Wavetronix Click 210 Scheda tecnica
www.wavetronix.com
801.734.7200
Click Power Plant
INSTALLATION QUICK START GUIDE
1Identify the components
The following are included in the
Click power plant:
WARNING. Make sure power to AC mains is disconnected before wiring any of the
Click modules.
Mount each power plant device onto the DIN rail by hooking the lip over the edge
of the DIN rail and using a rocking motion to snap the module into place.
Follow the steps below to add a Click 210 circuit breaker and switch:
1 Mount the Click 210 onto the DIN rail.
2 Connect power in to the bottom of the module
3 Connect power out of the top of the module.
3Wire the Click 210 circuit breaker
2Mount the devices
Note. An authorized technician should perform installation and operation of these units. Persons other than authorized and
approved electrical technicians should NOT attempt to install the power plant, as there is a serious risk of electrical shock
through unsafe handling of the power source. Extreme caution should be used when connecting these units to an active
power supply.
One of the following power supplies will be included in the Click power plant:
Click 210
Circuit Breaker
Click 230
AC Surge
Click 201
AC to DC converter
Click 202
AC to DC converter
Click 204
AC to DC converter
Click 203
UPS/Battery (optional)
Wiring AC power in
Follow the steps below to properly wire an AC to DC power conversion module:
1 Mount the Click 201/202/204 onto the DIN rail.
2 Connect the line (hot) wire from the Click 230 into the L screw terminal on the top of the
Click 201/202/204. The line wire is usually black.
3 Connect the neutral wire from the Click 230 to the N screw terminal to the top of the Click
201/202/204. The neutral wire is usually white.
Wiring DC power out
To power the sensor, 10–30 VDC needs to be connected to the Click 200 in the pole-mount
cabinet. Additionally, if there is a main trac cabinet connected by a homerun cable, you will
need to connect DC power to the Click 200 in that cabinet.
1 Connect a +DC conductor (usually a red wire) to the + screw terminal on the bottom of the
Click 201/202/204.
2 Connect a -DC conductor (usually a black wire) to either of the - screw terminals on the
bottom of the Click 201/202/204.
Note. Do NOT connect to the DC OK screw terminal.
Some installations use a Click 203 instead of a Click 201/202/204. The Click 203 is covered in
Part 7 of this document.
5Wire the Click 201/202/204 AC to DC converter
4Wire the Click 230 AC surge
Follow the steps below to install the AC surge protection:
1 Mount the Click 230 onto the DIN rail.
2 Connect the line (hot) wire from the Click 210 terminal to terminal 5 on the IN side of
the Click 230.
3 Connect the neutral wire from the AC terminal block or cord to the terminal marked 1
on the Click 230.
4 Connect the ground wire from the AC terminal block or cord to the terminal marked 3
on the Click 230.
5 Connect the outgoing and protected neutral wire to the terminal marked 2 on the
Click 230.
6 Connect the outgoing and protected line wire to the terminal marked 6 on the Click 230.
7 Ground the system to the terminal marked 4 on the Click 230.
DC power (+) Ground (-)
Once the power plant is attached
to the DIN rail and wired correctly,
follow the steps below to verify your
connections:
1 Push the blue switch down on
the front of the Click 210 circuit
breaker.
2 Make sure that the Click
201/202/204 DC OK light is on.
7(Optional) Wire the Click 203
6Verify power is connected
If you are using the Click 203 UPS and battery module, follow
the steps below to correctly wire it:
1 Wire AC power into the UPS module by connecting the AC
line (black wire) to the L (+) terminal.
2 Connect the AC neutral (white wire) to the N (-) terminal.
3 Wire the supplied red wire from the + Battery terminal on
the UPS to the + OUT terminal on the battery.
4 Wire the supplied black wire from the - Battery terminal to
the -DC terminal on the battery.
5 DC power can be wired out of the UPS module by connect-
ing to the + and - OUT DC 24V 2A terminals.
6 Short R1 and R2. If you don’t, the UPS will not switch over to
the battery when the power goes out.
WX-500-0174
© 2021 Wavetronix LLC. All rights reserved. Protected in the US by patents viewable at www.wavetronix.com/en/legal. Protected by Canadian Patent Nos. 2461411; 2434756; 2512689; and European Patent Nos. 1435036;
1438702; 1611458. Other US and international patents pending. Wavetronix, SmartSensor, Click, Command and all associated logos are trademarks of Wavetronix LLC. All other product or brand names as they appear are
trademarks or registered trademarks of their respective holders. Product specifications are subject to change without notice. This material is provided for informational purposes only; Wavetronix assumes no liability
related to its use.
Black (live)
Green (ground)
White (neutral)
Black (ground)
Red (+24 VDC)
AC
power
source
Questo manuale è adatto per i seguenti modelli
5
Indice
Altri manuali Wavetronix Alimentazione elettrica
