Wenger 1-Column Manuale utente
Owner’s Manual
Media Storage Systems
Mobile Media Cabinets
©Wenger Corporation 2014 Printed in USA 08/14 Part #258A997-02
Wenger Corporation, 555 Park Drive, P.O. Box 448, Owatonna, Minnesota 55060-0448
Questions? Call.....USA: 1-800-4WENGER (493-6437) • Worldwide: 1-507-455-4100 • www.wengercorp.com
Contents
Important User Information . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Component Identication. . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Hardware Parts List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Weight Limits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Digital Lock Accessory Note . . . . . . . . . . . . . . . . . . . . . . . . . .4
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Template for Mounting Power Strip. . . . . . . . . . . . . . . . . . . . .10
1-Column
Mobile Media
Storage Cabinet
2-Column
Mobile Media
Storage Cabinet
Note: Please read and understand these instructions before starting the installation.
Note: Examine the illustrations on the following pages. If you need additional information,
contact Wenger Corporation using the information below.
Visit the Media Storage Cabinet web page at www.wengercorp.com.
2
Important User Information
General
Copyright©2014 by Wenger Corporation
All rights reserved. No part of the contents of this manual may be reproduced, copied, or transmitted
in any form or by any means including graphic, electronic, or mechanical methods or photocopying,
recording, or information storage and retrieval systems without the written permission of the publisher,
unless it is for the purchaser’s personal use.
Printed and bound in the United States of America.
The information in this manual is subject to change without notice and does not represent a commitment
on the part of Wenger Corporation. Wenger Corporation does not assume any responsibility for any
errors that may appear in this manual.
In no event will Wenger Corporation be liable for technical or editorial omissions made herein, nor for
direct, indirect, special, incidental, or consequential damages resulting from the use or defect of this
manual.
The information in this document is not intended to cover all possible conditions and situations that
might occur. The end user must exercise caution and common sense when assembling or installing
Wenger Corporation products. If any questions or problems arise, call Wenger Corporation at 1-800-
887-7145.
Manufacturer
The Media Storage Systems are manufactured by:
Wenger Corporation
555 Park Drive
Owatonna, MN 55060
1-800-4WENGER (493-6437) • 1-507-455-4100
www.wengercorp.com
Intended Use
· This product is intended for indoor use in normal ambient temperature and humidity conditions —
it must not be exposed to prolonged outside weather conditions.
· This product is intended to be assembled and used only as described in these instructions.
Warranty
This product is guaranteed free of defects in materials and workmanship for ten full years from
date of shipment. A full warranty statement is available upon request.
Optional power strips, digital locks and other electronic equipment are covered by the
individual manufacturer’s warranty.
3
Component Identication
Adjustable
Shelf
Cord
Wrap
Fixed
Shelf
Rackmount
Full Width
Slide-Out
Shelf
4” (10 cm)
Drawer
File
Drawer
Cable Pass
Through
Structural Components
Wire
Clamp
Work
Surface
Rear Access
Door
Power Strip
Accessory
X0003278
Digital Lock
Accessory
241C399
Accessories
Small Plastic Bin
Accessory
204A007.113
Medium Plastic Bin
Accessory
204A007.120
Medium Divided Plastic Bin
Accessory
204A007.115
4
Weight Limits
These structural components are rated at the maximum load capacities.
· 4” (10 cm) Drawer - 40 lbs (18 kg).
· File Drawer - 65 lbs (29 kg).
· Fixed, Adjustable and Slide-Out Shelves - 40 lbs (18 kg) per shelf.
Hardware Parts List
*Quantities may vary, extras can be discarded.
X003599
Shelf Clip X003600
Wire Clamp
and
X000482
#8 x 5/8
Sheet Metal Screw
X003632
Cage Nut
Digital Lock Accessory Note
The Digital Lock Accessory is supplied in the “PRIVATE” operating mode.
In this mode, the user must enter a four-digit User Code to open it. The unit will re-lock itself
after four seconds.
