Wallenstein 3036A030 Manuale utente
Rev Jun-2021
Tieback Mount
INSTALLATION INSTRUCTIONS
3036A030
Introduction 3036A030
Tieback Mount
2
Introduction
This tieback mount is designed to work with a Wallenstein
backhoe. The backhoe must have an SQ500 universal quick-
attach plate installed (not included).
Wallenstein backhoes are designed to work with a wide variety
of skid steers. This tieback mount provides a method to attach
and detach a Wallenstein backhoe to a New Holland® L223 skid
steer.
The tieback mount kit includes parts and hardware
that are shown under Tieback Mount Parts on page
4. Make sure that all the parts are present and
not damaged from shipping.
Following are two reasons that a skid steer tieback mount is
required:
• To avoid inadvertent movement of the skid steer controls
while a person is on the backhoe.
• To reduce pressure spikes in the hydraulic lines and prevent
damage to the hydraulic system.
Some of the illustrations in this instruction are general; however,
important features are detailed to assist with installation.
Before using, installing, or maintaining this
equipment, read and understand the safety,
operation, and maintenance information in the
backhoe Operator's Manual.
If you have questions or require assistance, contact your local
dealer, the distributor, or Wallenstein Equipment.
IMPORTANT! Installation may include metric or imperial
fasteners. See the bolt head markings to identify the bolt
type.
Metric
Imperial
Wallenstein Equipment Inc. • © 2021. All rights reserved.
No part of this work may be copied, reproduced, replaced,
distributed, published, displayed, modified, or transferred in
any form or by any means except with the prior permission of
Wallenstein Equipment Inc.
Table of Contents
Introduction.................................................................2
Safety...........................................................................3
Safety Alert Symbol .........................................................3
Signal Words ...................................................................3
Safety Information............................................................3
Tieback Mounts ..........................................................4
Tieback Mount Parts........................................................4
Tools Required.................................................................5
Install the Tieback Mount.................................................5
Connect a Quick-Attach Plate..........................................7
SQ500 Universal Quick-Attach Plate ........................9
SQ500 Universal Quick-Attach Plate Parts .....................9
Install a Quick-Attach Plate on a Backhoe.....................10
Install the Toplink Assemblies ........................................ 11
Adjust the Quick-Attach Plate Position ..........................13
Common Bolt Torque Values...................................15
www.wallensteinequipment.com
Orientation
IMPORTANT! When describing directions in this instruction,
left-hand (LH) side, right-hand (RH) side, back, and front
are determined when sitting in the skid steer driver's seat,
facing the direction of forward (FWD) travel.
FWD
01681
Safety 3036A030
Tieback Mount
3
Safety
Safety Alert Symbol
This Safety Alert Symbol means:
ATTENTION! BE ALERT!
YOUR SAFETY IS INVOLVED!
The Safety Alert Symbol identifies important safety messages
on the machine and in this instruction. This symbol means
be alert to the possibility of personal injury or death. Follow
instructions provided.
Signal Words
The signal words DANGER, WARNING and CAUTION determine
the seriousness level of the warning messages in this manual.
The appropriate signal word for each message in this manual
has been selected using the following guidelines:
DANGER –
Indicates an imminently hazardous situation that, if not avoided,
will result in death or serious injury. This signal word is to be
limited to the most extreme situations typically for machine
components which, for functional purposes, cannot be shielded.
WARNING –
Indicates a potentially hazardous situation that, if not avoided,
could result in death or serious injury, and includes hazards that
are exposed when shields are removed. It may also be used to
alert against unsafe practices.
CAUTION –
Indicates a potentially hazardous situation that, if not avoided,
may result in minor or moderate injury. It may also be used to
alert against unsafe practices.
IMPORTANT – To avoid confusing equipment protection
with personal safety messages, the signal word IMPORTANT
indicates a situation that if not avoided, could result in damage
to property or the machine.
Provides additional information that is helpful.
Safety Information
WARNING!
Avoid the risk of personal injury or machine
damage! Read the backhoe Operator’s Manual
before using this equipment. Carefully read all
safety messages in the manual and follow all
safety signs on the machine.
WARNING!
Before installing this equipment:
• Position the backhoe and skid steer on dry,
level ground.
• Make sure the area around them is clear and
free of debris.
• Turn o the skid steer engine, apply the
parking brake, and remove the key.
Tieback Mounts 3036A030
Tieback Mount
4
Tieback Mounts
Install the two tieback mounts on the skid steer.
Tieback Mount Parts
1
2
3
4
5
Fig. 1 – Tieback Mount Parts
Item Part
Number
Description Quantity
1 Z771715 Hex bolt, M12 x 1.75 x
55 mm
2
2 Not included1Washer 2
3 Not included1Lock nut 2
4 3036W031 Tieback mount, RH 1
5 3036W031H Tieback mount, LH 1
1 Use the hardware that is on the skid steer.
Tieback Mounts 3036A030
Tieback Mount
5
Tools Required
• Basic shop tools.
