Wayel W2 Manuale utente

USER’S MANUAL

FIVE SRL

Via Cerodolo 4 | 40138 Bologna | Italy

T +39 051 0316272 | www.wayel.it | info@wayel.it

Welcome to the family of S3 owners! We will guide you to know each function for the right and safe use of Electric scooters. To ensure your

safety, please read this manual carefully before riding and make sure you are always following the requirements below:

Please contact the Local Customer Service Center if you have any questions about this bike. We are at our service at any time. Wish you safe and pleasant riding experience!

Fully understand the information in this manual, including but not limited to the relevant instructions, precautions and warnings.

Fully understand the operation and contingency measures of electric scooters.

Be fully aware of warning labels of S3 electric scooters.

We will not take any responsibility resulting from the unauthorized modiﬁcation, failure to use original spare parts, or installation of components

that affect the performance and safety of the scooter.

Safety Instructions

To ensure the safety of you and others, please make sure to observe the following matters:

Do not ride after you take medications which may affect your riding ability, drink alcohol, or when you are unwell.

Observe trafﬁc regulations and traffc signs and conﬁrm the surrounding road conditions and scooter conditions at any time, so as to actively avoid danger.

Wear safety equipment, such as helmet, and appropriate protective clothing if necessary, such as gloves and boots.

Perform a basic check each time before riding, so as to conﬁrm the light, brake, tread and tire pressure and check other parts for looseness or abnormal noise, and

regularly go to Local Service Center for maintenance.

In order to ensure the safety of you and others, please DO NOT use high beam in good lighting conditions. The continuous use of high beam will cause the visual

disturbance to vehicles and pedestrians on the opposite side, thus affecting normal driving.

Please do not make or answer any call during riding, which is likely to cause traffc accidents.

1 2

DESCRIPTION OF COMPONENTS AND PARTS

Installation of Mirrors

Take out the Left and Right mirrors,Insert the hole and rotate the

mirror clockwise to the correct position.

Use the spanner to fasten the nut,make sure the left and right mirror

is on the same line and suitable for the driver’s view.

USER INSTRUCTIONS

3 4

Headlamp

Front position lamp

Horn

Direction indicator lamp

Speedometer

Controller

Converter Rear position lamp、Stop lamp

Rear direction Indicator

License lamp

Electric engine

SCHEMATIC DIAGRAM OF COMPONENTS AND PARTSSCHEMATIC DIAGRAM OF COMPONENTS AND PARTS

Diagram of Instrument Panel

Speed display - Display current speed.

Ambient temperature - Display current temperture.

Driving time - Display Single driving time.

ODO/TRIP -Total ODO Distance/ TRIP distance.

Power display bar - Display current battery level.

Gear display - Display current gear.

Failure warning - Display current Failure (Motor,Controller,Brake, Accelerator)

Left Winker indicator - Flashing in synchronization.

READY light - Ready for driving.

The charge indicating lamp of Battery - Light up when battery’s low capacity.

Right Winker indicator - Flashing in synchronization.

Parking gear - Parking the scooter.

Recover display - When the scooter have failure warning on the Components.

(motor/controller/brake/accelerator),always press this button,driving the scooter

slowly to find the nearest service.

ODO

TRIP

mile

READY

100%

km/h

MODE

℃

5 6

OPERATION GUIDE

Details of Instrument Panel

OPERATION GUIDE

How To Operate The Smart Remote Contol

With the advanced Smart Remote Controller, you can easily lock or unlock your

electric scooter by simply pressing the button within 50 meters.

Unlock

Press the unlock button, and the start button stays on. The scooter enters

into the [Unlocked State].

Lock

When the scooter is in the [Static State], press the lock button, and the start

button ﬂashes. The scooter enters the [Locked State].

Remote keyless entry

After unlock the scooter,press this button twice within two(2) seconds, and

the scooter will be in the “Powered” state without key.

Search key

Press this witch within 50m, “Bi Bi” sounds searching the scooter.

7 8

Dial to the left side to turn on the Left winker.

Dial to the right side to turn on the Right winker.

Left Start Button Right Start Button

High/Low beam switch button

Winker button

OPERATION GUIDE

Press up to turn on the high beam.

Press down to turn on the low beam.

Press to make a sound and release to stop.

