Washify MOXA Manuale di istruzioni

Altri manuali per MOXA

1

Altri manuali Washify Controllori

Washify

Washify MOXA Manuale di istruzioni

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente

Installing Washify Controller Integration

Table of Contents.

1. Mounting the Enclosure

Step 1. Metal Fins

Step 2. Lag Fins to the Wall

Step 3. Verify Mounting

2. Providing Power and Network

Step 1. Locate and Identify wire fittings

Step 2. Running Network/Cat Cable connection

Step 3. Tighten Network/Cat Cable fitting

Step 4. Terminate Network/Cat Cable

Step 5. Test Network/Cat cable

Step 6. Connecting Network Cable to Moxa

Step 7. Run power wires

Step 8. Insert power wires

3. Wiring to controller

Step 1. Run cables from 16 Keypad Push Button Station to Integration enclosure

Step 2. Insert Common Jumper strip

Step 3. Follow diagram to connect relays to 16 Keypad Push Button Station

Step 4. Connecting Adapter to ICS 16 Button Keypad

Step 5. Controller Code assignment

1.Mounting the Enclosure

This section will describe the process of mounting the Controller Integration enclosure in your car

wash.

The First task is to find a suitable location. The following conditions must be met:

1. Easy access to 120VAC power to provide power for the enclosure.

2. Less than 100ft ethernet cable length between the enclosure and the Washify network hub. Avoid

running the ethernet cable near equipment that causes large levels or electrical noise (Electric

Motors, Electric Pumps, Power Inverters).

3. Less than 30ft of integration wiring between the enclosure and the ICS PBS. Avoid running the

ethernet cable near equipment that causes large levels or electrical noise (Electric Motors, Electric

Pumps, Power Inverters).

After choosing a suitable location. You will need to mount the enclosure. Inside the enclosure are 4

metal stands. These stands screw into the back of the box and provide an elevation off of the wall.

They also allow you to mount the enclosure without needing to drill holes into the back of the

enclosure. Mounting screws and method of mounting is left to the discretion of the installer.

Step 1.1. Mount Metal mounting fins onto the enclosure with provided bolts

Step 1.2. Mount Box to wall using lag bolts or required hardware for wall type.

Step 1.3. Verify Mounting is flush and will not fall

2.Providing power and a network connection

Step 2.1. Locate and identify fittings for power and network cable (take note of integration wiring

fitting as it will be needed later)

Step 2.2. Run a Cat5e or Cat6 cable from the network hub to the Integration box. Do not place the

RJ45 plug on the cat cable until it has been run inside the fitting.

Remove the cap of the fitting, run the cable through the cap then into the enclosure. Leave enough

slack to be able to work comfortably crimping the RJ45 plug on the cable.

Step 2. 3. Once the cable is inside the box, screw the cap back on the fitting and tighten.

Step 2.4. Terminate the Cat cable into a RJ45 end. Make sure to follow T568B standard on both ends

of the Cat cable. You can find the standard in the image below.

Step 2.5. If a cable tester is available, test the cable to verify all pins are conducting properly.

Step 2.6. Insert the crimped RJ45 end into Port 1 on the Moxa box shown below