WEG DeviceNet CFW500 Istruzioni operative

Ethernet Communication

Plug-in Module

Módulo Plug-in de

Comunicación Ethernet

Módulo Plug-in de

Comunicação Ethernet

CFW500

Installation, Conﬁguration and Operation Guide

Guía de Instalación, Conﬁguración y Operación

Guia de Instalação, Conﬁguração e Operação

Motors | Automation | Energy | Transmission & Distribution | Coatings

Summary / Índice

English

EspañolPortuguês

SUMMARY

1 SAFETY INFORMATION...............................5

1.1 SAFETY WARNINGS ...................................5

1.2 PRELIMINARY RECOMMENDATIONS.......5

2 GENERAL INFORMATION...........................5

3 CONTENTS OF THE PACKAGE...................5

4 ACCESSORY INSTALLATION .....................6

5 SETTINGS......................................................6

APPENDIX A – FIGURES...............................18

ÍNDICE

1 INFORMACIONES DE SEGURIDAD ...........9

1.1 AVISOS DE SEGURIDAD .............................9

1.2 RECOMENDACIONES PRELIMINARES.....9

2 INFORMACIONES GENERALES.................9

3 CONTENIDO DEL EMBALAJE....................9

4 INSTALACIÓN DEL ACCESORIO..............10

5 CONFIGURACIONES..................................10

ANEXO A – FIGURAS.....................................18

ÍNDICE

1 INFORMAÇÕES DE SEGURANÇA............14

1.1 AVISOS DE SEGURANÇA .........................14

1.2 RECOMENDAÇÕES PRELIMINARES.......14

2 INFORMAÇÕES GERAIS ...........................14

3 CONTEÚDO DA EMBALAGEM..................14

4 INSTALAÇÃO DO ACESSÓRIO.................15

5 CONFIGURAÇÕES......................................15

ANEXO A – FIGURAS.....................................18

Ethernet Communication Plug-in Module

English

CFW500 | 5

1 SAFETY INFORMATION

1.1 SAFETY WARNINGS

NOTE!

Only use the Ethernet communication

plug-in module (CFW500-CETH-IP,

CFW500-CEMB-TCP, CFW500-CEPN-IO)

on WEG inverters of the CFW500 line.

Read the user’s manual of the CFW500

and the user’s manual of the Ethernet

before installing or operating this

accessory.

This guide contains important information

for the correct understanding and proper

operation of this module.

1.2 PRELIMINARY RECOMMENDATIONS

ATTENTION!

Always disconnect the general power

supply before connecting or disconnecting

the accessories of the frequency inverter

CFW500.

Wait for at least 10 minutes to guarantee

complete de-energization of the inverter.

2 GENERAL INFORMATION

This guide contains instructions for the installation,

configuration and operat ion of the Ethernet communication

plug-in module. There are three different modules

according to the specified communication protocol.

CFW500-CETH-IP: EtherNet/IP protocol.

CFW500-CEMB-TCP: Modbus TCP protocol.

CFW500-CEPN-IO: PROFINET IO protocol.

3 CONTENTS OF THE PACKAGE

When receiving the product, check if this package

contains:

Accessory in anti-static packaging.

Installation, configuration and operation guide.

Ethernet Communication Plug-in Module

English

6 | CFW500

4 ACCESSORY INSTALLATION

The accessory is easily installed or replaced. For correct

installation of the accessory execute the following steps:

Step 1: With the inverter de-energized, remove the front

cover of the inverter (Figure A1 on page 18).

Step 2: Remove, if present, the accessory (connected

plug-in module) according to Figure A1 on page 18.

Step 3: Fit and press the accessory to be installed as

indicated in Figure A1 on page 18 and then assemble

the front cover of the inverter.

Step 4: Power up the inverter and check if parameter

P0027 shows value 11 (P0027 = 11). If this information

is not true, check if the module has an Ethernet interface

and repeat steps 1-4.

5 SETTINGS

The control connections (analogical input / output, digital

inputs / outputs and RS485 interface) must be performed

as shown in Table 1 on page 6.

Table 1: Signals of control connector

Connector Description

Superior Terminal

1DI1 Digital input 1

3DI2 Digital input 2

5+24 V +24 Vdc power supply

7DO1-RL-NO Digital output 1

(NO contact of relay 1)

9DO1-RL-C Digital output 1

(common point of relay 1)

11 GND Reference 0 V

Inferior Terminal

2AO1 Analogical output 1

4AI1 Analogical input 1

6DO2-TR Digital output 2 (Transistor)

8 RS485 – A (-) RS485 (Terminal A- )

10 RS485 – B (+) RS485 (Terminal B+ )

12 Earth Protective earth input (used by

Ethernet connector frame)

Ethernet Communication Plug-in Module

English

CFW500 | 7

DI1

DI2

GND

DO1-RL-NO

RS485 - A

+24 V

DO1-RL-C

RS485 - B

GND

Earth

AO1

AI1

DO2-TR R

rpm

+24 V

Figure 1: Signals of the control connector

Besides the control connections, the module has a

connector for Ethernet interface, which follows the 100

Base-TX Fast Ethernet standard.

