Watts Premier FILTER-PURE Manuale utente

INSTALLATION, OPERATION AND MAINTENANCE MANUAL

MODEL

FILTER-PURE

Watts Premier, Inc. 8716 W Ludlow Drive Suite #1 Peoria, AZ 85381

Phone: 800-752-5582 www.wattspremier.com Fax: 623-866-5666

Part # 199408 Manual Date: 10/26/2011

Please read carefully before proceeding with installation. Your failure to follow any attached instructions or

operating parameters may lead to the product’s failure.

Refer to enclosed warranty for operating parameters to ensure proper use with your water supply.

Thank you for your purchase of a state of the art Watts Premier Water Treatment system.

This lter pure system is equipped with a unique swivel valve in head push button assembly. This

allows for a simple and sanitary push button lter change that does not require you to turn off the

water source to the ltration system.

This two stage system is equipped with a sediment prelter and a high quality carbon block lter.

The sediment lter reduces the sand, silt, sediment and rust particles that may be in your water.

The high end carbon block lter reduces the chlorine tastes and odors that may be in your water,

providing you crisp clean great tasting water at your tap.

Watts Premier also has a series of replacement lters that t into this unique swivel head system.

These include:

Granular Activated Carbon lter for chlorine, taste and odor reduction with higher ow.

Ultra Filtration Membrane for greater particle reduction including cysts like Cryptosporidium,

Toxoplasma, Giardia and Entamoeba.

Lead and VOC lter block for the reduction of lead and harmful chemicals. It is estimated that

VOC’s are present in one-fth of the nation’s water supplies. These water contaminants can

enter ground water from a variety of sources including localized use of herbicides and pesticides,

gasoline or oil spills, leaking underground fuel tanks, septic system cleaners, and chemicals used

in the dry-cleaning industry.

System Maintenance

Just because you can not taste it, does not mean that it is not there. Many contaminants in the

drinking water are undetectable to the taste. Additionally, over time if you do not replace the

lter elements, other bad tastes and odors will be apparent in your drinking water. This is why

it is important to change your lters at the recommended intervals as indicated in this system

manual.

When replacing any of the lter elements, pay special attention to any cleaning instructions. Should

you have any further questions please refer to our web site at www.wattspremier.com or call our

customer service department at 1-800-752-5582.

Table of Contents

Operational Parameters ................................................................................................

Contents of the Filter-Pure System ...............................................................................

Tools Recommended For Installation ............................................................................

FlowDiagram..................................................................................................................

Attach Tubing to System................................................................................................

Mount the System Under the Sink.................................................................................

Drill / Punch a Hole for the Faucet..................................................................................

Faucet Installation .........................................................................................................

Connecting Blue tube to faucet.......................................................................................

Adapt-a-Valve Installation...............................................................................................

System Start Up.............................................................................................................

Filter Change..................................................................................................................

Performance Data Sheet ...............................................................................................

Other Products by Watts.................................................................................................

Warranty Registration.....................................................................................................

Service Record...............................................................................................................

Warranty ........................................................................................................................

11-12

13-14

With proper installation and maintenance, this system will provide you with high quality water

for years to come. All of our water enhancement products are rigorously tested by

independent laboratories for safety and reliability.

√ 1 FILTER PURE Unit √ 1 Parts Bag √ 1 Green Tube

√ 2 Filters √ 1 Faucet Assembly √ 1 Blue Tube

If any of the items are missing, please contact Watts Premier prior to installing

Contents of the Filter-Pure System

Operational Parameters

Maximum Minimum

Operational Temperature 100°F (37.8°C) 40°F (4.4°C)

Operating Pressure 85 psi (5.98 kg/cm²) 20 psi (1.406 kg/cm²)

pH Parameters 10 5

Flow Rate 0.5 GPM @ 60 psig

Installation must comply with State and local plumbing regulations. Do not use with water that

is micro biologically unsafe or of unknown quality without adequate disinfection before or after

the system. System is intended to be installed using the cold water supply only.

Tools Recommended For Installation

√ 1/2" Diamond Tipped Hole Saw bit for faucet opening (Porcelain Sinks) or,

√ 1/2" Hole Saw Bit for faucet opening (Most Counter Tops - excluding marble) or,

√ 1/2” Round Knock out Punch for faucet opening (Stainless Sinks)

√ 1 1/4” Adjustable Wrench

√ 1/2" Open End Wrench

√ Adjustable Pliers

√ Sharp Knife

√ 1/8" diamond tip bit, pilot hole

√ Electric Drill

√ Phillips Screw Driver

√ Phillips bit for electric drill

Sink

Green

Tubing

Blue

Tubing

HOT COLD

Counter Top

Two Stage Under Counter (Filter Pure)

This system has been designed to t under most kitchen sinks.

Please read the entire manual carefully before proceeding with installation.

Mount the System Under the Sink

Step 4 Determine best location for the ltration system to be mounted near the cold water

supply angle stop valve to allow for future system maintenance.

Using the mounting holes on the system bracket, mark the location for the mounting

screwsonthecabinet wall.In theparts bag,locate the2 self tappingscrews. Using

an electric drill with a Phillips bit, screw them into the cabinet wall.

