Welbilt Kolpak HAR-C2-N1 Manuale di programmazione
Protecting Your Future
Air-Shield
Original Instructions
Installation, Operation and Maintenance Manual
This manual is updated as new information and models are released. Visit our website for the latest manual.
Part Number: 17280-4 08/19
2
Indicates a situation that, if not avoided, could damage the
refrigeration system or result in minor injury.
Safety Notices
NOTE: Indicates useful, extra information about the
procedure you are performing.
DANGER
Indicates a hazardous situation that, if not avoided, will
result in death or serious injury. This applies to the most
extreme situations.
Use appropriate eye protection during installation and
servicing.
Read this manual thoroughly before operating, installing or
performing maintenance on the equipment. Failure to follow
instructions in this manual can cause property damage, injury
or death.
Notice
Indicates information considered important, but not hazard-
related (e.g. messages relating to property damage).
Disconnect all power sources before servicing the refrigeration
equipment.
Sheet metal and coil surfaces have sharp edges. Use
appropriate protective gloves to prevent injury.
Ensure that all field wiring conforms to the equipment
requirements and all applicable local and national codes.
Installation and maintenance/servicing are to be performed
only by trained and qualified personnel familiar with
commercial refrigeration systems.
Indicates a hazardous situation that, if not avoided, could result
in death or serious injury.
3
Table of Contents
Section 1
General Information
Receiving Inspection............................................................................................................ 4
Warranty Information ......................................................................................................... 4
Section 2 Installation
Air Shield Installation ........................................................................................................... 5
Section 3
Cleaning Instructions
Air Shield Installation ........................................................................................................... 5
Cleaning Instructions ........................................................................................................... 6
Section 4
Electrical Wiring
Electrical Wiring 7
Diagram 1 – 115/1/60 W/ Magnetic Switch & Optional Motion Sensor..................... 8
Diagram 2 – 115/1/60 W/ Push Button Switch & Optional Motion Sensor................ 9
Diagram 3 – Component Locations ··········································································· 10
Diagram 4 – Installation Location Standard ······························································ 11
Diagram 5 – Installation Location Sliding Door W/ Motion Sensor··························· 12
Diagram 6 – Magnet Installation Location Standardt ··············································· 13
Diagram 7 – Magnet Installation Location W/ Recessed Door·································· 14
Section 5
Specifications
Specifications .................................................................................................................... 15
4
Section 1
General Information
Receiving Inspection
•Check the shipment carefully and compare to the bill of lading.
•Account for all items listed and inspect each container for damage.
•Carefully inspect for any concealed damage.
•Report any shortages or damages to the carrier, noteon the bill of lading, and file a freight claim.
•Damaged material cannot be returned to the manufacturer without prior approval.
•A Return Material Authorization (RMA) must be obtained. Contact a sales representative at 800-826- 7036.
Warranty Information
For information regarding warranty guidelines, claim form, product registration, warranty verification, or locating a service
provider please visit our website at www.kolpak.com or call 800-225-9916.
5
Section 2
Installation
Air Shield Installation
•Check the selected installation location to ensure that racks, braces, conduit, etc. are not in the way to properly mount
the Air-Sheild.
•To attach Kolpak Air Shield to wall on inside of Walk-in cooler, use the 8 screws provided in packet under shield cover.
•Remove screws along both outside edges of cover to remove cover assembly. Stand base assembly vertically adjacent
to edge of inside doorjamb and remove the tape backing; align with edge of door jamb and secure using the 8 screws
provided to attach the base to the jamb using the holes provided in the base.
•Base should be raised off the floor approximately ½” to allow room for the cover to be removed for cleaning.
•Attach door switch magnet to door in orientation shown in instruction sheet.
•Use 2 screws to attach magnet to door.
Note: Holes for attaching the base to the wall located on the door edge side are accessible thru slots punched in the
base.
•Units are designed for installation on the hinge side of doorjamb inside the walk-in compartment.
Place mounting base so that the edge is flush with the inside doorjamb. When mounted with the cover the edge of the
door opening should be flush with the edge of the Kolpak Air Shield cover.
Note: Mount in a manner to prevent any sharp edges from being exposed beyond the door opening.
6
Section 3
Cleaning Instructions
Cleaning Instructions
•To clean Kolpak Air Shield remove the cover assembly by removing the screws along each side of the cover assembly
and around the plate at the top of the assembly.
•Lift the cover assembly off the unit and clean using a mild detergent.
•Dry and replace cover assembly.
Note: If cleaning of any permanently attached component is required, take caution not to introduce water into the
motor assembly. Recommended cleaning method is to use air pressure to blow any debris from motor assembly area.
7
Section 4
Electrical Wiring
Electrical Wiring
•All electrical wiring and connections must conform to the National Electrical Code, local codes and regulations.
Note: Liquid tight flexible conduit is provided for connection to any acceptable circuit either inside or outside the walk-in
compartment.
8
Diagram 1. 115/1/60 W/ Magnetic Switch & Optional Motion Sensor
9
Diagram 2. 115/1/60 W/ Push Button Switch & Optional Motion Sensor
10
Diagram 3. Component Locations
Questo manuale è adatto per i seguenti modelli
1
Indice
Manuali Stufa popolari di altre marche
Empire Heating Systems
Empire Heating Systems WCC65 Manuale utente
Wetekom
Wetekom 92 86 43 Manuale utente
Desa
Desa SPC170-F Manuale utente
Watlow
Watlow Watrod Electric Tubular Heaters Manuale utente
Haverland
Haverland ECO-DRY GPS Series Manuale elenco delle parti
Stelpro
Stelpro ASILVC2060 Series Manuale utente