Walter MANOTOP Manuale utente
NM MANOTOP 01/2012
15
Total track length TL
Track/trackdistance
TT
Left
Right
Right overlap
MAX. 100 mm
Opposite
side
Storage
side
Storage side overlap
MAX. 400 mm
Left overlap
MAX. 100 MM
Opposite side
overlap
MAX. 300 mm
3D view
To lay the tracks, follow these steps:
- Mark out a line at distance L from the edge of the pool L = P1 – 15 mm
P1 MAX. 100 mm
I. POSITION OF TRACKS
SUPPLIES REQUIRED:
-TOP track
-Track fastening screw kit (ZD 200009)
-TOP profile connector (ZU 100006)
Line marked
P1
L
Leftoverlap
- Mark a second line at L = TT – 30 mm from the first one.
(TT: track / track distance, as defined in the measurements document)
- Measure the right-hand overlap to check it MAX. 100 mm
P2
-Place the tracks along the line, taking care to respect the L1 measurement,
namely 200 mm, and L2 100 mm.
WARNING: The tracks must be perfectly parallel
P2
P1
L2
L1 = 200 mm
TT
Line marked
L2 = 100 mm
D1=Diagonal 1
D2 =Diagonal2
To check, measure the diagonals. D1 must be equal to D2 with a max. difference
of 10 mm
- Assembly the guide and track by slotting the two pieces together and fastening with
the assembly screw provided.
II. PLACING THE LEADER GUIDES:
Assembly
screw
- A screw protrudes underneath the entry guide, so drill a hole in the slab
Do not forget to fit the junction pieces when fitting track sections end to end.
Tracks
Junction piece
II. JUNCTION PIECE:
IV. FASTENING THE TRACKS:
- Before drilling the holes, check the position
of the tracks along the line you marked out.
- Drill all the 8 mm diameter holes, put in the plugs and the
5.5x50 screws and tighten.
- Place the end cap on the end of the track.
Ø8
I. INSTALLING THE POSTS:
1.1. Rule to be respected when installing the posts:
- Mark out the position of the post with the measurements and as shown below
200 mm
160 mm 160 mm
400 mm max.
NB: This sketch shows an assembly with the winding wheel on the left.
For an assembly with the wheel on the right, reverse the posts.
1.2. Fixing the posts:
Once you have marked out the position, pre-assemble the roller.
Serrated lockwasher M8 Washer Ø 8
Rubber shim
Screw H M8x60
Tighten the H M8 screws until the rubber shims come into contact with each other. Then put
on 1 retainer ring before fitting onto the post
Repeat the procedure for the other side and do not forget to put on the winding shaft
centering ring.
When all the parts are assembled (the 2 end shafts and the winding tube), slide the coupling
onto the shaft on the winding mechanism side (see sketch above).
Retainer ring WINDING TUBE
II. FITTING THE ASSEMBLY:
Rule to be respected when fitting the assembly:
- In order to ensure the coaxiality of the assembly, position the winding tube
in the posts (no need to worry about the position of the tube in the posts for
the moment, as this will be adjusted later).
- Line up the posts with the marks on the ground
200 mm
160 mm 160 mm
400 mm max.
- Drill the 4 holes for the base through the base using an 8 mm drill bit
- Fasten with the four 5.5x50 screws and the 8 mm plugs
- The tube must be centered in relation to the tracks so that the cover winds
correctly onto the winding tube
- If you have followed the previous procedure correctly, you will be able to
position the tube 180 mm from the post on the opposite side to the drive
side initially
TT
~180 mm
- Fit the second ring inside the post and bring the external ring up against
the post and block it without forcing it
TT – 30 mm
= =
Indice
Altri manuali Walter Attrezzatura di illuminazione
Walter
Walter Walu Cool Manuale utente
Walter
Walter Junior Silver Manuale utente
Walter
Walter WALU STAR AIR Manuale del proprietario
Walter
Walter Walu Roll Banc Mobil Solario Manuale utente
Walter
Walter WaluCover Manuale utente
Walter
Walter WALU POOL ADVANTAGE Manuale utente
Walter
Walter AXIO Manuale utente