Mount the ltration system.

Step 5

Flow Diagram

Step 1 The two quick connect elbows are pre installed in to the back of the Filter-Pure

system. These elbows can be rotated in order to allow for the green and blue tube

Take the green tube and push in to the quick connect elbow that is by the red colored

sediment lter on the left of the system. Make sure the tube is fully pushed in all the

way to the tube stop.

Step 2

Take the blue tube and push in to the quick connect elbow that is by the yellow

colored carbon lter on the right of the system. Make sure the tube is fully pushed

in all the way to the tube stop.

Step 3

Attach Tubing to System

Step 8

Step 9

Determine desired location for the faucet on your sink and place a

piece of masking tape over where the hole is to be drilled. Mark the

center of the hole on the tape.

Step 6

Using a variable speed drill set on the slowest speed, drill a

“ pilot

hole through both porcelain and metal casing of sink at the marked

center of the desired location. Use lubricating oil or liquid soap to keep

the drill bit cool (If drill bit gets hot it may cause the porcelain to crack

or chip).

Using a 1/2” Drill Bit, proceed to drill the larger hole. Keep drill speed

on the slowest speed and use lubricating oil or liquid soap to keep the

hole saw cool during cutting.

Step 7

Drill a Hole for the Faucet in a Porcelain Sink

Punch a Hole for the Faucet in a Stainless Steel Sink

Drill a

“ pilot hole. Use a

” Hole Punch and an adjustable wrench

to punch the hole in the sink.

Step 10

The faucet can now be installed.

If mounting faucet to a Stainless Steel Sink you will need a 1/2”

Hole Punch. The faucet opening should be centered between the

back splash and the edge of the sink, ideally on the same side as

the vertical drain pipe.

Note:

Note: Most sinks are pre drilled with 1 ¼” diameter hole that you can use for your faucet.

(If you are already using it for a sprayer or soap dispenser, see step 1)

Porcelain sinks are extremely hard and can crack or chip easily.

Use extreme caution when drilling. Watts Premier accepts no responsibility for

damage resulting from the installation of faucet.

Diamond tip drill bit is recommended for drilling in porcelain.

After drilling, remove all sharp edges and make sure the surroundings

of the sink are cooled before mounting the faucet.

Connect Blue tube to Faucet

Faucet Installation

Step 11 In the faucet parts bag locate a brass compression nut, plastic

ferrulesleeve anda plastictube insert.Toassemble- placethe

compression nut on the open end of the blue tube attached

to the ltration system, then the plastic ferrule sleeve (small

tapered end of sleeve pointing to the end of tube), nally push

the white plastic insert all the way into the end of blue tube.

Insertthe assembled bluetubeinto thefaucetstem andtighten

the brass compression nut with a wrench.

DO NOT overtighten.

Choose the conguration that matches your faucet:

Adapt-a-Valve Installation

Conguration for 3/8”

(With Brass Fittings)

* Insert White Washer

Hot

Supply Cold

Supply Conguration for 1/2”

(Without Brass Fittings)

* Washer

Do not use Teon tape with the Adapt-a-Valve.WARNING:

Caution: Water supply line to the system must be from the cold water supply line only.

Hot water will severely damage your system.

Turnoffthecoldwatersupply to thefaucetbyturning the anglestopvalvecompletely

off. Open cold water on the sink faucet to relieve pressure.

Step 12

Step 13 Choosing the conguration that ts your plumbing, attach the adapt-a-valve as

illustrated in the three photos above.

*Do not forget to install the white compression washer for 3/8” conguration.

Locate the 1/4” green tube attached to the ltration system.

Insert the open end of the green 1/4” tube into the open 1/4”

quick connect tting on the plastic adapt-a-valve making

sure the tube is pushed in all the way passed the o-ring to

the tube stop.

Step 14 Green Tube

Adapt-a-Valve

Turn on the cold water supply at the angle stop valve, make

sure the adapt-a-valve is in the “ON” position and check for

leaks. Tighten/check any leaking ttings.

Step 15

System Start-up

Turn the faucet handle to the open position to start the ow

of water through the ltration system. Run approximately 7

gallons of water through the ltration system to ush out the

normal black carbon nes. The water may “sputter” until the

air is purged out from the system and the water may appear

cloudy due to air purging out from the system.

(Your faucet may vary).

Step 16

Once the ushing process is completed the water from the ltration system can be

used.

Step 17

Check for leaks over the next 24 hours.

Place a towel under the RO module to catch any excess water that

may drip out from the lters during the changeover.

Step 1

Your system is equipped with valved heads which will automatically turn off the

water supply to each lter when the lter is released, thus you do not need to turn

off the incoming water supply at the Adapt-a-Valve. The faucet must be off when

lters are replaced. To make the removal of the lter cartridges easier, the heads

& cartridges may be swiveled up to 90 degrees as shown in the pictures below.

Step 2

To install a lter cartridge: Remove the seal cap and insert

the cartridge into the valved head until you hear an audible “click”

(the button does not need to be pressed to install new lters).