Horn button

Dial up to turn on the headlamp.Turn downward to AUTO to automatically

turn on the headlights. The headlights turn on automatically according to

the brightness of the environment.

Dail down to to turn off the headlamp.

Gear shift button

Headlamp button

The bike has three(3) Gear modes,1 "Eco", 2 "Cruise", and 3 "Sport". Dial

rightwards for "Eco", middle for "normal"and left for "sport".

Parking button has two modes: press to park the bike and parking indicator P

goes on; and press again to exit the parking status.

Parking button

When the scooter have failure warning on the motor/Controller/Brake/Accelerator,

always press this button, slow driving to nearby service center for repairs.

Recover button

After the scooter stops, turn the handlebar to the far left, insert the key into the physical

handlebar lock, push and rotate it leftwards to lock the scooter.

Insert the key into the physical handlebar lock, and rotate it rightwards to unlock the scooter.

Insert the key and rotate it leftwards, open the saddle and the storage box will be opened when

you hear a [Click] sound.

Insert the key and rotate it rightwards, to start the scooter for driving.

OPERATION GUIDE

IGNITION

OPEN

PUSH

910

Checks Before Riding

RIDING GUIDE

Whether the handlebar is stable and ﬂexible when turning.

Whether the switches on the right and left handlebars can work normally.

Whether the speed accelerator can work normally.

Make sure the tire pressure is normal. The suggested tire pressure is 26-29psi for front wheel and 29-32 psi for rear wheel.

Check tire surface for cracks, damage, wear, and foreign matter puncture or attachment

Whether the tread depth is suffcient (>0.8 mm).

Whether any fault warning light on the instrument panel goes on after being powered.

Whether the battery is fully charged.

Whether the head and tail lights, brake lights and winkers can work normally.

Whether the horn can work normally.

Whether the rear mirrors are clean. Adjust them to the appropriate angle.

Whether the brake oil is suffcient, and whether the handlebars and brake system can work normally.

For any abnormality or operational concern, please contact local Customer Service Center.

Make sure to check the following items before riding a Electric Scooter, which will guarantee your safety on the road.

OPERATION GUIDE

As the protection switch for the main power of electric scooter, the air switch will automatically disconnect to ensure safety when

the scooter circuit is abnormal or the current caused by short circuit exceeds the set safe value.

Unlock and Remove the battery case step by step

Open the Seat with the key, unplug the power cable, then pull up the battery case

with one hand.

Open the Seat with the key,plug the battery cable inside the socket,

connecting the battery with scooter.

Before open the key,please turn ON this Air switch in advance.

NOTES：In order to protect your safety, please turn off the air switch when

cleaning, storing the scooter for a long time, or re- moving the battery pack.

Air switch ON/OFF

Operation of Air switch

11 12

Insert the main charger plug into the charging port of the scooter.

Insert the chargers AC power plug into the home power socket, and the battery starts charging when the charger indicator turns red.

The battery is fully charged if the charger indicator turns from red to green.

How to Charge the Battery

BATTERY USE INSTRUCTIONS

Charging Interface

TIPS:

CHECKS BEFORE RIDING

Insert the key and turn leftwards, “Powered” state is started, the Instrument

is opened, and the “READY” light is ON,scooter is ready for driving now.

Press the "P" button with three(3) seconds, to exit the Parking

state,and the “P” indicator goes off,then you can start driving.Gently

turn the handlebar to ride on the road.

Before riding,make sure the electronic side stand retracted and

rotate the handlebar to ensure that the handlebar lock is closed.If

the Parking button is pressed when riding, the bike will be dis-

energized. So DO NOT press it when riding for avoiding danger

caused by the sudden loss of power.

If the electronic side stand is extended when riding, the bike will be

dis- energized. So DO NOT extend the electronic side stand when

riding for avoiding danger caused by the sudden loss of power.

The scooter must be fully stopped before starting. In case of

abnormality during riding, please ride carefully or push it to a safe

place. DO NOT try restarting the bike during riding or on the lane so

as to avoid danger.

Put on the helmet, and retract the electronic side stand.

ODO

TRIP

mile

READY

100%

km/h

MODE

℃

Make sure to check the following items before riding, which will guarantee your safety on the road.

Insert the key and turn leftwards, Open the saddle,

open the cap to conect the battery cable, Turn On the Air switch.