• One socket wrench with a 19 mm socket.
• One calibrated torque wrench with a 19 mm socket.
Install the Tieback Mount
Tieback mount item numbers are in brackets and defined under
Tieback Mount Parts on page 4.
Step 1
Place the skid steer in a safe condition:
a. Stop the skid steer on a dry, level surface.
b. Lower the coupler to the ground.
c. Apply the parking brake.
d. Turn off the engine.
e. Remove the key.
f. Activate the hydraulic controls to remove pressure from
the hydraulic system.
Step 2
Complete the following for each of the two tieback mounts
(only the RH side is shown):
a. Remove the lock nut (3) from the skid steer bolt.
b. Remove the hex bolt and washer (2) from the front of the
skid steer.
c. Place the tieback mount (4 or 5) over the skid steer bolt.
Align the center-plate hole with the bolt hole in the skid
steer.
d. Install the lock nut on the skid steer bolt.
e. Install a hex bolt (1) through the washer, through the
tieback mount, and into the skid steer.
Tieback Mounts 3036A030
Tieback Mount
7
Step 1
Align the two toplink (5) assemblies with the tieback-plate
connections.
The toplink assemblies must be perpendicular to the tieback-
plate connections. If required, move the toplink assembly
location on the main-base weldment (9). For instructions, see
Install the Toplink Assemblies on page 11.
Step 2
Complete the following for each toplink (only the LH side is
shown):
a. Align the toplink (5) with the tieback-mount connection
holes.
b. Insert a hitch pin (7) through the toplink and tieback-
mount connection.
c. Insert a lynch pin (6) through the hitch pin.
The backhoe must have an SQ500 universal quick-attach plate
installed (not included). For instructions, see SQ500 Universal
Quick-Attach Plate on page 9.
Quick-attach plate item numbers are in brackets and defined
under SQ500 Universal Quick-Attach Plate Parts on page 9.
Connect a Quick-Attach Plate
SQ500 Universal Quick-Attach Plate 3036A030
Tieback Mount
9
SQ500 Universal Quick-Attach Plate
An SQ500 universal quick-attach plate is not included
with the tieback mount.
If you have questions or would like more information,
contact your local dealer, the distributor, or Wallenstein
Equipment.
SQ500 Universal Quick-Attach Plate Parts
1
2
12
14
13
4
5
6
7
3
8
9
11
10
01673
Fig. 2 – SQ500 Universal Quick-Attach Plate Parts
Item Part Number Description Quantity
1 Z51919 Flat-face, FP08 x MISO16028 1
2 Z51920 Flat-face FP08 x FISO16028 1
3 3035L109 Clevis, turnbuckle 2
4 Z71540 Hex Bolt 1/2 NC x 4" 4
5 Z11501 Toplink, Cat 0 x 10–1/2" x 16" 2
6 Z12110 Lynch Pin, 3/16" 4
7 Z11232 Hitch Pin, 5/8" x 4–1/4" 4
Item Part Number Description Quantity
8 Z72251 Hex lock nut 1/2" NC 4
9 3031W101 Weldment, main base 1
10 Z14181 Roll pin 5/16" x 1–1/2" 2
11 3031M101 Shaft, lower pivot link 1
12 3031W102 Weldment, pivot backhoe 1
13 Z72271 Hex lock nut 3/4" NC 2
14 Z71720 Hex bolt, 3/4" NC x 2" 2
SQ500 Universal Quick-Attach Plate 3036A030
Tieback Mount
10
01674
Install a Quick-Attach Plate on a Backhoe
IMPORTANT! Stabilize the backhoe to prevent movement
during installation.
Quick-attach plate item numbers are in brackets and defined
under SQ500 Universal Quick-Attach Plate Parts on page 9.
For clarity, some backhoe parts are not shown in the following
image.
Tools Required
• Basic shop tools.
• One calibrated torque wrench with 1–1/16" socket.
• One 1–1/16" open-end wrench.
• One socket wrench with 1–1/16" socket.
Step 1
Align the pivot-backhoe weldment (12) with the backhoe main
frame (for information about the location of backhoe parts, see
the backhoe Operator's Manual).
Step 2
Install the eight 5/8" NC bolts (not shown) and lock nuts (not
shown); four on each side.
Step 3
Use a calibrated torque wrench to tighten the eight lock nuts to
160 lbf•ft (215 N•m).
Step 4
Install the two turnbuckle clevises (3) and toplinks (5). For
instructions, see Install the Toplink Assemblies on page 11.
Fig. 3 – Universal Quick-Attach Plate Installation
Indice
Altri manuali Wallenstein Rack e supporto
