Webee Micro Motion Sensor Manuale utente
Webee-Centralite-3328
GETTING STARTED WITH MICRO MOTION SENSOR
1
2
GETTING STARTED WITH
MICRO MOTION SENSOR
This document is the property of Webee L.L.C.. The data contained here, in whole or in part, may not be duplicated, used or
disclosed outside the recipient for any purpose. This restriction does not limit the recipient's right to use information contained
in the data if it is obtained from another source without restriction.
Webee-Centralite-3328
GETTING STARTED WITH MICRO MOTION SENSOR
2
2
Getting started Page 0
INDEX
Section 1: Mounting your Micro Motion Sensor
Instructions / Dimensions.....................................................03
Section 2: Connecting to Smartee
Adding Micro Motion Sensor to Zigbee Network..........................04
Section 3: Specs
Removing Micro Motion Sensor from Zigbee Network.................04
Section 4: Security Instructions
Security Guidelines.............................................................06
Electrical Specifications......................................................05
RF characteristics...............................................................05
© 2016 Webee LLC, All rights reserved. Webee and the Webee logo are trademarks or registered trademarks of Webee LLC.
Webee-Centralite-3328
GETTING STARTED WITH MICRO MOTION SENSOR
3
2MOUNTING YOUR MICRO MOTION SENSOR
The Micro Motion Sensor can be installed using either adhesive strips or mounting screws.
The easy-to-install mounting plate attaches with a single screw and the sensor
simply slides into place on the mount. The Motion Sensor ships with the battery
pre-installed.
Getting started
1
1
Page 0
Instructions
Dimensions
© 2016 Webee LLC, All rights reserved. Webee and the Webee logo are trademarks or registered trademarks of Webee LLC.
1.12”
(28mm)
1.75”
(44mm)
FRONT VIEW SIDE VIEW
1.75”
(44mm)
Webee-Centralite-3328
GETTING STARTED WITH MICRO MOTION SENSOR
4
2CONNECTING TO SMARTEE
Getting started
1
2
Page 0
To join the Micro Motion Sensor to the Smartee, make sure you pull the small plastic tab
located at the bottom of the sensor and immediately click on "Add Device" on your
Webee App. The sensor will automatically join the network.
If the Micro Motion Sensor does not automatically join the network, remove cover from
sensor and remove battery. While holding down the config button, reinsert battery to
factory reset the device.
If after following these steps the sensor does not join the Smartee network, do as
follows:
•Make sure the Micro Motion Sensor batteries are charged.
•Ensure it is within RF range of a Smartee (30-90 ft indoor).
Once the Micro Motion Sensor is added, you will be able to start controlling it trough
your Webee App.
If it becomes necessary to remove the Micro Motion Sensor from a Zigbee network a
factory reset to default on the device will be requiered.
A. Remove cover from sensor and remove the battery.
B. Press and hold the reset button while reinserting the battery.
Adding to Zigbee Network
Removing from Zigbee Network
© 2016 Webee LLC, All rights reserved. Webee and the Webee logo are trademarks or registered trademarks of Webee LLC.
Config button Status
Led
Webee-Centralite-3328
GETTING STARTED WITH MICRO MOTION SENSOR
5
2MICRO MOTION SENSOR SPECS
1
3
2
3
Description
Min
Typ
Max
Unit
Rated
-
-
3
V
Battery
-
CR-2450 (1x)
2
Years
Operating temperature
0º
-
40º
ºC
Storage temperature
-20º
-
50º
ºC
Operating Humidity
0
-
90%
RH (non-condensing)
Electrical specifications
Description
Min
Typ
Max
Unit
RF Channels
-
-
16
-
TX Strength
-
-
+8
dBm
Range
-
-
130+ ft. (40+ m)
L.O.S.
ft.
Temp Accuracy:
±0.4 °C (max),
–10 to 85 °C
°C
Protocol
Zigbee HA 1.2
Wireless RF Characteristics
Getting started 5
Page 0
© 2016 Webee LLC, All rights reserved. Webee and the Webee logo are trademarks or registered trademarks of Webee LLC.
Webee-Centralite-3328
GETTING STARTED WITH MICRO MOTION SENSOR
6
2SAFETY INSTRUCTIONS
Getting started
1
3
Page 0
Safety Guidelines
-Clean only with a dry cloth.
-Do not install near any heat source such as radiators, stoves or
other appliances (including amplifiers that produce heat).
-Only use attachments and accessories specified by the manufacturer.
-Follow all guidelines carefully, if you have any questions contact us at
Warning: No user-serviceable parts inside. Refer all servicing
to qualified service personnel.
Warning: Lift the top of your Micro Motion Sensor to
change it’s battery. The sensor use CR-2450 (1x)
batery.
Risk of explosion if another type of battery is used.
© 2016 Webee LLC, All rights reserved. Webee and the Webee logo are trademarks or registered trademarks of Webee LLC.
Webee-Centralite-3328
GETTING STARTED WITH MICRO MOTION SENSOR
7
2
V1.0 REV. June, 2016
© 2014 Webee LLC, All rights reserved. The Webee logo, Boss and Bees are trademarks or registered trademarks of Webee LLC
Indice
Altri manuali Webee Accessori