The location of the DIP-switches to select the kind of the

analog input and output signal and the termination of the

RS485 and network can be better viewed in Figure A2

on page 19. To use the analog inputs and/ or outputs

with signal in current, switch S1 and related parameters

must be set as indicated in Table 3 on page 8.

For further details about the control connections see

Ethernet Communication Plug-in Module

English

8 | CFW500

chapter 3 Installation and Connection of the CFW500

user's manual.

Table 2: Conﬁgurations of the switches to select the kind

of signal at the analog input and output on the CFW500

Ethernet module

Input /

Output Signal Setting of

Switch S1

Range of

Signal

Parameter

Setting

AI1

Voltage S1.1 = OFF 0...10 V P0233 = 0 or 2

Current S1.1 = ON 0...20 mA P0233 = 0 or 2

4...20 mA P0233 = 1 or 3

AO1

Voltage S1.2 = ON 0...10 V P0253 = 0 or 3

Current S1.2 = OFF 0...20 mA P0253 = 1 or 4

4...20 mA P0253 = 2 or 5

Table 3: Conﬁgurations of the switches for RS485 and

communication

Communication Switch Switch

Setting Option

RS485 S1(*)

S1.3 = OFF

and

S1.4 = OFF

RS485

termination

OFF

S1.3 = ON

and

S1.4 = ON

RS485

termination

(*) No other combinations of the switches are allowed.

This module has a connector (Figure A2 on page 19)

used by the CFW500-MMF Flash Memory Module, which

allows data transfer between inverters. For further details

on this accessory, refer to the installation and operation

guide of the CFW500-MMF.

Módulo Plug-in de Comunicación Ethernet

CFW500 | 9

Español

1 INFORMACIONES DE SEGURIDAD

1.1 AVISOS DE SEGURIDAD

¡NOTA!

Solamente utilizar el módulo plug-in de

comunicación Ethernet (CFW500-CETH-IP,

CFW500-CEMB-TCP, CFW500-CEPN-IO)

en los convertidores WEG línea CFW500.

Se recomienda la lectura del manual del

usuario del CFW500 y del manual del

usuario del Ethernet antes de instalar u

operar este accesorio.

El contenido de esta guía fornece

informaciones importantes para el correcto

entendimiento y buen funcionamento de

este módulo.

1.2 RECOMENDACIONES PRELIMINARES

¡ATENCIÓN!

Siempre desconecte la alimentación

general antes de conectar o desconectar

los accesorios al convertidor de frecuencia

CFW500.

Aguarde por lo menos 10 minutos para

garantizar la desenergización completa

del convertidor.

2 INFORMACIONES GENERALES

Esta guía orienta en la instalación, configuración y

operación del módulo plug-in de comunicación Ethernet.

Existen 3 módulos diferentes, conforme el protocolo de

comunicación especificado:

CFW500-CETH-IP: protocolo EtherNet/IP.

CFW500-CEMB-TCP: protocolo Modbus TCP.

CFW500-CEPN-IO: protocolo PROFINET IO.

3 CONTENIDO DEL EMBALAJE

Al recibir el producto, verifique si el embalaje contiene:

Módulo Plug-in de Comunicación Ethernet

10 | CFW500

Español

Accesorio en embalaje antiestático.

Guía de instalación, configuración y operación.

4 INSTALACIÓN DEL ACCESORIO

El accesorio es fácilmente instalado o sustituido. Para

la correcta instalación del accesorio, ejecute los pasos

a seguir:

Paso 1: Con el convertidor desenergizado, retire la tapa

frontal del mismo (Figura A1 en la página 18).

Paso 2: Retire, si existe, el accesorio (módulo plug-in

conectado) conforme la Figura A1 en la página 18.

Paso 3: Encaje y presione el accesorio a ser instalado

conforme indicado en la Figura A1 en la página 18 y

después conecte la tapa frontal del convertidor.

Paso 4: Energice el convertidor y verifique si el

parámetro P0027 indica el valor 11 (P0027 = 11). En caso

de que esa información no sea verdadera, verifique si el

módulo utilizado realmente posse una interfaz Ehernet

y repita los pasos 1-4.

5 CONFIGURACIONES

Las conexiones de control (entrada/salida analógica,

entradas/salidas digitales y interfaz RS485) deben

ser hechas en el conector conforme Tabla 1 en la

página 11.

Altri manuali per DeviceNet CFW500

Indice

Lingue:

Manuali Invertitore popolari di altre marche

Fourgroup

Fourgroup Easy Manuale utente

Velleman

Velleman PI300M Manuale utente

Sungrow

Sungrow SG350HX-US Manuale utente

WilTec

WilTec 61897 Manuale utente

SMA

SMA SUNNY BOY STORAGE 2.5 Manuale utente

Simplicity

Simplicity LANDLORD 316 Manuale utente

Santak

Santak SMAX 3000 Manuale utente

ATON

ATON RA.Store-3 Manuale utente

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Manuale utente

Tektronix

Tektronix CFG250 Manuale utente

Champion

Champion 200989 Manuale utente

Vanner

Vanner 20-500 Series Manuale utente

GE GEP Manuale utente

Astrel Group

Astrel Group Power Reducer Guida rapida

MULTIQUIP

MULTIQUIP GDP-5H Guida

GoWISE

GoWISE PS1007 Manuale utente

Promate

Promate PM13500D ES Manuale utente

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Manuale utente