page 38.
Questo manuale è adatto per i seguenti modelli
1
Indice
