Watercool HEATKILLER GPU-X2 4870 Manuale utente

Assembly instructions

HEATKILLER® GPU-X²4870/4890

The HEATKILLER® GPU-X² 4870/4890 guarantees the highest degree of cooling power. The unique

design ensures maximum performance on a level with current high-end CPU coolers. Extremely fine

microstructures cool both graphic processors very effectively. All other relevant components (e.g.

RAM, NVIO, VRM) are also cooled.

The top and bottom parts consist of highly pure electrolyte copper.

Dimensions (LxWxH):

143.0 x 119.0 x 12.5 mm

Weight

650 g

Material (base/centre part)

CU/CU

Material (inlay)

stainless steel

Connections

G ¼ inch

Temperature-resistant up to

80°C

Compatible with

ATI 4870, ATI 4890 (reference design)

Notice: A coloured installation manual in PDF format is available in the service section of our

homepage at www.watercool.de

Attention: Conversion at your own risk. Non-observance of the installation instructions may damage

the graphic board. Watercool will assume no liability for damage to the hardware. In case of

uncertainty, please commission an expert with the conversion or use our conversion service.

Dismantling the original cooler may lead to the loss of the manufacturer's warranty. In case of

uncertainty, please contact the manufacturer of the graphic board.

Preparing the graphic board

Remove the original cooling element and all remainders of the thermal pads.

Now fit each of the four M 3 x 8 screws in the GPU area with a washer and press them through the

card from the GPU area below. The red spacers are subsequently positioned from above. It is easier

to screw the screws into the spacers than to press them into them.

Then place the pre-cut pads onto the graphic board, as shown below.

Evenly apply thermal grease to the GPU area.

Installation of the cooler

Then place the cooler onto the prepared graphic board and turn it over, including the board. Screw the

screws in the GPU area in slightly – crosswise and uniformly.

PLEASE NOTE: Do not tighten screws yet!

Now screw the two M3 x 5 mm screws into the cooler, in the area of the voltage converters, using one

washer each. Do not tighten these screws either.

Once all screws of the cooler have been positioned, these can be tightened slightly. To do this,

carefully tighten the screws in the GPU area crosswise. Then tighten the screws in the voltage

converter and NVIO areas slightly.

Installation and leak test

After the installation, a check and test run must be performed! The coolers are constructed on the

reference design; still, all sections of the board have to be checked for possible contact to the cooler.

In addition, the contact of the GPU to the cooler must be checked along with the bending of the board.

A slight bending of the board is normal.

A leak test should preferably be performed outside of the computer. If this is not possible, the

hardware may not be turned on during the test run!

Once all of the cooler elements were tested, the computer can be put into operation. Check the

temperature of the GPU immediately after the start!

General information

The HEATKILLER® GPU-X² 4870/4890 has a defined input/output. The port on the left (pointing

towards the slot cover) is the input. The output is located on the right, and the connections can be

installed either on the top or the bottom.

We recommend using demineralised or deionised water (distilled water) as cooling medium. To

prevent the build-up of algae, use common citric acid, which reliably prevents the spread of algae.

HEATKILLER® are manufactured by

Please send your questions, suggestions or

criticism to the following address:

Watercool e.K

Warendorfer Strasse 20

D-17192 Waren

GERMANY

Tel: (+0049) 03991-187601

Fax: (+0049) 03991-187602

E-Mail: info@watercool.de

Web: www.watercool.de

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Watercool Hardware per computer

Watercool

Watercool HEATKILLER IV Pro Manuale utente

Watercool

Watercool HEATKILLER IV Manuale utente

Watercool

Watercool HEATKILLER IV VGA Series Manuale utente

Watercool

Watercool HEATKILLER V VGA Series Manuale utente

Watercool

Watercool HEATKILLER V VGA Series Manuale utente

Watercool

Watercool Heatkiller GPU-X2 Series Manuale utente

Watercool

Watercool HEATKILLER GPU-X3 GTX 670 Manuale utente

Watercool

Watercool HEATKILLER V eBC Manuale utente

Watercool

Watercool HEATKILLER IV VGA Series Manuale utente

Watercool

Watercool HEATKILLER GPU-X GTX570 V2 LT Manuale utente

Watercool

Watercool HEATKILLER MB-X ASUS RAMPAGE IVBlack Edition Manuale utente

Watercool

Watercool HEATKILLER GPU-X3 Core Series Manuale utente

Watercool

Watercool HEATKILLER GPU-X3 GTX 560 Manuale utente

Watercool

Watercool HEATKILLER GPU-X3 5970 Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente