WesAudio _TITAN Manuale utente
WESAUDIO
3/15/17
_TITAN USER MANUAL REV3
1
www.WesAudio.com
_TITAN
User manual
EN
Copyright 2016 by WesAudio
WESAUDIO
3/15/17
_TITAN USER MANUAL REV3
2
Thank You for the purchase of _TITAN
_TITAN
Ng500 compatible frame with digital control.
With kind regards
Radoslaw Wesolowski and Michal Weglicki
WESAUDIO
3/15/17
_TITAN USER MANUAL REV3
3
_TITAN is 500 series compatible (*) rack frame which
implements ng500 connector and GCon protocol.
_TITAN is complete recall system designed to provide total integration with your
beloved analogue equipment. It extends 500 series connector with additional pins
where modules can be designed to support digital recall or any other vendor specific
functionalities. This extension is part of new open standard “ng500” –“Next Generation
500 series” which allows other manufacturers** to design and implement digitally
controlled analog devices.
We are proud to present _TITAN –Future of analog processors.
(*) Important note about 500 series extension: please check “Instalation and compatibility” chapter.
(**) Please check “GCon Open specification framework”.
WESAUDIO
3/15/17
_TITAN USER MANUAL REV3
4
Table of Contents
1. Abbreviations and terms..........................................................................................................................6
2. Installation and compatibility...................................................................................................................7
3. Front panel ...............................................................................................................................................9
4. Overview ................................................................................................................................................10
5. Software .................................................................................................................................................11
5.1. Installation..............................................................................................................................................11
5.1.1. WINDOWS .............................................................................................................................................11
5.1.2. OSX......................................................................................................................................................11
5.1.3. Troubleshooting..................................................................................................................................11
6. Set up GCon Connection. .......................................................................................................................13
6.1. USB .........................................................................................................................................................14
6.2. Ethernet..................................................................................................................................................15
6.2.1. _TITAN Configuration. ........................................................................................................................16
6.2.1.1. DHCP ..........................................................................................................................................17
6.2.2. Static IP address..................................................................................................................................18
6.2.3. Direct connection –setting IP address on PC/MAC............................................................................23
7. Set up Audio signal.................................................................................................................................24
7.1. Rear XLR Connections.............................................................................................................................24
7.2. I.A.C. - Internal Audio Connector. ..........................................................................................................25
8. Stereo links.............................................................................................................................................27
8.1. Stereo link buttons. ................................................................................................................................27
8.2. Stereo links in GConManager.................................................................................................................27
8.3. Stereo links integration with GCon compatible modules. .....................................................................28
9. GConManager ........................................................................................................................................29
9.1. Where is GConManager?....................................................................................................................29
9.2. How to start Firmware Upgrade.........................................................................................................29
9.3. How to check currently connected devices........................................................................................30
10. GCon open specification framework......................................................................................................31
11. Multi Host Support –USB note. .............................................................................................................31
WESAUDIO
3/15/17
_TITAN USER MANUAL REV3
6
1. Abbreviations and terms
GCon –high speed communication protocol which allows full management and recall of analog devices.
Please note that this is just management protocol, audio signal transfer is not in scope of its capabilities.
I.A.C. –Internal Audio Connector, special _TITAN connector which is integrated with internal audio routing,
and allows to connect audio signal directly without any additional wires (please check “I.A.C – Internal Audio
Connector” chapter).
NG500 –Next generation 500 series.
NG500 connector –special connector which extends standardized 500 series connector with additional pins.
UDP - User Datagram Protocol.
WESAUDIO
3/15/17
_TITAN USER MANUAL REV3
7
2. Installation and compatibility.
After unpacking your _TITAN frame, please check for any visible damage that may have occurred
during transit. If there is any problem, please contact your dealer immediately for advice on what to do.
!!!Ensure the rack is completely powered down before attempting modules
installation to prevent damage to the frame!!!
Modules installation walkthrough:
Choose the position in the rack to which you will install the module and slide it in so that the edge
connector of the module aligns with the matching connector in the rack. A gentle push and the module
should slide home into the rack connector. Attach the front panel to the front of the rack with screws
supplied by your rack manufacturer. This is important for mechanical rigidity. Do not over tighten these
screws to avoid stripping out the threads. Apply power, test that everything is working OK, and most
importantly, enjoy!
500 series compatibility note:
_Titan connector was designed to deliver new implementation opportunities, but also to remain
compatible with most of 500 series modules. Nevertheless ng500 series connector is higher than 500
series standard plug and some standard 500 series modules won’t fit into _TITAN. The reason for that is
module’s chassis design at the back, which can prevent the module to fit in correctly.
WESAUDIO
3/15/17
_TITAN USER MANUAL REV3
8
As you can see on above picture, ng500 series connector is higher 9mm comparing to standard 500
series socket (please note that above sockets are matched to each other based on particular pins). To
check if your modules will fit into _TITAN you can send us a query to info@wesaudio.com with description
of modules that you would like to use.
WESAUDIO
3/15/17
_TITAN USER MANUAL REV3
9
3. Front panel
H-LINK note:
If this LED is constantly blinking, that means that _TITAN is in upgrade mode, and firmware upgrade
should be triggered through GConManager application.
WESAUDIO
3/15/17
_TITAN USER MANUAL REV3
10
4. Overview
_Titan main features:
GCon compatible frame which allows to communicate with modules through single connection.
USB connection to manage up to 10 modules.
Ethernet connection (UDP based) to manage up to 10 modules (LAN single subnet).
GConManager application which allows to manage stereo links.
Internal audio signals are routed into special connector accessible on 10th slot, which allows
integration with “Summing Modules” or “Audio interfaces”.
Stereo links are fully integrated. Pressing “Link” button on 2 modules which support GCon
protocol (e.g. _Mimas) sets stereo link on the _Titan.
Open Specification –documentation and software framework including communication drivers
for any Vendor that would like to adopt to this standard.
10 slots with ng500 series connector.
Remote firmware upgrade –_Titan & all modules inside can be upgraded remotely through USB
or Ethernet connection.
XLR sockets in/out for each slot.
Internal stereo link switches which can be also managed through GConManager standalone
application.
Linear power supply capable to deliver 5A of power.
Power mode switch –115V/230V.
Warranty: 2 years.
Indice
