WeatherTech WindshieldFone Manuale utente

WindshieldFone

Installation Video

Step 1: Choosing the Length

Rubber Bumper

Knob A

Knob B

Knob C

Knob D

Knob E

Base

Base Lever

Holder

3” Short Arm

5” Medium Arm

Telescopic Arm

Determine a safe, convenient location to mount on

your windshield. We recommend keeping it as low

on the windshield as possible.

Contents: WindshieldFone, 3” Short Arm, 5” Medium Arm, Rubber Bumper

Note: We recommend reading all instructions prior to beginning.

Note the length between your windshield and the

front of your dashboard.

Start with the installed telescopic arm, and extend

or retract as necessary to see if it ﬁts your dash. If

so, you’re ready to mount. If the telescopic arm is

too long, you can easily swap it out with either the

included 3” Short or 5” Medium Arm.

The suction cup Base can be ﬂipped to allow for

easier mounting.

A B

67WF1

Step 3: Swapping out for Shorter Arms

Step 2: Adjusting the Attached Telescopic Arm

Loosen Knobs C and D until you can adjust the

telescopic arm to perfectly ﬁt your dashboard.

When the dash allows, the Holder can sit over the

edge of it. Tighten Knobs C and D.

First, loosen and remove Knob B, and remove

the WindshieldFone Holder. Then on the Base,

loosen and remove Knob E while securing the

bolt head on the opposite side. Remove bolt, then

spread the base to remove the arm. Depending on

placement, the base can also be ﬂipped to ease

mounting.

Add the Base to the opposite end of the Arm at its

hinge.

Choose your preferred 3” Short Arm or the 5”

Medium Arm. Installation of both is easy:

Slide the bolt into the hinge, and while holding the

bolt head, add and tighten Knob E until secure.

To increase stability, add the Rubber Bumper to

the section of the telescopic arm that’s closest to

the edge of the dashboard.

3” Short Arm

5” Medium Arm

Position the swivel section of the Arm against the

screw on the rear of the WindshieldFone Holder,

then add and tighten Knob B until secure.

67WF1

Step 5: Adjusting to Your Phone Width

Loosen Knob A and fully open the phone holder.

Place your phone into the Holder and adjust it to

ﬁt the width of your phone.

Step 4: Mounting WindshieldFone

Clean the windshield surface where you intend to

adhere the suction cup, then let dry completely.

We recommend using rubbing alcohol to clean

both the windshield and the suction cup.

Firmly press the Suction Cup against the

windshield.

While maintaining pressure on the base of the

mount, press the lever toward the windshield until

it snaps securely into place.

Ensure the Lever on the Base is in the release

position and that Knobs C and D are facing up.

Tighten Knob A.

K L

67WF1

Step 6: Adjusting Your Viewing Angle

Loosen Knob B to rotate, swivel or tilt the Holder

until you ﬁnd the ideal viewing angle, and then

tighten Knob B to secure. Ensure all knobs are

secured ﬁrmly prior to use.

Step 7: Removing Your Phone

Place your thumb and foreﬁnger on either side of

the patent-pending Quick Lock & Release tabs and

press with your thumb until your phone pops out.

Note: Please check state and local laws prior to use.

LET’S TALK

800-441-6287 or 630-769-1500

For warranty information, please visit www.WeatherTech.com/warranty

67WF1

Made in USA

Altri manuali WeatherTech Accessori per automobili

WeatherTech

WeatherTech BMW E71 X6 SAC Manuale utente