The lock can be opened at any time using the Master Code. Unless manufactured to special order,
the default Master Code is 11 33 55 77 and the default User Code is 22 44.
These codes are common to all standard locks and it is very important that you set your own personal
Master and User Codes.
Your lock is not secure until you have changed the default Master and User Codes.
Keep a safe record of your Master Code as it is not possible to make any programming changes
without it.
Please see programming guide to set your own codes.
5
Installation
IMPORTANT: The following procedures are shown using the 2-Column Mobile Media Cabinet,
the procedures for the 1-Column Mobile Media Cabinet are similar unless
indicated otherwise.
Position the Adjustable Shelves
1. Remove any screws that held the Adjustable Shelves in place during shipping.
These screws can be discarded.
2. For each Adjustable Shelf being placed, position one Shelf Clip at even elevations
on each of the four Rails.
3. Tilt each Shelf up on one side slightly as shown and pull it out to remove.
Remove
Screws
6
Installation (continued)
Position the Adjustable Shelves (continued)
4. Fitting the grooves in the Shelves over the Rails, tilt the Shelves into position to rest
on the Shelf Clips.
Shelf Clip
Groove in
Shelf
7
Operation
Repositioning Drawers and Slide-Out Shelves
1. Drawers and Half Width Slide-Out Shelves can be repositioned at different heights
in 1/2” (1.27 cm) increments by relocating the Glides along the Rails.
a. Remove the Drawer or the Slide-Out Shelf and Stop Bracket from the Glides
by rst pulling it outward, then tilting it up and lifting it out.
The Stop Bracket can either be on the top or bottom of the Slide-Out Shelf.
The Plastic Bumper does not need to be removed from the Slide-Out Shelf.
b. Remove either the top or bottom set of Screws and Clips attaching both Glides to the Rails.
c. Relocate the Glides at even elevations on each of the four Rails and reattach the
Screws and Clips to secure them into place.
d. Reinstall the Drawer or the Shelf and Stop Bracket.
Only 1-Column Slide-Out Shelf can be repositioned.
The 2-Column Slide-Out Shelf is shown below only to reference the Stop Bracket location.
Glide
Plastic
Bumper
Stop
Bracket
Screws
Only the top or bottom set
of Screws and Clips need
to be removed.
8
Operation (continued)
Rackmount Electronics
1. Electronic components can be accessed by tipping out the Rackmount.
2. Additional electronic components can be added but must be done so according to their
manufacturer’s specications.
Place deeper components at the bottom of the Rackmount.
3. Knockout Panels can be removed from the Rackmount by twisting them until they break away
from the frame.
4. To open the Rackmount, remove the two Screws securing it to the above Fixed Shelf
and carefully tip it down until the bottom rests on the shelf below.
5. Cage Nuts can be relocated or installed to match component settings.
6. When routing cables inside of the Rackmount, leave enough excess to tip the Panel forward.
Use a fan if electronic component
overheating is a concern.
Do not block the top ventalation
holes.
!CAUTION
Knockout
Panels
Rackmount
Install
Additional
Cage Nuts
Remove
Screws to
Open
9
Operation (continued)
Cable Management
Cable Pass Throughs are located at the top and sides to route cables through the Cabinet.
Notches in the Shelves and Dividers allow cables to be routed at the back of the Cabinet.
Wire Clamps assist in routing cables throughout the Cabinet.
The Clamps can be repositioned or more can be added as needed.
Rear Access Door
Components and connections can also be accessed from the back of the Cabinet through the
lockable Rear Access Door.
Cleaning
Use a soft cotton cloth and a mild detergent to clean the Work Surface.
Avoid using harsh, abrasive detergents or solvents.
Cord
Wraps
Cable Pass
Through
Rear Access
Door
Cable Pass
Through
10
Template for Mounting Power Strip
The Power Strip Accessory may be placed at any location in the Cabinet.
Secure the Power Strip mounting holes using two #8 x 5/8 Sheet Metal Screws
and the template on the following page.
11-1/2 (29.21 cm)
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Wenger Magazzinaggio