Step 3

To remove a lter cartridge: Push & hold the button on the

valved head above the lter. Pull cartridge downward (from the

head) to remove. Release button and discard old lter.

Changing The Filter Cartridges

√ One sediment lter (Red Label P/N: 105311)

√ One carbon Block (Yellow Label P/N: 105351)

Replace:

6 Month System Maintenance

√ UF Membrane Filter (P/N: 105321)

√ Lead+Chemical Reducing CB (P/N: 105371)

Optional Filters:

Performance Data Sheet

Watts Premier Inc.

8716 W Ludlow Drive Suite #1

Peoria, AZ 85381

FILTER PURE

GENERAL USE CONDITIONS:

1: System has beenindependently tested for the removal of microbiologicallycontaminated water. The system is not intended

for the treatment of water that has an obvious contamination source, such as raw sewage. This system is not intended to

convert wastewater to microbiologically safe drinking water.

2: Operating Temperature: Maximum 100o F (37.8o C) Minimum 40o F (4.4o C)

3: Operating Water Pressure: Maximum 85-psi (5.98 kg/cm2) Minimum 20-psi

4: Maximum ow Rate: 0.50 gpm (1.89 lpm)

5: Rated Capacity: 2000 Gallons (7,500 liters)

RECOMMENDED REPLACEMENT PARTSAND CHANGE INTERVAL:

Note: Depending on incoming feed water conditions replacement time frame may vary.

Description Part Number Change Time Frame Cost

Stage 1: Sediment: 105311 6 Months $ 9.95*

Stage 2: Carbonblock 105351 6 Months $15.95*

*All prices subject to change without notice

This system has been tested according to NSF/ANSI Standard 42 for the reduction of the substances listed below. The concentration of the indicated

substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as

specied in NSF/ANSI 42. Testing performed under standard laboratory conditions, actual performance may vary.

California Proposition 65 Warning

WARNING: this product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. (Installer:

California law requires that this warning be given to the consumer). For more information: www.wattsind.com/prop65.

Contaminant   InuentChallengeConcentration  PercentReductionAchieved

ChlorineTaste&Odor   2.0mg/L+10%    97%

Particles     ClassIV     96%

Questions? Contact Watts Premier 800-752-5582 www.wattspremier.com

480-675-7995

Indice

Altri manuali Watts Premier Sistema di filtraggio dell'acqua

Watts Premier

Watts Premier RO-PURE 531401 Manuale utente

Watts Premier

Watts Premier RO-TFM-4SV Manuale utente

Watts Premier

Watts Premier WP-2 LCV Manuale utente

Watts Premier

Watts Premier HT-5-VOC-B Manuale utente

Watts Premier

Watts Premier Filter-Pure UF3 Istruzioni per l'installazione e il funzionamento

Watts Premier

Watts Premier WP-1 LCV Manuale utente

Watts Premier

Watts Premier ZRO-4 Manuale utente

Watts Premier

Watts Premier 500029 Manuale utente

Watts Premier

Watts Premier WP-2 LCV Manuale utente

Watts Premier

Watts Premier RO-PURE Manuale utente

Watts Premier

Watts Premier WP-4V Manuale utente

Watts Premier

Watts Premier WP-4V Manuale utente

Watts Premier

Watts Premier Filter Pure UF3 Manuale utente

Watts Premier

Watts Premier WP-2 LCV Manuale utente

Watts Premier

Watts Premier DELUXE PLUS Manuale utente

Watts Premier

Watts Premier CT-1 Manuale utente

Watts Premier

Watts Premier WP-5 Istruzioni generali

Watts Premier

Watts Premier WP-4 BVC Istruzioni generali

Watts Premier

Watts Premier Filter-Pure UF3 Manuale utente

Watts Premier

Watts Premier Zero Waste Retrofit Kit Manuale utente

Watts Premier

Watts Premier ZERO WASTE RETRO Manuale utente

Manuali Sistema di filtraggio dell'acqua popolari di altre marche

Wisy

Wisy LineAir 100 Manuale utente

Schaffner

Schaffner Ecosine FN3446 Series Manuale operativo

Pentair

Pentair FLECK 4600 SXT Guida utente

H2O International

H2O International H20-500 Manuale utente

Renkforce

Renkforce 2306241 Manuale utente

Neo-Pure

Neo-Pure TL3-A502 Manuale utente

FLTR

FLTR OBF Manuale utente

STA-RITE

STA-RITE VERTICAL GRID DE FILTERS S7D75 Manuale utente

Applied Membranes

Applied Membranes W-G844EM Manuale utente

BEGA

BEGA 116 Manuale utente

WATA

WATA Standard Manuale utente

Price

Price FFU series Manuale

Gaggenau

Gaggenau BRITA INTENZA 467873 Manuale utente

Brita

Brita SAFF-100 Manuale utente

HEISSNER

HEISSNER FPU24000-00 Manuale utente

BGS technic

BGS technic 1518 Manuale utente

Reverse Osmosis

Reverse Osmosis RF Series Manuale utente

ubbink

ubbink Filtramax Series Manuale utente