13 14

BATTERY USE INSTRUCTIONS

How to Charge the Battery

TIPS:

Short circuit of the cathode and the anode at the battery's input.

Keep it away from children, ﬁre and heat source. It is strictly forbidden

to throw it into the ﬁre;Violent movements, shock and extrusion are

prohibited;

Only the speciﬁed charger can be used, and other chargers are

prohibited to charge the battery;

This product has been subject to strict inspection before leaving

factory, and it is strictly prohibited to dismantle it. Please contact our

company's after-sales department for any question.

TIPS:

Do not expose the battery to water, and prevent it from being

damped by water or rained.

Charge temperature: 0-45 °C, discharge temperature: -20-45 °C;

Battery capacity will be reduced when placed in a low-temperature

environment;

Charge the battery when you use it, but make sure to charge it before

the capacity is lower than 20%. When it is not used

for a long time, please remove it from the scooter.

Pull up the battery from scooter,Insert the main charger plug into the charging socket of the battery. Insert the chargers AC power plug into the home power

socket, and the battery starts charging when the charger indicator turns red.The battery is fully charged if the charger indicator turns from red to green.

Storage, Maintenance and Transportation

BATTERY USE INSTRUCTIONS

Please charge the battery to half-saturation state when storing or transporting it (after the battery is discharged, charge it for 3 hours).

Place it in a dry and ventilated place;

Battery and charger should be kept in a clean,dry,and ventilated place. Keep them away from corrosive materials,power source and heat source;

Storage conditions: ambient temperature -20-35 °C, humidity <65% RH;

When storing the charger, please disconnect it from the battery.

Regular maintenance can enhance the service life and driving safety of the electric scooter. Please refer to the following suggestions and take care of your

scooter.

The scooter has no electricity,

and the READY lamp does not

shine.

When turning the speed

regulating steering handle-bar,

the motor does not turn after

being powered.

Speed is slow or mileage is

short.

Battery can not be charged.

Battery is poorly connected.

Air switch is not turned on.

Low battery volume.

Side stand is not retracted.

Brake handle does not reach the right position.

Steering handlebar failure.

The controller plug is loose.

Controller failure.

Low battery.

Under-inﬂated tire.

Heavily overloaded.

Brake pads interference.

Battery aging or normal scrap.

Poor contact of the main plug of the charger.

Do not use the wrong charger.

Battery aging or normal scrap.

Battery low-voltage protection.

Charge the battery.

Inﬂate the tire, and check the tire pressure before riding.

Foster a good habit, and keep the appropriate load Change

the brake pads and check the brake system before riding.

Change battery.

Check whether the main plug is in a right place Use the

special charger.

Contact of the main plug again.

Contact with local service ofﬁce of battery.

Charge the battery.

Put away the side stand.

Close the parking key.

Place the brake handle at the right position.

Change handlebar.

Re-plug controller.

Change controller.

Connect the battery properly at its main plug.

Turn on the air switch.

Regular maintenance can improve the service life and driving safety of the electric scooters.

Please refer to the fol-lowing suggestions and take care of your scooter.

ROUTINE CLEANING AND MAINTENANCE

Failure Causes Solutions

15 16

ROUTINE CLEANING AND MAINTENANCE

Routine Cleaning and Maintenance

Regular Inspection and Maintenance

Cleaning：Please use clean water and neutral detergent to clean it, and use soft cloths and sponges to clean the surface;

It is prohibited to use metal brushes, sandpaper or the like to clean it, in order not to scratch the parts surface. After cleaning, dry it with soft cloths.

TIPS:

Please disconnect the air switch before cleaning.

Do not use strong water jet to directly wash it, so as to avoid the default of mechanical parts caused by water invasion.

Storage: try to park it in a dry and cool room to reduce the exposure to sun and rain and avoid the reduction of service life due to corrosion of parts.

When left unused for a long time, please turn off the air switch and disconnect the power supply circuitto prevent over discharging.

After long-term storage, please fully charge it before use.

The new scooter must be subject to the ﬁrst inspection and maintenance in the Service Center when it reaches 1,000 km or two months (whichever comes ﬁrst).

The scooter is recommended to be subject to regular inspection and maintenance in the Service Center at every 3,000 km or six months (whichever comes ﬁrst).

Please disconnect the air switch before cleaning.