Wali PTT008 Manuale utente

INSTALLATION MANUAL

PTT008

Monitor Stand Riser

20kg/44lbs

RATED

1-844-SATTLER (18447288537)

[email protected]

www.walielectric.com

Attach the Nut E to the hole on Board C as the image shown.

Caution: Please make sure the arrow on Nut E is pointing upright towards the edge of Board C as the image shown.

Place Support Stand B on a flat surface, insert the Bolt D to the center hole on Support Stand B and tighten

with a screwdriver. (Screwdriver not included)

Caution: Please make sure the Bolt D is vertically straight at an 90° angle to the surface of Support Stand B as

the image shown.

Insert the Wood Dowel Pin F to the side hole on Support Stand B .

Supplied Parts List

Step 1

Step 2

Board

A (x1)

Support Stand

B (x2)

Bolt

D (x6)

Board

C (x1)

Nut

E (x6)

Wood Dowel Pin

F (x4)

Cellphone Holder

H (x1)

Sticker

I (x6)

Anti-skid Pad

G (x4)

Caution: Frequently assembling and disassembling may cause damage to the wood board.

Support Stand surface

90° Angle

Bolt

Insert Board C to the Bolt D and Wood Dowel Pin F on Support Stand B and tighten the Nut E clockwise

to fasten for stability. (Screwdriver not included)

Step 3

Board surface

Place Board A on a flat surface with bottom upward, insert the Bolt D to the hole on Board A and tighten

with a screwdriver. (Screwdriver not included)

Caution: Please make sure the Bolt D is vertically straight at an 90° angle to the surface of Board A as the image shown.

Attach the Nut E to the hole on Support Stand B as the image shown.

Caution: Please make sure the arrow on the nut is pointing upright towards the hole on the Support Stand B as the image

shown.

Step 4

Step 5

90° Angle

Bolt

Tighten the Nut E clockwise to fasten for stability. (Screwdriver not included)

Insert the assembled support stand to the Bolt D on Board A .

Step 7

Step 6

Tear off the Anti-Skid Pad G and sticker I , attach it to the designated position as the image shown.

Insert the Cellphone Holder H to the designated position on Board A .

Notice: The Cellphone Holder is removable. Push it from the back of the Board A to remove it if necessary.

Optional Step

Step 8

Manuali Rack e supporto popolari di altre marche

Salamander

Salamander Acadia AC/W/L400/WH Manuale utente

Fohhn

Fohhn VAT-09 Guida utente

ricoo

ricoo FS0522 Manuale utente

AMSOIL

AMSOIL BMK-22 Guida rapida

Kargo Master

Kargo Master 48220 Manuale utente

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuale utente

ricoo

ricoo S1222 Manuale utente

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuale utente

VidaBox

VidaBox VB MNT FFS2 Manuale utente

Welch Allyn

Welch Allyn 48960 Manuale utente

Arkon

Arkon CM035-ST-2 Manuale utente

PROEL

PROEL PLWIN60C Manuale utente

Agilent Technologies

Agilent Technologies E2609B Manuale utente

Mustang

Mustang MV-ARM4 Manuale utente

Mounting Solutions

Mounting Solutions WRM-320 Manuale utente

Pyle

Pyle PMKSPAD1 Manuale utente

ShelterIt

ShelterIt 21208 Manuale utente

SPL

SPL RackPack?4 1040 Manuale utente