Waycon MSB Series Manuale utente

FIRST STEPS

INSTALLATION GUIDE

Magnetostrictive Sensor Series MSB

For more information please see the data sheet at www.waycon.biz/products/magnetostrictive-transducers/

MOUNTING INSIDE A CYLINDER

Way on Positionsmesstechnik GmbH would like to thank you for the trust you have placed in us and our

products. This manual will make you familiar with the installation and operation of our magnetostrictive

sensors. Please read this manual carefully before initial operation!

Unpacking and checking:

arefully lift the device out of the box by grabbing the housing. After unpacking the device, check it for

any visible damage as a result of rough handling during the shipment. heck the delivery for

completeness. If necessary consult the transportation company, or contact Way on directly.

The cylinder head (in which the threaded hole will be drilled for inserting the transducer) must be made of

non-magnetic material. The residual magnetization caused by drilling the threaded hole must be less than

4 Gauss.

MSB...F1

MOUNTING INSIDE A CYLINDER

INSTALLATION GUIDE

Magnetostrictive Sensor Series MSB

For more information please see the data sheet at www.waycon.biz/products/magnetostrictive-transducers/

Thread M18x1,5

The sealing surface must be free from

scratches longitudinal or spiral.

Ro 1.6 μm for sealing with NON-pulsating pressure

Ro 0.8 μm for seals with pulsating pressure

Su ested o-rin :

PARKER 6-349 15,4x2,1

Material: Viton 90° Shore-A

Mixes: PARKER N552-90

MSB...F2:

measurement range

TECHNICAL DRAWING

MSB...F2

MSB...F1

Detail X

INSTALLATION GUIDE

Magnetostrictive Sensor Series MSB

For more information please see the data sheet at www.waycon.biz/products/magnetostrictive-transducers/

ELECTRICAL CONNECTION

ELECTRICAL CONNECTION MSB...N/K/E-F1

MSB...N-F1 MSB...K-F1 MSB...E-F1 Cable

0.1...10.1 V 0.1...5.1 V yellow

Output GND Output GND Output GND pink

Pow er Supply + Pow er Supply + Pow er Supply + brow n

Pow er Supply GND Pow er Supply GND Pow er Supply GND blue

4...20 mA

- The transducer must be installed in a grounded metallic cylinder.

- The braiding of the shielded transducer connection cable must be connected to the case of the female

connector so that the shielding is connected to the transducer case.

- The cable shielding on PL side must be isolated.

- If the transducer is installed in a cylinder isolated from the ground, the cable shielding on PL side must

be grounded.

- The transducer must be installed away from sources of magnetic fields, both static and 50 Hz (electric

motors, solenoids, etc.).

- The 24 VD feed must be dedicated to the transducers or must be drawn directly from the power

terminals and as near as possible.

- The sensors must be powered with non-distributed networks and always at lengths of less than 30 m.

- The magnetic cursor must be installed by placing a non-magnetic spacer (made of brass, aluminium,

stainless steel or plastic) between the piston surface and the cursor.

MSB

Standard Installation (recommended)

ELECTRICAL CONNECTION MSB...S-F1

DIGITAL OUTPUT MSB...S-F1

Series MSB... -S magnetostrictive transducers supply digital outputs in START/STOP format with RS422

differential serial transmission. The transducer requests an initialisation pulse that launches sampling.

The following pulses are transmitted on the outputs:

Start: the initialisation pulse retransmitted

Stop: the pulse corresponding to the position of each magnet.

The time between the Start pulse and the subsequent Stop pulses is proportional to the position of each

magnet according to the “magnetostrictive wave propagation speed” constant, equal to about 2900

m/sec.

P = Time * 2900 m/sec

The correct propagation speed for each product is shown on the product label.

Resolution in terms of metres is linked to the resolution used to measure time

1 μSec (1 MHz ) ==> 2.9 mm

10 nSec (100 MHz ) ==> 0.029 mm

1 nSec (1 GHz ) ==> 2.9 μm

The measurement reference is the leading edge of the pulse. Optimum width of the interrogation pulse

is 3 μsec, but the transducer works correctly for times from 1.5 to 5 μsec.

