watt box WB-800I-IPVM-6 Manuale utente
WB-800I-IPVM-6
Quick Start Guide
50 / 60 Hz 10A
220~240V~
WB-800I-IPVM-6
2
Important Safety Instructions
Read and observe the following safety points at all times.
Notice
For indoor user only. Internal components are not sealed form the environment. The device can only be used
in a fixed location such as a telecommunication centre, or a dedicated computer room. When you install
the device, ensure that the protective earthing connection of the socket-outlet is verified by a skilled person.
Suitable for installation in Information Technology Rooms in accordance with Article 645 of the National
Electrical Code and NFPA 75.
Only use brackets/attachments/accessories specified by the manufacturer.
Do not place the device in an unstable position where it might fail and cause injuries. This equipment is not
suitable for use in locations where children are likely to be present.
Do not cover this device with a cloth. Do not install it on a carpet or rug.
3
Package Contents
This package contains:
#10 × 12.5mm
clip screws (2)
Power strip
Mounting clips (2)
Rack ears (2 short, 2 long)
Nuts (2)
Removable, region-specific power cord
IEC sleeve (1) Rack ear screws (8)
50 / 60 Hz 10A
220~240V~
4
Front Panel
A. Power Inlet: For a 3-prong IEC power cord.
B. Circuit Breaker Reset Button: Press this button to restart the WattBox after an overload.
C. AC Power Switch: Press to manually toggle the outlets on or o. This glows with an amber light when the unit is
powered.
D. Safe Voltage Button: Toggles the Safe Voltage feature on and o, which protects your gear using normalized
power flow. The LED is illuminated when Safe Voltage is on.
E. Indicator LEDS: See the system status, Internet activity, auto reboot, safe voltage, surge protection, and grounding
(see page 11).
F. Network Connection: Connect to the Local Area Network (LAN) for IP control and monitoring.
G. Accessory Port: For connection to WattBox accessories.
H. UPS Link: For connection to a WattBox UPS unit (for future use).
I. Reset Button: Use a thin tool (paper clip, toothpick) to press this to restart the network card (no settings are
changed). Press and hold 5 seconds to set the power strip to DHCP. Press and hold for 10 seconds to reset the
power strip to factory default.
J. Controllable Outlets: All outlets are switchable (IP controlled).
K. Power Indicators: These illuminate when power to the matching outlet is on.
50 / 60 Hz 10A
220~240V~
A B F G H I K
J
EDC
5
Rack Ear Mounting Options
The long rack ears allow you to mount the unit at varying depths within the rack, as shown here.
Surface
mounting
Recessed
mounting
6
Rack Ear Mounting Options
The rack ears can be used to mount the power strip in several arrangements other than on the rack. You can
mount it under a counter or shelf (below left), on top of a table (below right), or against the wall (not shown).
With each of these options, you can choose to mount it flush to the surface (bottom) or displaced (top). In
addition, you can mount the unit at angled increments of 45°. See our website for examples.
7
Rack Mount with Clips
This can be mounted vertically on the outside of one
rail of a rack.
Using the nuts and screws provided, install the
mounting brackets (with the clips oriented as shown
at right) on the outside of one rack rail. Place the clips
76mm (3") – 102mm (4") from each end of the power
strip.
Mount the Strip
Align the power strip with the inside of one edge of
the mounting bracket. Apply pressure and rotate until
the units snaps into place.
50 / 60 Hz 10A
220~240V~
WB-800I-IPVM-6
8
Wall Mount with Clips
This unit can also be mounted on a wall, either vertically or horizontally.
Draw a level or plumb line. Using wall anchors or other appropriate hardware (not provided), attach the
mounting brackets (clips oriented as shown) centered on the level or plumb line, so that the clips are 76mm
(3") – 120mm (4") from each end of the power strip. For the greatest stability and safety, we recommend you
mount the brackets to studs wherever possible.
Next, insert the unit as described in Mount the Strip, on the previous page.
9
Connections and setup
If you desire OvrC connectivity, plug a network cable from your router or switch into the network port.
Plug in the IEC power cord. To prevent an accidental disconnect, insert the included IEC sleeve before
plugging in the power cord.
Mobile
Apps
Web Browser
Access
WANLAN
Router
WB-800I-IPVM-6
50 / 60 Hz 10A
220~240V~
10
Claiming the WattBox on OvrC
The WB-800I has many powerful features that are accessed through OvrC, our award-winning remote
management tool.
If you are not familiar with OvrC, visit snp1.co/ovrc to learn more.
Finishing Setup with OvrC
1. Ensure the WB-800I is connected to the internet via your router or network switch.
2. Log in to your OvrC account.
3. Add the WB-800I by entering its MAC address and service tag (ST) number.
You can now complete setup through OvrC. Ensure your firmware is up to date, schedule automatic reboots,
set up power-on delays, etc.
Indice