MSB...S-F1 Cable

Output + grey

Output - green

Input + yellow

Input - pink

Pow er Supply + brow n

Pow er Supply GND blue

In case of cable length shortening,

after cutting the cable take care of

soldering and insulating the green

and grey wires together

DIGITAL OUTPUT MSB...S-F1

INSTALLATION GUIDE

Magnetostrictive Sensor Series MSB

For more information please see the data sheet at www.waycon.biz/products/magnetostrictive-transducers/

ELEKTRISCHER ANSCHLUSS CANopenELECTRICAL CONNECTION MSB...F2

onnector output M12

MSB...F2

MSB...N-F2 MSB...K-F2 MSB...E-F2 PIN

0.1...10.1 V 0.1...5.1 V 1

Output GND Output GND Output GND 2

DO NOT ONNE T DO NOT ONNE T DO NOT ONNE T 3

Pow er Supply GND Pow er Supply GND Pow er Supply GND 4

Pow er Supply + Pow er Supply + Pow er Supply + 5

4...20 mA

MAGNETIC CURSOR

Order Code A B C D

P UR022 32.8 13.5 23.9 -

P UR023 32.8 13.5 23.9 11.0

P UR024 25.4 13.5 - -

P UR026 f or liquids 52.4 12.0 44.0 -

P UR027 f or liquids 52.4 15.0 44.0 -

Note:

P UR026 and P UR027 are supplied with kit PKIT036 for floating cursor for liquids.

Material P UR026, P UR027: stainless steel AISI 316

Please order magnetic cursor

separately (not included in the

delivery of the sensor).

P UR022 P UR023 P UR024 P UR026/027

TECHNICAL DATA

Electrical stroke ( .E.) [mm] Measurement range

Linearity < ±0.02 (min. ±0.06 mm)

MSB...F1 total length L [mm] Measurement range + 131.5 (excluding cable)

MSB...F2 total length L [mm] Measurement range + 140.3 (excluding connector)

Repeatability [mm] < 0.01

Hy steresis < ±0.005 %

Sampling time MR 50 to 1000: 1 / MR 1100 to 2000: 1.5 / MR > 2000: 2

MR: Measurement range

[msec]

DECLARATION OF EC-CONFORMITY

ACCESSORIES MSB...F2

K5P2M-S-M12

K5P5M-S-M12

K5P10M-S-M12

K5P2M-SW-M12

K5P5M-SW-M12

K5P10M-SW-M12

Connection cable analo output, 5-pole, s hielded

2 m, connector, straight

5 m, connector, straight

10 m, connector, straight

2 m, connector, angular

5 m, connector, angular

10 m, connector, angular

PIN Cable colour K5P..

1 brow n

2 w hite

3 blue

4 black

5 grey

Way on Positionsmesstechnik GmbH

Mehlbeerenstrasse 4

82024 Taufkirchen / Germany

This is to certify that the products

lassification Magnetostrictive Sensors

Series MSB

fulfill the current request of the following E -directives:

EMV-directive 2004/108/EU (until April 19th, 2016)

2014/30/EU (from April 20th, 2016)

applied harmonized standards:

EN 61000-6-2:2005, EN 61000-6-4:2007, EN 61326-1:2006

The declaration of conformity loses its validity if the product is misused or modified without proper

authorisation.

Taufkirchen, 24.02.2016 Andreas Täger, EO

Indice

Altri manuali Waycon Accessori

Waycon

Waycon LAM Series Manuale utente

Waycon

Waycon LLD-RS232 Manuale utente

Waycon

Waycon MH60 Series Manuale utente

Waycon

Waycon SX50 Series Manuale utente

Waycon

Waycon SX300 Series Manuale utente

Waycon

Waycon LVDT Series Manuale utente

Waycon

Waycon UFP Series Manuale utente

Waycon

Waycon LAS Series Manuale utente

Waycon

Waycon MAP Series Manuale utente

Waycon

Waycon EZ 105 Series Manuale utente

Waycon

Waycon SX Series Istruzioni operative e di manutenzione

Waycon

Waycon LX Series Manuale utente

Waycon

Waycon UFA-CP Series Manuale utente

Waycon

Waycon UFA2 Series Manuale utente

Waycon

Waycon MAB-A Manuale utente

Waycon

Waycon SX300 Series Manuale utente

Waycon

Waycon UFP Series Manuale utente

Waycon

Waycon LZW2 Series Manuale utente

Manuali Accessori popolari di altre marche

Hillco

Hillco 2810 Manuale utente

Siemens

Siemens QSA2700D Manuale dell'operatore

Contours

Contours ZY024 Manuale utente

Saivod

Saivod VS621 Manuale utente

Virtuox

Virtuox VirtuCLEAN 2.0 Manuale utente

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuale utente

Z-Wave

Z-Wave HSD-200Z Manuale utente

turck

turck FMX-IM-2UPLI63FX Manuale utente

Decagon Devices

Decagon Devices 10HS Manuale utente

UPPAbaby

UPPAbaby Cup Holder Manuale utente

Elko

Elko SmartSensor Leakage Wireless Manuale utente

Grizzly

Grizzly H8371 Manuale utente

Panasonic

Panasonic HG-T Series Manuale utente

IFM Electronic

IFM Electronic Efector 250 Series Guida di riferimento

DigiDesign

DigiDesign 888/24 I/O Manuale utente

PROZIS

PROZIS QUAY Manuale utente

patagonia

patagonia PSI Vest Manuale utente

SFC Energy

SFC Energy EFOY GO! Manuale utente